101600-3021 ZEXEL 9 400 611 504 BOSCH INJECTION-PUMP ASSEMBLY 9400611504 1016003021 3863862

Information Cross number Calibration Data Calibration Data Ex

Information injection-pump assembly

BOSCH 9 400 611 504 9400611504

ZEXEL 101600-3021 1016003021

KOMATSU 3863862 3863862

Price: query

Buy now
Add to cart Go to cart

Rating:

Buy INJECTION-PUMP ASSEMBLY 101600-3021 zexel genuine, new aftermarket engine parts with delivery

Service parts 101600-3021 INJECTION-PUMP ASSEMBLY:

1. _

2. FUEL INJECTION PUMP 101062-9111

3. GOVERNOR 105404-5571

4. SUPPLY PUMP

5. AUTOM. ADVANCE MECHANIS

6. COUPLING PLATE

7. COUPLING PLATE

8. _

9. _

10. NOZZLE AND HOLDER ASSY

11. Nozzle and Holder

12. Open Pre:MPa(Kqf/cm2) 21.6{220}

13. NOZZLE-HOLDER

14. NOZZLE

15. NOZZLE SET

Include in #1:

101600-3021 as INJECTION-PUMP ASSEMBLY

101692-3381 as _

Cross reference number

BOSCH 9 400 611 504 9400611504

ZEXEL 101600-3021 1016003021

KOMATSU 3863862 3863862

Zexel num

Bosch num

Firm num

Name

101600-3021

9 400 611 504

3863862 KOMATSU

INJECTION-PUMP ASSEMBLY
S6D102E K 14BE INJECTION PUMP ASSY PE6A PE

101600-3021

9 400 611 504

6735711460 KOMATSU

INJECTION-PUMP ASSEMBLY
S6D102E K 14BE INJECTION PUMP ASSY PE6A PE

Calibration Data:

Adjustment conditions

Test oil
1404 Test oil ISO4113 or {SAEJ967d}

Test oil temperature degC 40 40 45

Nozzle and nozzle holder 105780-8140

Bosch type code EF8511/9A

Nozzle 105780-0000

Bosch type code DN12SD12T

Nozzle holder 105780-2080

Bosch type code EF8511/9

Opening pressure MPa 17.2

Opening pressure kgf/cm2 175

Injection pipe
Outer diameter - inner diameter - length (mm) mm 6-2-600

Overflow valve 131424-3420

Overflow valve opening pressure kPa 255 221 289

Overflow valve opening pressure kgf/cm2 2.6 2.25 2.95

Tester oil delivery pressure kPa 157 157 157

Tester oil delivery pressure kgf/cm2 1.6 1.6 1.6

Direction of rotation (viewed from drive side)
Right R

Injection timing adjustment

Direction of rotation (viewed from drive side)
Right R

Injection order 1-5-3-6- 2-4

Pre-stroke mm 2.5 2.45 2.55

Beginning of injection position
Drive side NO.1

Difference between angles 1
Cal 1-5 deg. 60 59.5 60.5

Difference between angles 2
Cal 1-3 deg. 120 119.5 120.5

Difference between angles 3
Cal 1-6 deg. 180 179.5 180.5

Difference between angles 4
Cyl.1-2 deg. 240 239.5 240.5

Difference between angles 5
Cal 1-4 deg. 300 299.5 300.5

Injection quantity adjustment

Adjusting point A

Rack position 11

Pump speed r/min 1250 1250 1250

Average injection quantity mm3/st. 82.5 81.5 83.5

Max. variation between cylinders % 0 -2.5 2.5

Basic *

Fixing the lever *

Injection quantity adjustment_02

Adjusting point C

Rack position 8.6+-0.5

Pump speed r/min 400 400 400

Average injection quantity mm3/st. 8 7 9

Max. variation between cylinders % 0 -15 15

Fixing the rack *

Injection quantity adjustment_03

Adjusting point D

Rack position -

Pump speed r/min 100 100 100

Average injection quantity mm3/st. 75 75 85

Fixing the lever *

Rack limit *

Test data Ex:

Governor adjustment

N:Pump speed R:Rack position (mm) (1)Target notch: K (2)Tolerance for racks not indicated: +-0.05mm. (3)Adjust the secondary timing before adjusting the governor. (4)RACK LIMIT
----------
K=10
----------

