Information injection-pump assembly
BOSCH
9 400 614 878
9400614878
ZEXEL
101602-7120
1016027120
ISUZU
1156024360
1156024360
Rating:
Service parts 101602-7120 INJECTION-PUMP ASSEMBLY:
1.
_
5.
AUTOM. ADVANCE MECHANIS
6.
COUPLING PLATE
8.
_
9.
_
10.
NOZZLE AND HOLDER ASSY
11.
Nozzle and Holder
12.
Open Pre:MPa(Kqf/cm2)
18.1(185)
13.
NOZZLE-HOLDER
15.
NOZZLE SET
Include in #1:
101602-7120
as INJECTION-PUMP ASSEMBLY
Include in #2:
104741-1181
as _
Cross reference number
BOSCH
9 400 614 878
9400614878
ZEXEL
101602-7120
1016027120
ISUZU
1156024360
1156024360
Zexel num
Bosch num
Firm num
Name
101602-7120
9 400 614 878
1156024360 ISUZU
INJECTION-PUMP ASSEMBLY
6BD1 * K
6BD1 * K
Calibration Data:
Adjustment conditions
Test oil
1404 Test oil ISO4113 or {SAEJ967d}
1404 Test oil ISO4113 or {SAEJ967d}
Test oil temperature
degC
40
40
45
Nozzle and nozzle holder
105780-8140
Bosch type code
EF8511/9A
Nozzle
105780-0000
Bosch type code
DN12SD12T
Nozzle holder
105780-2080
Bosch type code
EF8511/9
Opening pressure
MPa
17.2
Opening pressure
kgf/cm2
175
Injection pipe
Outer diameter - inner diameter - length (mm) mm 6-2-600
Outer diameter - inner diameter - length (mm) mm 6-2-600
Overflow valve opening pressure
kPa
157
123
191
Overflow valve opening pressure
kgf/cm2
1.6
1.25
1.95
Tester oil delivery pressure
kPa
157
157
157
Tester oil delivery pressure
kgf/cm2
1.6
1.6
1.6
Direction of rotation (viewed from drive side)
Right R
Right R
Injection timing adjustment
Direction of rotation (viewed from drive side)
Right R
Right R
Injection order
1-5-3-6-
2-4
Pre-stroke
mm
3.6
3.55
3.65
Beginning of injection position
Drive side NO.1
Drive side NO.1
Difference between angles 1
Cal 1-5 deg. 60 59.5 60.5
Cal 1-5 deg. 60 59.5 60.5
Difference between angles 2
Cal 1-3 deg. 120 119.5 120.5
Cal 1-3 deg. 120 119.5 120.5
Difference between angles 3
Cal 1-6 deg. 180 179.5 180.5
Cal 1-6 deg. 180 179.5 180.5
Difference between angles 4
Cyl.1-2 deg. 240 239.5 240.5
Cyl.1-2 deg. 240 239.5 240.5
Difference between angles 5
Cal 1-4 deg. 300 299.5 300.5
Cal 1-4 deg. 300 299.5 300.5
Injection quantity adjustment
Adjusting point
A
Rack position
8.9
Pump speed
r/min
800
800
800
Average injection quantity
mm3/st.
56.5
55
58
Max. variation between cylinders
%
0
-2
2
Basic
*
Fixing the lever
*
Injection quantity adjustment_02
Adjusting point
B
Rack position
8.6
Pump speed
r/min
1400
1400
1400
Average injection quantity
mm3/st.
58.8
56.8
60.8
Max. variation between cylinders
%
0
-4
4
Fixing the lever
*
Injection quantity adjustment_03
Adjusting point
-
Rack position
6.5+-0.5
Pump speed
r/min
325
325
325
Average injection quantity
mm3/st.
9.4
8
10.8
Max. variation between cylinders
%
0
-14
14
Fixing the rack
*
Remarks
Adjust only variation between cylinders; adjust governor according to governor specifications.
Adjust only variation between cylinders; adjust governor according to governor specifications.
Test data Ex:
Governor adjustment
N:Pump speed
R:Rack position (mm)
(1)Target notch: K
----------
K=6
----------
----------
K=6
----------
Speed control lever angle
F:Full speed
I:Idle
S:Stop
(1)Set the stopper bolt (seal at shipping).
----------
----------
a=13deg+-5deg b=32deg+-5deg c=32deg+-3deg
----------
----------
a=13deg+-5deg b=32deg+-5deg c=32deg+-3deg
Stop lever angle
N:Pump normal
S:Stop the pump.
----------
----------
a=12deg+-5deg b=46deg+-5deg
----------
----------
a=12deg+-5deg b=46deg+-5deg
Timing setting
(1)Pump vertical direction
(2)Position of gear mark 'CC' at No 1 cylinder's beginning of injection
(3)B.T.D.C.: aa
(4)-
----------
aa=20deg
----------
a=(90deg)
----------
aa=20deg
----------
a=(90deg)
Information:
PARTS NEEDED
Qty
Part Number Description
6 1R6573 GASKET
1 2941706 GASKET
6 2941788 SEAL
1 2941790 PIPE
1 2941791 PIPE
1 2941792 PIPE
1 2941793 PIPE
1 2941794 PIPE
1 2941795 PIPE
6 2941803 SEAL-O-RING
6 3264756 INJECTOR GP-F -G
1 3280972 SOFTWARE GP-ELEK
In order to allow equitable parts availability to all participating dealers, please limit your initial parts order to not exceed 2% of dealership population. This is an initial order recommendation only, and the ultimate responsibility for ordering the total number of parts needed to satisfy the program lies with the dealer.
ACTION REQUIRED
If your engine is experiencing a lack of power and/or black smoke emissions, complete the following actions:
- Replace the six fuel injectors at the time of repair. Replace the existing unit injectors with the new 326-4756 Fuel Injector Groups. Refer to KENR8106, Disassembly and Assembly, for removal/install procedure of the fuel injector groups.
- Flash the new engine 328-0972 Software Group. The new engine software will change the engine power and therefore it is needed to request a Factory Password before flashing.
SERVICE CLAIM ALLOWANCES
Product smu/age whichever comes first Caterpillar Dealer Suggested Customer Suggested
Parts % Labor Hrs% Parts % Labor Hrs% Parts % Labor Hrs%
0-4000 hrs,
0-60 mo 100.0% 100.0% 0.0% 0.0% 0.0% 0.0%
4001-6000 hrs,
61-90 mo 33.0% 50.0% 0.0% 0.0% 50.0% 50.0%
This is a 4.0-hour job
PARTS DISPOSITION
Handle the parts in accordance with your Warranty Bulletin on warranty parts handling.
Have questions with 101602-7120?
Group cross 101602-7120 ZEXEL
Isuzu
101602-7120
9 400 614 878
1156024360
INJECTION-PUMP ASSEMBLY
6BD1
6BD1