101452-3093 ZEXEL 9 400 610 194 BOSCH INJECTION-PUMP ASSEMBLY 9400610194 1014523093 6204721431

Information Cross number Calibration Data Calibration Data Ex

Information injection-pump assembly

BOSCH 9 400 610 194 9400610194

ZEXEL 101452-3093 1014523093

KOMATSU 6204721431 6204721431

Price: query

Buy now
Add to cart Go to cart

Rating:

Buy INJECTION-PUMP ASSEMBLY 101452-3093 zexel genuine, new aftermarket engine parts with delivery

Service parts 101452-3093 INJECTION-PUMP ASSEMBLY:

1. _

2. FUEL INJECTION PUMP 101045-8090

3. GOVERNOR 105400-7690

4. SUPPLY PUMP 105220-5610

5. AUTOM. ADVANCE MECHANIS

6. COUPLING PLATE

7. COUPLING PLATE

8. _

9. _

10. NOZZLE AND HOLDER ASSY 105141-2520

11. Nozzle and Holder 6202-12-3100

12. Open Pre:MPa(Kqf/cm2) 11.8{120}

13. NOZZLE-HOLDER 105071-1450

14. NOZZLE 105000-1770

15. NOZZLE SET

Include in #1:

101452-3093 as INJECTION-PUMP ASSEMBLY

101601-4161 as _

Cross reference number

BOSCH 9 400 610 194 9400610194

ZEXEL 101452-3093 1014523093

KOMATSU 6204721431 6204721431

Zexel num

Bosch num

Firm num

Name

101452-3093

9 400 610 194

6204721431 KOMATSU

INJECTION-PUMP ASSEMBLY
4D95L K 14BC INJECTION PUMP ASSY PE4A,5A, PE

Calibration Data:

Adjustment conditions

Test oil
1404 Test oil ISO4113 or {SAEJ967d}

Test oil temperature degC 40 40 45

Nozzle and nozzle holder 105780-8140

Bosch type code EF8511/9A

Nozzle 105780-0000

Bosch type code DN12SD12T

Nozzle holder 105780-2080

Bosch type code EF8511/9

Opening pressure MPa 17.2

Opening pressure kgf/cm2 175

Injection pipe
Outer diameter - inner diameter - length (mm) mm 6-2-600

Tester oil delivery pressure kPa 157 157 157

Tester oil delivery pressure kgf/cm2 1.6 1.6 1.6

Direction of rotation (viewed from drive side)
Right R

Injection timing adjustment

Direction of rotation (viewed from drive side)
Right R

Injection order 1-2-4-3

Pre-stroke mm 1.5 1.45 1.55

Beginning of injection position
Drive side NO.1

Difference between angles 1
Cyl.1-2 deg. 90 89.5 90.5

Difference between angles 2
Cal 1-4 deg. 180 179.5 180.5

Difference between angles 3
Cal 1-3 deg. 270 269.5 270.5

Injection quantity adjustment

Adjusting point A

Rack position 12

Pump speed r/min 900 900 900

Average injection quantity mm3/st. 45.8 44.8 46.8

Max. variation between cylinders % 0 -2.5 2.5

Basic *

Fixing the lever *

Injection quantity adjustment_02

Adjusting point -

Rack position 8.3+-0.5

Pump speed r/min 400 400 400

Average injection quantity mm3/st. 11 10 12

Max. variation between cylinders % 0 -15 15

Fixing the rack *

Remarks
Adjust only variation between cylinders; adjust governor according to governor specifications.

Test data Ex:

Governor adjustment

N:Pump speed R:Rack position (mm) (1)Target notch: K (2)RACK CAP: R1 (3)The torque control spring must does not have a set force. (4)Rack difference between N = N1 and N = N2 (5)Idle sub spring setting: L1.
----------
K=10 R1=(17.5)mm N1=900r/min N2=500r/min L1=8-0.5mm
----------

Speed control lever angle

F:Full speed I:Idle (1)Set the pump speed at aa (2)Set the pump speed at bb. (3)Stopper bolt setting (4)Stopper bolt setting
----------
aa=750r/min bb=955r/min
----------
a=(1deg)+-5deg b=(6deg)+-5deg c=(23deg)+-5deg

Stop lever angle

N:Pump normal S:Stop the pump. (1)No return spring
----------

----------
a=43.5deg+-5deg b=53deg+-5deg

Timing setting

(1)Pump vertical direction (2)Position of key groove at No 1 cylinder's beginning of injection (3)Stamp aligning marks on the pump housing flange. (4)-
----------

----------
a=46deg18min+-3deg b=13deg42min+-30min

Information:

Do not operate or work on this product unless you have read and understood the instruction and warnings in the relevant Operation and Maintenance Manuals and relevant service literature. Failure to follow the instructions or heed the warnings could result in injury or death. Proper care is your responsibility.
To improve the reliability and performance of its products, Cat Reman has replaced the entire product line of HI315B Injectors with a version that includes a pre-screen that will capture a portion of the debris trapped in the fuel system during service. The pre-screen will not change the fit, form, or function of the injectors. If a Reman injector order has been filled with new injectors, the new injectors will not have the screen. Injectors both with and without the pre-screen can be used interchangeably.
Illustration 1 g06334704
Table 1
H1315B Injectors
New Part Number Reman Part Number
387-9426 20R-8071
387-9427 20R-8066
387-9428 20R-8059
387-9429 20R-8058
387-9430 20R-8057
387-9431 20R-8069
387-9432 20R-8065
387-9433 20R-8064
387-9434 20R-8063
387-9436 20R-8068
387-9437 20R-8062
387-9438 20R-8060
387-9439 20R-8061
387-9440 20R-8070
387-9441 20R-8067