101602-7780 ZEXEL 9 400 610 593 BOSCH INJECTION-PUMP ASSEMBLY 9400610593 1016027780 1156030540


 

Information injection-pump assembly

BOSCH 9 400 610 593 9400610593
ZEXEL 101602-7780 1016027780
ISUZU 1156030540 1156030540
101602-7780 INJECTION-PUMP ASSEMBLY
Rating:
13
Buy INJECTION-PUMP ASSEMBLY 101602-7780 zexel genuine, new aftermarket engine parts with delivery

Service parts 101602-7780 INJECTION-PUMP ASSEMBLY:

1. _
2. FUEL INJECTION PUMP 101060-6390
3. GOVERNOR 105410-9990
4. SUPPLY PUMP 105220-5220
5. AUTOM. ADVANCE MECHANIS
6. COUPLING PLATE 105661-3230
7. COUPLING PLATE 156639-0420
8. _
9. _
10. NOZZLE AND HOLDER ASSY 105101-6081
11. Nozzle and Holder 1-15300-247-1
12. Open Pre:MPa(Kqf/cm2) 18.1{185}
13. NOZZLE-HOLDER 105030-3201
14. NOZZLE 105015-8210
15. NOZZLE SET

Include in #1:

101602-7780 as INJECTION-PUMP ASSEMBLY

Cross reference number

BOSCH 9 400 610 593 9400610593
ZEXEL 101602-7780 1016027780
ISUZU 1156030540 1156030540


Zexel num
Bosch num
Firm num
Name
101602-7780 
9 400 610 593 
1156030540  ISUZU
INJECTION-PUMP ASSEMBLY
6BG1-T K 14BF INJECTION PUMP ASSY PE6AD PE

Calibration Data:

Adjustment conditions
Test oil
1404 Test oil
  ISO4113 or {SAEJ967d}
Test oil temperature degC   40 40 45
Nozzle and nozzle holder   105780-8140
Bosch type code   EF8511/9A
Nozzle   105780-0000
Bosch type code   DN12SD12T
Nozzle holder   105780-2080
Bosch type code   EF8511/9
Opening pressure MPa   17.2
Opening pressure kgf/cm2   175
Injection pipe
Outer diameter - inner diameter - length (mm)
mm   6-2-600
Overflow valve   131424-4920
Overflow valve opening pressure kPa   127 107 147
Overflow valve opening pressure kgf/cm2   1.3 1.1 1.5
Tester oil delivery pressure kPa   157 157 157
Tester oil delivery pressure kgf/cm2   1.6 1.6 1.6
Direction of rotation (viewed from drive side)
Right
  R
Injection timing adjustment
Direction of rotation (viewed from drive side)
Right
  R
Injection order   1-5-3-6- 2-4
Pre-stroke mm   3.6 3.55 3.65
Beginning of injection position
Drive side
  NO.1
Difference between angles 1
Cal 1-5
deg.   60 59.5 60.5
Difference between angles 2
Cal 1-3
deg.   120 119.5 120.5
Difference between angles 3
Cal 1-6
deg.   180 179.5 180.5
Difference between angles 4
Cyl.1-2
deg.   240 239.5 240.5
Difference between angles 5
Cal 1-4
deg.   300 299.5 300.5
Injection quantity adjustment
Adjusting point   A
Rack position   10.9
Pump speed r/min   1250 1250 1250
Average injection quantity mm3/st.   99.4 97.9 100.9
Max. variation between cylinders %   0 -2.5 2.5
Basic   *
Fixing the lever   *
Injection quantity adjustment_02
Adjusting point   B
Rack position   6.7+-0.5
Pump speed r/min   365 365 365
Average injection quantity mm3/st.   9.8 8.5 11.1
Max. variation between cylinders %   0 -14 14
Fixing the rack   *

Test data Ex:

Governor adjustment

Test data 101602-7780
N:Pump speed R:Rack position (mm) (1)Target notch: K (2)Tolerance for racks not indicated: +-0.05mm. (3)Set idle sub-spring (4)Main spring setting (5)Rack difference between N = N1 and N = N2
----------
K=8 N1=1250r/min N2=800r/min
----------

