101601-5442 ZEXEL INJECTION-PUMP ASSEMBLY Cross 1016015442 220006160b


 

Information injection-pump assembly

ZEXEL 101601-5442 1016015442
HINO 220006160B 220006160b
101601-5442 INJECTION-PUMP ASSEMBLY
Rating:
61
Buy INJECTION-PUMP ASSEMBLY 101601-5442 zexel genuine, new aftermarket engine parts with delivery

Cross reference number

Zexel num
Bosch num
Firm num
Name
101601-5442 
 
220006160B  HINO
INJECTION-PUMP ASSEMBLY
H07D-A * K




Information:

Start By:a. remove oil pump1. Check the connecting rods and caps for their identification and location. 2. Turn the crankshaft until the connecting rod caps are in position.3. Remove two bolts (1) and the cap from the connecting rod. Remove the lower half of the bearing from the cap.4. Push the connecting rod away from the crankshaft. Remove the upper half of the bearing from the connecting rod. Install the bearings dry when the clearance checks are made. Put clean engine oil on the bearings for final assembly.5. Install the upper half of the bearing in the connecting rod.6. Pull the connecting rod slowly on to the crankshaft.7. Install the lower half of the bearing in the cap. Be sure the tabs in the back of bearings are in the tab grooves of the connecting rod and cap.The serviceman must be very careful to use Plastigage, tool (A) correctly. The following points must be remembered:... Make sure that the backs of the bearings and the bores are clean and dry.... Make sure that the bearing locking tabs are properly seated in their slots.... The crankshaft must be free of oil where the Plastigage touches it.... Put a piece of Plastigage (A) on the crown of the bearing half that is in the cap. Do not allow the Plastigage to extend over the edge of the bearing.... Install the bearing cap using the correct torque-turn specifications. Do not use an impact wrench. Be careful not to dislodge the bearing when the cap is installed.... Do not turn the crankshaft with the Plastigage installed.... Carefully remove the cap but do not remove the Plastigage. Measure the width of the Plastigage while it is in the bearing cap or on the crankshaft journal. Do this by using the correct scale on the package. Record the measurements.... Remove the Plastigage before reinstalling the cap.When using Plastigage, the readings can sometimes be unclear. For example, all parts of the Plastigage are not the same width. Measure the major widths to make sure that they are within the specification range. Also, experience has shown that when checking clearances tighter than 0.10 mm (.004 in.) the readings may be low by 0.013 to 0.025 mm (.0005 to .0010 in.). Out-of-round journals can give faulty readings. Also, journal taper may be indicated when one end of the Plastigage is wider that the other.For complete details concerning measuring bearing clearances, see Engine Bearings And Crankshafts, Form No. SEBD0531. 8. Use Plastigage (A) to check the bearing clearance.9. Put Plastigage (A) on the bearing.10. Put 2P2506 Thread Lubricant on the threads of the rod bolts and seat surfaces of the nuts. Be sure the cylinder numbers on the rod cap and rod are the same and are on the same side of connecting rod. Numbers are on the same side of the rod and cap as are the bearing tab slots. If new rods are installed, put the cylinder number on the rod and cap. Do not turn

Have questions with 101601-5442?





Group cross 101601-5442 ZEXEL

 
 
INJECTION-PUMP ASSEMBLY

Hino 

 
220801480A 
INJECTION-PUMP ASSEMBLY
9 400 614 612 
220801480A 
INJECTION-PUMP ASSEMBLY
H07-1
 
 
INJECTION-PUMP ASSEMBLY

Hino 

 
220006120A 
INJECTION-PUMP ASSEMBLY
W06D-T
 
220006140A 
INJECTION-PUMP ASSEMBLY
H07D-A
 
220006140B 
INJECTION-PUMP ASSEMBLY
H07D-A
 
220006150A 
INJECTION-PUMP ASSEMBLY
H07D-A
 
220006150B 
INJECTION-PUMP ASSEMBLY
H07D-A
 
220006160A 
INJECTION-PUMP ASSEMBLY
H07D-A
101601-5442  
 
220006160B 
INJECTION-PUMP ASSEMBLY
H07D-A
 
220006170A 
INJECTION-PUMP ASSEMBLY
H07D-A
 
220006170B 
INJECTION-PUMP ASSEMBLY
H07D-A
 
220006210A 
INJECTION-PUMP ASSEMBLY
W06E
 
220006211A 
INJECTION-PUMP ASSEMBLY
W06E
 
220006212A 
INJECTION-PUMP ASSEMBLY
W06E
 
 
INJECTION-PUMP ASSEMBLY
 
 
INJECTION-PUMP ASSEMBLY

Hino 

9 400 614 613 
220006213A 
INJECTION-PUMP ASSEMBLY
W06E
 
 
INJECTION-PUMP ASSEMBLY
 
 
INJECTION-PUMP ASSEMBLY

Hino 

9 400 614 614 
220006220A 
INJECTION-PUMP ASSEMBLY
W06E
F 019 Z10 589 
220006230A 
INJECTION-PUMP ASSEMBLY
W06E
F 01G 09U 02U 
220006231A 
INJECTION-PUMP ASSEMBLY
W06E
F 01G 09U 02V 
 
INJECTION-PUMP ASSEMBLY

Hino 

9 400 614 615 
220006232A 
INJECTION-PUMP ASSEMBLY
W06E-E
 
 
INJECTION-PUMP ASSEMBLY

Hino 

9 400 614 616 
220006250A 
INJECTION-PUMP ASSEMBLY
W06D
Back to top