Information injection-pump assembly
ZEXEL
101491-0552
1014910552
ISUZU
8970315620
8970315620
Rating:
Cross reference number
ZEXEL
101491-0552
1014910552
ISUZU
8970315620
8970315620
Zexel num
Bosch num
Firm num
Name
Calibration Data:
Adjustment conditions
Test oil
1404 Test oil ISO4113 or {SAEJ967d}
1404 Test oil ISO4113 or {SAEJ967d}
Test oil temperature
degC
40
40
45
Nozzle and nozzle holder
105780-8140
Bosch type code
EF8511/9A
Nozzle
105780-0000
Bosch type code
DN12SD12T
Nozzle holder
105780-2080
Bosch type code
EF8511/9
Opening pressure
MPa
17.2
Opening pressure
kgf/cm2
175
Injection pipe
Outer diameter - inner diameter - length (mm) mm 6-2-600
Outer diameter - inner diameter - length (mm) mm 6-2-600
Overflow valve
131424-4920
Overflow valve opening pressure
kPa
127
107
147
Overflow valve opening pressure
kgf/cm2
1.3
1.1
1.5
Tester oil delivery pressure
kPa
157
157
157
Tester oil delivery pressure
kgf/cm2
1.6
1.6
1.6
Direction of rotation (viewed from drive side)
Right R
Right R
Injection timing adjustment
Direction of rotation (viewed from drive side)
Right R
Right R
Injection order
1-3-4-2
Pre-stroke
mm
3.8
3.75
3.85
Rack position
After adjusting injection quantity. R=A
After adjusting injection quantity. R=A
Beginning of injection position
Drive side NO.1
Drive side NO.1
Difference between angles 1
Cal 1-3 deg. 90 89.5 90.5
Cal 1-3 deg. 90 89.5 90.5
Difference between angles 2
Cal 1-4 deg. 180 179.5 180.5
Cal 1-4 deg. 180 179.5 180.5
Difference between angles 3
Cyl.1-2 deg. 270 269.5 270.5
Cyl.1-2 deg. 270 269.5 270.5
Injection quantity adjustment
Adjusting point
-
Rack position
12.2
Pump speed
r/min
950
950
950
Average injection quantity
mm3/st.
52.4
50.8
54
Max. variation between cylinders
%
0
-2.5
2.5
Basic
*
Fixing the rack
*
Standard for adjustment of the maximum variation between cylinders
*
Injection quantity adjustment_02
Adjusting point
H
Rack position
9.9+-0.5
Pump speed
r/min
325
325
325
Average injection quantity
mm3/st.
13.3
12
14.6
Max. variation between cylinders
%
0
-14
14
Fixing the rack
*
Standard for adjustment of the maximum variation between cylinders
*
Injection quantity adjustment_03
Adjusting point
A
Rack position
R1(12.2)
Pump speed
r/min
950
950
950
Average injection quantity
mm3/st.
52.4
51.4
53.4
Basic
*
Fixing the lever
*
Injection quantity adjustment_04
Adjusting point
B
Rack position
R1(12.2)
Pump speed
r/min
1750
1750
1750
Average injection quantity
mm3/st.
65.9
61.9
69.9
Fixing the lever
*
Injection quantity adjustment_05
Adjusting point
I
Rack position
-
Pump speed
r/min
100
100
100
Average injection quantity
mm3/st.
86
70
102
Fixing the lever
*
Timer adjustment
Pump speed
r/min
1525--
Advance angle
deg.
0
0
0
Remarks
Start
Start
Timer adjustment_02
Pump speed
r/min
1475
Advance angle
deg.
0.3
Timer adjustment_03
Pump speed
r/min
1775
Advance angle
deg.
4.5
4
5
Remarks
Finish
Finish
Test data Ex:
Governor adjustment
N:Pump speed
R:Rack position (mm)
(1)Torque cam stamping: T1
(2)Tolerance for racks not indicated: +-0.05mm.
(3)At delivery (at R = A, N = N1)
----------
T1=F40 N1=100r/min
----------
----------
T1=F40 N1=100r/min
----------
Speed control lever angle
F:Full speed
I:Idle
(1)Use the hole at R = aa
(2)Set the idle side stopper bolt so that speed = bb and rack position = cc (at delivery).
(3)Stopper bolt set position 'H'
----------
aa=50mm bb=100r/min cc=R1(12.2)mm
----------
a=(23.5deg) b=27deg+-5deg c=(36deg)+-3deg
----------
aa=50mm bb=100r/min cc=R1(12.2)mm
----------
a=(23.5deg) b=27deg+-5deg c=(36deg)+-3deg
Stop lever angle
N:Pump normal
S:Stop the pump.
