101601-8480 ZEXEL INJECTION-PUMP ASSEMBLY Calibration Data 1016018480 1156015870

Information Cross number Calibration Data Calibration Data Ex

Information injection-pump assembly

ZEXEL 101601-8480 1016018480

ISUZU 1156015870 1156015870

Price: query

Buy now
Add to cart Go to cart

Rating:

Buy INJECTION-PUMP ASSEMBLY 101601-8480 zexel genuine, new aftermarket engine parts with delivery

Service parts 101601-8480 INJECTION-PUMP ASSEMBLY:

1. _

2. FUEL INJECTION PUMP 101060-2710

3. GOVERNOR 105931-1820

4. SUPPLY PUMP 105220-4781

5. AUTOM. ADVANCE MECHANIS 105612-3190

6. COUPLING PLATE 105661-0681

7. COUPLING PLATE

8. _

9. _

10. NOZZLE AND HOLDER ASSY 105100-6060

11. Nozzle and Holder 1-15300-135-0

12. Open Pre:MPa(Kqf/cm2) 18.1(185)

13. NOZZLE-HOLDER 105031-3930

14. NOZZLE 105015-5730

15. NOZZLE SET

Include in #1:

101601-8480 as INJECTION-PUMP ASSEMBLY

106689-4070 as _

Cross reference number

ZEXEL 101601-8480 1016018480

ISUZU 1156015870 1156015870

Zexel num

Bosch num

Firm num

Name

101601-8480

1156015870 ISUZU

INJECTION-PUMP ASSEMBLY
6BD1-T * K

Calibration Data:

Adjustment conditions

Test oil
1404 Test oil ISO4113 or {SAEJ967d}

Test oil temperature degC 40 40 45

Nozzle and nozzle holder 105780-8140

Bosch type code EF8511/9A

Nozzle 105780-0000

Bosch type code DN12SD12T

Nozzle holder 105780-2080

Bosch type code EF8511/9

Opening pressure MPa 17.2

Opening pressure kgf/cm2 175

Injection pipe
Outer diameter - inner diameter - length (mm) mm 6-2-600

Overflow valve opening pressure kPa 157 123 191

Overflow valve opening pressure kgf/cm2 1.6 1.25 1.95

Tester oil delivery pressure kPa 157 157 157

Tester oil delivery pressure kgf/cm2 1.6 1.6 1.6

Direction of rotation (viewed from drive side)
Right R

Injection timing adjustment

Direction of rotation (viewed from drive side)
Right R

Injection order 1-5-3-6- 2-4

Pre-stroke mm 3.4 3.35 3.45

Rack position
After adjusting injection quantity. R=A

Beginning of injection position
Drive side NO.1

Difference between angles 1
Cal 1-5 deg. 60 59.5 60.5

Difference between angles 2
Cal 1-3 deg. 120 119.5 120.5

Difference between angles 3
Cal 1-6 deg. 180 179.5 180.5

Difference between angles 4
Cyl.1-2 deg. 240 239.5 240.5

Difference between angles 5
Cal 1-4 deg. 300 299.5 300.5

Injection quantity adjustment

Adjusting point -

Rack position 13.8

Pump speed r/min 950 950 950

Average injection quantity mm3/st. 71.4 69.8 73

Max. variation between cylinders % 0 -2.5 2.5

Basic *

Fixing the rack *

Standard for adjustment of the maximum variation between cylinders *

Injection quantity adjustment_02

Adjusting point H

Rack position 9.5+-0.5

Pump speed r/min 275 275 275

Average injection quantity mm3/st. 10 8.7 11.3

Max. variation between cylinders % 0 -14 14

Fixing the rack *

Standard for adjustment of the maximum variation between cylinders *

Injection quantity adjustment_03

Adjusting point A

Rack position R1(13.8)