Speed control lever angle

F:Full speed I:Idle (1)Stopper bolt setting
----------

----------
a=16deg+-5deg b=33deg+-5deg

Stop lever angle

N:Pump normal S:Stop the pump.
----------

----------
a=0deg+-5deg b=53deg+-5deg

Timing setting

(1)Pump vertical direction (2)Key groove position at No. 1 cylinder's beginning of injection position (at BTDC: aa). (3)Position of the key groove of the No. 1 cylinder at B.T.D.C. bb (fix the governor flyweight at this position for delivery). (4)B.T.D.C.: aa (5)At second timing adjustment, set the camshaft at the * position and tighten the flyweight locknut. (6)Align the flyweight's timing gear position with the lockpin groove and then fully tighten the flyweight to the camshaft. (7)Remove the lock pin and adjust the governor. Reinstall the lock pin to fix the flyweight for delivery.
----------
aa=18deg bb=0deg
----------
a=54deg54min+-3deg b=9deg+-30min

Information:

Illustration 4 g01784824
Right side view of machine (A) Hood and guard group (B) Lines group (Air) (C) Air cleaner
Illustration 5 g01784914
Front view of machineInstallation Procedure
The installation procedure that follows is specific for the listed machine.Diesel Particulate Filter Installation
Illustration 6 g01784177
(2) 331-8935 Bracket (12) 5P-8245 Hard Washer (13) 6V-8149 Nut (14) 8F-6437 Washer (15) 8T-4956 Bolt
Place two new 331-8935 Brackets (2) parallel to each other on top of the hood. Secure the brackets by using four new 8F-6437 Washers (14), four new 5P-8245 Hard Washers (12), four new 6V-8149 Nuts (13) and four new 8T-4956 Bolts (15). Refer to Illustration 6.
Illustration 7 g01784193
(5) 295-3044 Exhaust Support Gp (Lower half) (14) 8F-6437 Washer (15) 8T-4956 Bolt
Install the two lower halves of the new 295-3044 Exhaust Support Gp (5) onto two brackets (2) using four new 8F-6437 Washers (14) and four new 8T-4956 Bolts (15). Refer to Illustration 7.
Illustration 8 g01784213
(1) 331-8928 Diesel Particulate Filter Gp (5a) Clamp As (Upper half) (5b) Bolts (5c) Hard Washers (5d) Weld Nuts
Place 331-8928 Diesel Particulate Filter Gp (1) onto the two lower halves of exhaust support group (5). The weight of the diesel particulate filter group is approximately 43.6 kg (96.1 lb). Refer to Illustration 8.
Install the two upper clamp assemblies (5a) onto the two lower halves of exhaust support group (5) by using four hard washers (5c), four weld nuts (5d) and four bolts (5b). Refer to Illustration 8.
Illustration 9 g01784214
(9) 174-5414 Clamp (11) 255-2899 Tail Pipe As
Install the new 255-2899 Tail Pipe As (11) to the outlet module tube of the diesel particulate filter group. Refer to Illustration 9.
Secure tail pipe assembly (11) to the outlet module tube of diesel particulate filter group by using a new 174-5414 Clamp (9). Refer to Illustration 9.
Illustration 10 g01784215
(3) 331-9047 Filter Tube As (7) 241-6170 Plug (8) 8T-6765 Pipe Plug (10) 209-4589 Clamp
Install the new 331-9047 Filter Tube As (3) to the inlet module tube of the diesel particulate filter group. Refer to Illustration 10.
Secure filter tube assembly (3) to the inlet module tube of the diesel particulate filter group by using one new 209-4589 Clamp (10). Refer to Illustration 10.
Install the new 241-6170 Plug (7) and 8T-6765 Pipe Plug (8) onto the bosses that are provided on filter tube assembly (3). Refer to Illustration 10.
Illustration 11 g01784216
(6) 270-0112 Bellows (10) 209-4589 Clamp
Install the new 270-0112 Bellows (6) to filter tube assembly (3). Refer to Illustration 11.
Secure bellows (6) to filter tube assembly (3) by using one new 209-4589 Clamp (10). Refer to Illustration 11.
Illustration 12 g01784217
(4) 331-8934 Filter Tube (10) 209-4589 Clamp
Install the new 331-8934 Filter Tube (4) into bellows (6). Refer to Illustration 12.
Secure filter tube (4) to bellows (6) by using one new 209-4589 Clamp (10). Refer to Illustration 12.
Connect