Information injection-pump assembly
ZEXEL
101601-4180
1016014180
ISUZU
5156004243
5156004243
Rating:
Service parts 101601-4180 INJECTION-PUMP ASSEMBLY:
1.
_
3.
GOVERNOR
7.
COUPLING PLATE
8.
_
9.
_
11.
Nozzle and Holder
5-15300-089-1
12.
Open Pre:MPa(Kqf/cm2)
18.1{185}
15.
NOZZLE SET
Cross reference number
Zexel num
Bosch num
Firm num
Name
Information:
Recommended Procedure With Chassis Dynamometer
Possible Causes/CorrectionsMinor Operating Faults
To help identify a problem before a more involved troubleshooting procedure is started, follow the procedure given in the Primary Engine Checks section.Fuel Ratio Control Out Of Adjustment Or Bad
Follow the procedure in the Testing and Adjusting section of this Service Manual.Check Engine Performance
Do a Power Analysis Report (PAR), Level II, to check engine performance. See Special Instruction, Form No. SEHS8025 and SEHS7886 for the tooling and procedures to use. Be sure to make a record of the temperatures for inlet air, fuel (at filter base), lubricating oil and coolant. Make the necessary adjustments or repairs to the engine if needed.At this point, the governor fuel settings should be verified. See the Testing and Adjusting section of this Service Manual for the necessary procedures. Also, refer back to the information learned earlier (see Owner/Operator Input section) about the truck specifications and application and judge whether or not the engine is performing as expected or customer expectation is realistic.Recommended Procedure Without Chassis Dynamometer
Possible Causes/CorrectionsMinor Operating Faults
To help identify a problem before a more involved troubleshooting procedure is started, follow the procedure given in the Primary Engine Checks section.Fuel Ratio Control Out Of Adjustment Or Bad
Follow the procedure in the Testing and Adjusting section of this Service Manual.Fuel Injection Timing Not Correct
Follow the procedures in the Testing and Adjusting section of this Service Manual.Check Engine Performance
Install the tooling and follow the procedure given in the Road Test section.At this point, the governor fuel settings should be verified. See the Testing and Adjusting section of this Service Manual for the necessary procedures. Also, refer back to the information learned earlier (see Owner/Operator Input section) about the truck specifications and application and judge whether or not the engine is performing as expected or customer expectation is realistic.
Possible Causes/CorrectionsMinor Operating Faults
To help identify a problem before a more involved troubleshooting procedure is started, follow the procedure given in the Primary Engine Checks section.Fuel Ratio Control Out Of Adjustment Or Bad
Follow the procedure in the Testing and Adjusting section of this Service Manual.Check Engine Performance
Do a Power Analysis Report (PAR), Level II, to check engine performance. See Special Instruction, Form No. SEHS8025 and SEHS7886 for the tooling and procedures to use. Be sure to make a record of the temperatures for inlet air, fuel (at filter base), lubricating oil and coolant. Make the necessary adjustments or repairs to the engine if needed.At this point, the governor fuel settings should be verified. See the Testing and Adjusting section of this Service Manual for the necessary procedures. Also, refer back to the information learned earlier (see Owner/Operator Input section) about the truck specifications and application and judge whether or not the engine is performing as expected or customer expectation is realistic.Recommended Procedure Without Chassis Dynamometer
Possible Causes/CorrectionsMinor Operating Faults
To help identify a problem before a more involved troubleshooting procedure is started, follow the procedure given in the Primary Engine Checks section.Fuel Ratio Control Out Of Adjustment Or Bad
Follow the procedure in the Testing and Adjusting section of this Service Manual.Fuel Injection Timing Not Correct
Follow the procedures in the Testing and Adjusting section of this Service Manual.Check Engine Performance
Install the tooling and follow the procedure given in the Road Test section.At this point, the governor fuel settings should be verified. See the Testing and Adjusting section of this Service Manual for the necessary procedures. Also, refer back to the information learned earlier (see Owner/Operator Input section) about the truck specifications and application and judge whether or not the engine is performing as expected or customer expectation is realistic.