Pump speed r/min 950 950 950

Average injection quantity mm3/st. 71.4 70.4 72.4

Basic *

Fixing the lever *

Injection quantity adjustment_04

Adjusting point B

Rack position R1-0.2

Pump speed r/min 1500 1500 1500

Average injection quantity mm3/st. 77.4 74.2 80.6

Fixing the lever *

Injection quantity adjustment_05

Adjusting point C

Rack position R1-0.15

Pump speed r/min 1300 1300 1300

Average injection quantity mm3/st. 75.8 72.6 79

Fixing the lever *

Injection quantity adjustment_06

Adjusting point D

Rack position R1-0.45

Pump speed r/min 600 600 600

Average injection quantity mm3/st. 45 43.4 46.6

Fixing the lever *

Injection quantity adjustment_07

Adjusting point I

Rack position 15.7+-0. 5

Pump speed r/min 150 150 150

Average injection quantity mm3/st. 74 74 79

Fixing the lever *

Rack limit *

Timer adjustment

Pump speed r/min 1050--

Advance angle deg. 0 0 0

Remarks
Start

Timer adjustment_02

Pump speed r/min 1000

Advance angle deg. 0.5

Timer adjustment_03

Pump speed r/min 1300

Advance angle deg. 0.9 0.4 1.4

Timer adjustment_04

Pump speed r/min 1600

Advance angle deg. 2 1.5 2.5

Remarks
Finish

Test data Ex:

Governor adjustment

N:Pump speed R:Rack position (mm) (1)Torque cam stamping: T1 (2)RACK LIMIT
----------
T1=A31
----------

Speed control lever angle

F:Full speed I:Idle (1)Use the hole at R = aa (2)Stopper bolt set position 'H'
----------
aa=35mm
----------
a=43deg+-5deg b=41deg+-3deg

Stop lever angle

N:Pump normal S:Stop the pump.
----------

----------
a=25deg+-5deg b=40deg+-5deg

Timing setting

(1)Pump vertical direction (2)Position of timer's threaded hole at the No. 1 cylinder's beginning of injection (3)B.T.D.C.: aa (4)-
----------
aa=10deg
----------
a=(60deg)

Information:

1. Remove fuel line (1) and (3) from the fuel transfer pump.2. Put caps in the fuel line openings to prevent fuel system contamination.3. Remove bolts (2), and remove fuel transfer pump (4). Check the condition of the O-ring seal on the fuel transfer pump. If necessary, make a replacement. The following steps are for installtion of the fuel transfer pump.4. Be sure the O-ring seal is in position on the fuel transfer pump. Put clean engine oil on the O-ring seal.5. Put fuel transfer pump (4) in position, and install the bolts that hold it in place.6. Remove the caps from the fuel line openings, and install fuel lines (1) and (3).Disassemble Fuel Transfer Pump
Start By:a. remove fuel transfer pump 1. Remove seal (1) from the fuel transfer pump.
Cover (2) is under spring tension. Remove the bolts that hold cover (2) slowly to prevent injury.
2. Remove bolts (3) and cover (2) from the housing. 3. Remove seals (4) and valve (5) from cover (2). 4. Remove spring (6) from the piston.
Mark the orientation of valve (8) as to its location in the housing.
5. Remove washer (7), valve (8) and the seal from the housing. 6. Remove piston (9) and sleeve (10) from the housing. 7. Remove seal (11) from sleeve (12). 8. Remove guide and tappet assembly (13) from the housing. 9. Remove seal (14) from guide (15).
If tappet (17) or the guide are damaged or worn, they must be replaced as a unit.
10. Remove ring (16) from tappet (17) and the tappet from guide (15). 11. Remove the bolts and cover (18) from the housing. 12. Remove seal (19) from cover (18). 13. Remove valve (20) from the housing if necessary.Assemble Fuel Transfer Pump
1. Install valve (20) in housing as shown. 2. Put clean fuel on seal (19), and install it on cover (18).3. Install cover (18) on the housing.
The tappet and guide must be serviced as a unit.
4. Install tappet (17) in guide (15). Install ring (16) on tappet (17) to hold the tappet in the guide. 5. Put clean fuel on seal (14), and install it on guide and tappet assembly (13).6. Install guide and tappet assembly (13) in the housing as shown. 7. Put clean fuel on seal (11), and install it on sleeve (12).8. Install sleeve (12) in the housing. 9. Install piston (9) in the housing. 10. Install seal, valve (8) and washer (7) in the housing as shown. Be sure valve (8) is the correct position in the housing. 11. Install spring (6) in the piston. 12. Install valve (5) in cover (2) as shown.13. Put clean fuel on seals (4), and put them in position on cover (2).14. Install cover (2) on the housing. 15. Put seal (1) in position on the fuel transfer pump.16. Install the fuel transfer pump on the fuel injection pump housing.End By:a. install fuel transfer pump