101491-9233 ZEXEL INJECTION-PUMP ASSEMBLY Cross 1014919233 sl4713800a


 

Information injection-pump assembly

ZEXEL 101491-9233 1014919233
MAZDA SL4713800A sl4713800a
101491-9233 INJECTION-PUMP ASSEMBLY
Rating:
22
Buy INJECTION-PUMP ASSEMBLY 101491-9233 zexel genuine, new aftermarket engine parts with delivery

Cross reference number

Zexel num
Bosch num
Firm num
Name
101491-9233 
 
SL4713800A  MAZDA
INJECTION-PUMP ASSEMBLY
SL * K




Information:

Use of the Pickup During Wet Conditions
If the pickup becomes wet, it may operate intermittently or not at all. Although the pickup is water resistant, it is not waterproof. Water spray from rain or other sources may cause the pickup to stop producing an output signal.If this happens, the pickup should be removed from the engine and allowed to dry out thoroughly. If necessary, the pickup can be dried in an oven at approximately 50°C (122°F). After drying, the pickup should operate correctly.If it is not possible to keep the pickup dry, use the following procedure: If the pickup must be used during wet conditions, it may be possible to protect it from moisture by using a water displacing spray such as WD-40®.Remove the pickup from the engine. Thoroughly spray the pickup from all directions. Make sure the pickup is completely covered with the spray. Reinstall the pickup on the engine and check its operation.When water first contacts the pickup, the unit may stop working temporarily, but will start working again after the water has been displaced by the solution. If necessary, spray the solution on the pickup after installation on the injection line.Permanent Installation on the Engine
If the pickup is to be permanently installed on the engine, install the pickup on the fuel injection line in the usual manner. Make sure that the thumbscrew is hand tightened securely, but not over tightened. Run the engine and check the operation of the pickup.Make sure that the pickup and line are clean and dry. If the pickup is working correctly, use a can of spray paint to thoroughly paint the pickup from all directions. Several coats should be applied. Let the paint dry thoroughly before operating the engine.Checking the Operation of the Amplifier and Pickup
(1) 6V2100 Multitach. (2) 5P9698 Calibrator. (3) 5P7366 Power Cable. (4) Digital Multimeter. (5) Screwdriver. (6) 6V6152 Adapter. Screwdriver (5) should have a blade approximately 150 mm (6 in) long with 6 mm (.25 in) diameter shaft of round bare metal (not anodized or insulated).The 6V6152 Adapter (6) is a phono plug-to-BNC connector. Modifications must be made to the 5P9698 Calibrator (2). Refer to Special Instruction, SMHS7504-01.Checking the 4C6812 Amplifier
(1) 6V6152 Adapter Plug. (2) 5P9698 Calibrator. (3) 4C6812 Amplifier. (4) Connector. (5) 5P7366 Power Cable. (6) Knob. (7) Battery Indicator. (8) No Input Signal Light.1. Install 6V6152 Adapter Plug (1) on the end of the output cable on 5P9698 Calibrator (2). Plug the adapter into 4C6812 Amplifier (3).2. Check the operation of the multitach being used by performing the CHECKING PHOTO OPERATION test procedure contained in Special Instruction SEHS7807. (This is to ensure it is operating correctly on PHOTO operation.)3. Plug connector (4), on the end of the amplifier output cable, into the PH (photo) connector on the multitach. Attach 5P7366 Power Cable (5) to the multitach and to a suitable power source. Refer to SEHS7807.4. Program the multitach for .5 P/REV and to read R/MIN on the PH (photo) input. Turn knob (6) on

Have questions with 101491-9233?





Group cross 101491-9233 ZEXEL

Nissan-Diesel 

 
1671390063 
INJECTION-PUMP ASSEMBLY
FD33

Mazda 

 
 
INJECTION-PUMP ASSEMBLY
SL
 
SL4413800 
INJECTION-PUMP ASSEMBLY
SL
 
 
INJECTION-PUMP ASSEMBLY

Mazda 

 
SL4413800A 
INJECTION-PUMP ASSEMBLY
SL
 
 
INJECTION-PUMP ASSEMBLY
SL
 
SL4613800 
INJECTION-PUMP ASSEMBLY
SL
 
 
INJECTION-PUMP ASSEMBLY

Mazda 

 
SL4613800A 
INJECTION-PUMP ASSEMBLY
SL
 
 
INJECTION-PUMP ASSEMBLY
SL
 
SL4713800 
INJECTION-PUMP ASSEMBLY
SL
 
 
INJECTION-PUMP ASSEMBLY

Mazda 

101491-9233  
 
SL4713800A 
INJECTION-PUMP ASSEMBLY
SL
 
 
INJECTION-PUMP ASSEMBLY
SL
 
SL4813800 
INJECTION-PUMP ASSEMBLY
SL
 
 
INJECTION-PUMP ASSEMBLY

Mazda 

9 400 614 333 
SL4813800A 
INJECTION-PUMP ASSEMBLY
SL

Nissan-Diesel 

9 400 610 090 
1679090211 
INJECTION-PUMP ASSEMBLY
FD33
 
1671290115 
INJECTION-PUMP ASSEMBLY
FD33

Mazda 

 
 
INJECTION-PUMP ASSEMBLY
P630K
 
 
INJECTION-PUMP ASSEMBLY
P630K
 
Z02SL5013800 
INJECTION-PUMP ASSEMBLY
P630K
 
 
INJECTION-PUMP ASSEMBLY
P630K
 
 
INJECTION-PUMP ASSEMBLY
P630K
 
 
INJECTION-PUMP ASSEMBLY

Mazda 

9 400 614 334 
SL5013800B 
INJECTION-PUMP ASSEMBLY
P630K
 
 
INJECTION-PUMP ASSEMBLY
P630K
 
 
INJECTION-PUMP ASSEMBLY
P630K
 
Z02SL5113800 
INJECTION-PUMP ASSEMBLY
P630K
 
 
INJECTION-PUMP ASSEMBLY
P630K
 
 
INJECTION-PUMP ASSEMBLY
P630K
 
 
INJECTION-PUMP ASSEMBLY

Mazda 

9 400 614 335 
SL5113800B 
INJECTION-PUMP ASSEMBLY
P630K
 
Z02SL5213800 
INJECTION-PUMP ASSEMBLY
P630K
Back to top