Speed control lever angle

Test data 101602-7780
F:Full speed I:Idle (1)Stopper bolt setting
----------

----------
a=(5deg)+-5deg b=(24deg)+-5deg

Stop lever angle

Test data 101602-7780
N:Pump normal S:Stop the pump.
----------

----------
a=12deg+-5deg b=46deg+-5deg

Timing setting

Test data 101602-7780
(1)Pump vertical direction (2)Position of coupling's threaded hole at No 1 cylinder's beginning of injection (3)B.T.D.C.: aa (4)-
----------
aa=15deg
----------
a=(20deg)




Information:

Cautions Regarding Battery* Handle Battery Carefully * Never use flames or allow sparks near the battery. The battery releases flammable hydrogen gas and oxygen gas. These gases can be ignited by flames and cause an explosion.* Do not use the battery when the fluid surface is lower than the minimum level. Using a battery with a low electrolyte level can result in an explosion.* Do not short the battery terminals with a tool or other metal object.* When disconnecting battery cables, always remove the cable from the negative (-) terminal first. When reconnecting cables, attach the cable to the positive (+) terminal first.* Charge the battery in a well-ventilated area, with all filling hole plugs removed.* Make sure the cable clamps are securely installed on the battery terminals. A loose cable clamp can cause sparks that may result in explosion.* Before servicing electrical components or conducting electrical welding, set the battery switch to the [Open/OFF] position or disconnect the cable from the negative (-) battery terminal to cut off the electrical current.* Electrolyte (battery fluid) contains dilute sulfuric acid. Careless handling of the battery can lead to the loss of sight and/or burns. Also, do not swallow electrolyte.* Wear protective goggles and rubber gloves when maintaining and inspecting the battery (when adding water, charging, etc.).* If electrolyte is spilled onto the skin or clothes, immediately wash with lots of clean fresh water and thoroughly clean with soap.* If electrolyte gets into eyes, immediately flush with lots of clean fresh water and seek immediate medical attention.* Should you accidentally swallow electrolyte, gargle with plenty of water, then drink lots of water, and seek immediate medical attention.
Response To Abnormalities* If Engine Overheats, Conduct Heating Operation Before Stopping The Engine If the engine overheats, do not stop the engine immediately. Abruptly stopping an overheated engine may cause the coolant temperature to rise, resulting in seizing of the engine. If the engine overheats, operate the engine at low idling speed (cooling temperature), and stop the engine after the coolant temperature lowers sufficiently.Do not add coolant immediately after stopping the engine. Adding coolant to a hot engine may cause damage to the cylinder heads due to sudden change in temperature. Add coolant after the engine cools to room temperature.* If Engine Stops Due To Abnormality, Exercise Caution When Restarting If the engine stops due to an abnormality, do not restart the engine immediately. If the engine stops with an alarm, check and correct the cause of the problem before restarting. Operating the engine without correcting the problem may result in serious engine problems.* If Oil Pressure Drops, Stop Engine Immediately If the engine oil pressure decreases, stop the engine immediately, and inspect the lubrication system. Operating the engine with low oil pressure may cause seizing of the bearings and other parts.* If Fan Belt Breaks, Stop Engine Immediately If the fan belt breaks, stop the engine immediately. Continued operation of the engine without the fan belt causes coolant to change to steam and

Have questions with 101602-7780?





Group cross 101602-7780 ZEXEL

 
 
INJECTION-PUMP ASSEMBLY

Isuzu 

 
1156029720 
INJECTION-PUMP ASSEMBLY
6BG1-T
 
 
INJECTION-PUMP ASSEMBLY

Isuzu 

9 400 610 587 
1156029910 
INJECTION-PUMP ASSEMBLY
6BG1
9 400 610 588 
1156029920 
INJECTION-PUMP ASSEMBLY
6BG1-T
9 400 610 589 
1156030410 
INJECTION-PUMP ASSEMBLY
6BG1-TQB
9 400 610 590 
1156030400 
INJECTION-PUMP ASSEMBLY
6BG1-TQC
9 400 610 591 
1156030490 
INJECTION-PUMP ASSEMBLY
6BG1-TQA
9 400 610 592 
1156030520 
INJECTION-PUMP ASSEMBLY
6BG1-T
9 400 614 913 
1156030530 
INJECTION-PUMP ASSEMBLY
6BG1-T
101602-7780  
9 400 610 593 
1156030540 
INJECTION-PUMP ASSEMBLY
6BG1-T
9 400 614 914 
1156030550 
INJECTION-PUMP ASSEMBLY
6BG1-T
Back to top