101433-9690 ZEXEL INJECTION-PUMP ASSEMBLY Calibration Data 1014339690

Information Cross number Calibration Data Calibration Data Ex

Information injection-pump assembly

ZEXEL 101433-9690 1014339690

Price: query

Buy now
Add to cart Go to cart

Rating:

Buy INJECTION-PUMP ASSEMBLY 101433-9690 zexel genuine, new aftermarket engine parts with delivery

Service parts 101433-9690 INJECTION-PUMP ASSEMBLY:

1. _

2. FUEL INJECTION PUMP 101043-8420

3. GOVERNOR 105410-6651

4. SUPPLY PUMP 105220-4630

5. AUTOM. ADVANCE MECHANIS 105622-0910

6. COUPLING PLATE

7. COUPLING PLATE

8. _

9. _

10. NOZZLE AND HOLDER ASSY 105141-1800

11. Nozzle and Holder 16600-90019

12. Open Pre:MPa(Kqf/cm2) 9.8{100}

13. NOZZLE-HOLDER 105071-1240

14. NOZZLE

105000-1010

15. NOZZLE SET

Include in #1:

101433-9690 as INJECTION-PUMP ASSEMBLY

Include in #2:

105856-1714 as _

Cross reference number

ZEXEL 101433-9690 1014339690

Zexel num

Bosch num

Firm num

Name

101433-9690

INJECTION-PUMP ASSEMBLY
14BC PE4A,5A, PE

Calibration Data:

Adjustment conditions

Test oil
1404 Test oil ISO4113 or {SAEJ967d}

Test oil temperature degC 40 40 45

Nozzle and nozzle holder 105780-8140

Bosch type code EF8511/9A

Nozzle 105780-0000

Bosch type code DN12SD12T

Nozzle holder 105780-2080

Bosch type code EF8511/9

Opening pressure MPa 17.2

Opening pressure kgf/cm2 175

Injection pipe
Outer diameter - inner diameter - length (mm) mm 6-2-600

Tester oil delivery pressure kPa 157 157 157

Tester oil delivery pressure kgf/cm2 1.6 1.6 1.6

Direction of rotation (viewed from drive side)
Right R

Injection timing adjustment

Direction of rotation (viewed from drive side)
Right R

Injection order 1-3-4-2

Pre-stroke mm 2.3 2.25 2.35

Beginning of injection position
Drive side NO.1

Difference between angles 1
Cal 1-3 deg. 90 89.5 90.5

Difference between angles 2
Cal 1-4 deg. 180 179.5 180.5

Difference between angles 3
Cyl.1-2 deg. 270 269.5 270.5

Injection quantity adjustment

Adjusting point A

Rack position 14.5

Pump speed r/min 600 600 600

Average injection quantity mm3/st. 33.3 32.3 34.3

Max. variation between cylinders % 0 -2.5 2.5

Basic *

Fixing the lever *

Injection quantity adjustment_02

Adjusting point B

Rack position 13.8

Pump speed r/min 1550 1550 1550

Average injection quantity mm3/st. 35.5 34 37

Max. variation between cylinders % 0 -4 4

Fixing the lever *

Injection quantity adjustment_03

Adjusting point C

Rack position 10.8+-0. 5

Pump speed r/min 300 300 300

Average injection quantity mm3/st. 7.5 6.4 8.6

Max. variation between cylinders % 0 -15 15

Fixing the rack *

Remarks
Adjust only variation between cylinders; adjust governor according to governor specifications.