(1)Use the hole at R = aa
----------
aa=64mm
----------
a=45deg+-5deg b=29deg+-5deg
----------
aa=64mm
----------
a=45deg+-5deg b=29deg+-5deg
0000001501 I/P WITH LOAD PLUNGER ADJ
Plunger assembly number: PL (stamping: ST)
1. Adjustment procedures
(1)Insert the pre-stroke adjusting shims L1 for each cylinder.
(2)Adjust injection quantity.(max. var. bet. cyl. idling a1, full a2)
(3)At basic point A, adjust so that the pre-stroke is L2.
(4)Reconfirm the injection quantity.
----------
PL=131154-1820 ST=A260 L1=1mm L2=3.8+-0.05mm a1=+-14% a2=+-2.5%
----------
----------
PL=131154-1820 ST=A260 L1=1mm L2=3.8+-0.05mm a1=+-14% a2=+-2.5%
----------
Timing setting
(1)Pump vertical direction
(2)Position of gear mark 'CC' at No 1 cylinder's beginning of injection
(3)B.T.D.C.: aa
(4)-
----------
aa=15deg
----------
a=(100deg)
----------
aa=15deg
----------
a=(100deg)
Information:
Cylinder Heads Without Guides
Cylinder Heads With Guides New cylinder heads have been introduced on the 4.236 engine. The new heads have replaceable valve guides. The differences between the earlier and current heads are explained below. The change became effective at engine serial number LD70178U040236M and up. The engine serial number is located above the fuel injection pump on the block.(1) Outer spring: Length under test force ... 27.4 mm (1.08 in)Test force ... 180 9 N (40 2 lb)Free length after test ... 45.2 mm (1.78 in)(Damper coils of spring go toward cylinder head).(2) Inner spring: Length under test force ... 23.88 mm (.940 in)Test force ... 69 9 N (15.4 2 lb)Free length after test ... 39.6 mm (1.56 in)(Damper coils of spring go toward cylinder head).Earlier Cylinder Heads Without Removable Guides
(3) Exhaust valve stem diameter ... 9.449 to 9.469 mm (.372 to .3728 in) Valves are available in stem oversizes of 0.08, 0.38 and 0.76 mm (.003, .015 and .030 in).Exhaust valve overall length ... 123.11 to 123.52 mm (4.847 to 4.863 in)Bore in cylinder head for valve ... 9.506 to 9.531 mm (.37425 to .37525 in)Clearance between valve stem and bore ... 0.0368 to 0.0826 mm (.00145 to .00325 in)Maximum permissible clearance between valve stem and bore ... 0.15 mm (.006 in)(4) Intake valve stem diameter ... 9.462 to 9.487 mm (.3725 to .3735 in) Valves are available in stem oversizes of 0.08, 0.38 and 0.76 mm (.003, .015 and .030 in).Intake valve overall length ... 122.71 to 123.11 mm (4.831 to 4.847 in)Bore in cylinder head for valve ... 9.506 to 9.531 mm (.37425 to .37525 in)Clearance between valve stem and bore ... 0.0191 to 0.0699 mm (.00075 to .00275 in)Maximum permissible clearance between valve stem and bore ... 0.13 mm (.005 in)Current Cylinder Heads With Removable Guides
(5) Valve guides: Inside diameter ... 9.507 to 9.543 mm (.3743 to .3757 in)Outside diameter ... 15.921 to 15.933 mm (.6268 to .6273 in)Parent bore diameter in cylinder head for valve guide ... 15.867 to 15.893 mm (.6247 to .6257 in)Interference fit of guide in cylinder head ... 0.028 to 0.066 mm (.0011 to .0026 in)Overall length of guide:Intake ... 57.94 mm (2.281 in)Exhaust ... 61.11 mm (2.406 in)Projection of guide above valve spring recess ... 15.09 mm (.594 in)(6) Exhaust valve stem diameter ... 9.449 to 9.468 mm (.372 to .3728 in) Clearance of valve in guide ... 0.058 to 0.119 mm (.0023 to .0047 in)Maximum permissible clearance of valve in guide ... 0.13 mm (.005 in)Exhaust valve overall length ... 123.11 to 123.52 mm (4.847 to 4.863 in)(7) Intake valve stem diameter ... 9.462 to 9.487 mm (.3725 to .3735 in) Clearance of valve in guide ... 0.058 to 0.119 mm (.0023 to .0047 in)Maximum permissible clearance of valve in guide ... 0.13 mm (.006 in)Intake valve overall length ... 122.71 to 123.11 mm (4.831 to 4.847 in)All Cylinder Heads
(8) Exhaust valve