Timer adjustment

Pump speed r/min 550--

Advance angle deg. 0 0 0

Remarks
Start

Timer adjustment_02

Pump speed r/min 500

Advance angle deg. 0.5

Timer adjustment_03

Pump speed r/min 900

Advance angle deg. 1.8 1.3 2.3

Timer adjustment_04

Pump speed r/min 1200

Advance angle deg. 3.3 2.8 3.8

Timer adjustment_05

Pump speed r/min 1500

Advance angle deg. 5 4.5 5.5

Remarks
Finish

Test data Ex:

Governor adjustment

N:Pump speed R:Rack position (mm) (1)Target notch: K
----------
K=15
----------

Speed control lever angle

F:Full speed I:Idle S:Stop
----------

----------
a=28deg+-5deg b=43deg+-5deg c=32deg+-3deg

Stop lever angle

N:Pump normal S:Stop the pump.
----------

----------
a=19deg+-5deg b=53deg+-5deg

0000001501 GOV FULL LOAD ADJUSTMENT

Title1:Full load stopper adjustment Title2:Governor set speed LABEL1:Distinguishing LABEL2:Pump speed (r/min) LABEL3:Ave. injection quantity (mm3/st) LABEL4:Max. var. bet. cyl. LABEL5:Remarks LABEL6:Distinguishing LABEL7:Governor set speed (r/min) LABEL8:Maximum no-load speed (r/min) LABEL9:Remarks (1)Adjustment conditions are the same as those for measuring injection quantity. (2)At high idle rack position L
----------
L=9mm
----------
a1=A a2=B a3=C a4=D a5=- a6=- r1=800r/min r2=750r/min r3=600r/min r4=600r/min r5=- r6=- Q1=37+-1mm3/st Q2=35+-1mm3/st Q3=33.3+-1mm3/st Q4=27.3+-1mm3/st Q5=- Q6=- c1=+-2.5% c2=+-2.5% c3=+-2.5% c4=+-2.5% c5=- c6=- a7=32 a8=31 a9=30 a10=29 a11=28 a12=27 a13=26 a14=25 a15=24 a16=23 a17=22 a18=21 a19=20 a20=19 a21=18 a22=17 a23=16 a24=15 a25=- a26=- a27=- a28=- r7=1600r/min r8=1550r/min r9=1500r/min r10=1450r/min r11=1400r/min r12=1350r/min r13=1300r/min r14=1250r/min r15=1200r/min r16=1150r/min r17=1100r/min r18=1050r/min r19=1000r/min r20=950r/min r21=900r/min r22=850r/min r23=800r/min r24=750r/min r25=- r26=- r27=- r28=- R7=1720+-40r/min R8=1665+-38r/min R9=1610+-37r/min R10=1555+-36r/min R11=1505+-35r/min R12=1450+-33r/min R13=1395+-32r/min R14=1340+-31r/min R15=1290+-30r/min R16=1235+-28r/min R17=1180+-27r/min R18=1130+-26r/min R19=1075+-25r/min R20=1020+-23r/min R21=965+-22r/min R22=915+-22r/min R23=860+-20r/min R24=805+-18r/min R25=- R26=- R27=- R28=-

Timing setting

(1)Pump vertical direction (2)Position of gear mark 'Y' at No 1 cylinder's beginning of injection (3)B.T.D.C.: aa (4)-
----------
aa=20deg
----------
a=(130deg)

Information:

(1) Remove former fuel injection lines (1), the clamps and through-the-cover fuel line adapters (2) from the engine; these parts will not be needed again. Install 8M4437 Seals on twelve 1W6777 Adapters (3). Put engine oil on the seals and install the adapters in valve cover base assemblies (4) where adapters (2) were removed. Fasten the adapters to bases (4) with two 5N5365 Locks on each and the former nuts. Connect former fuel lines (5) to adapters (3) and the former fuel nozzle adapters. (2) Install a 2W2500 Washer (7) and a 6V6579 Seal (8) on each adapter (3). Install a 5P9267 Seal on each injector pump; put diesel fuel on the seals before installation. Loosely install fuel injection line assemblies: number "6" (9), number "12" (10), number "4" (11), number "2" (12), number "10" (13) and number "8" (14) on the right side of the engine between the fuel injection pumps and adapters (3). See the above chart for the correct part number of the fuel lines. Remove two bolts and install 5N5370 Bracket (15) and 5N5374 Clamp (16) where the bolts were removed. Fasten the fuel injection lines to bracket (15) with two 5N5369 Dampers, a 5N5371 Clamp and two 2W7884 Bolt Assemblies. Fasten the fuel injection lines to clamp (16) with two 5N5373 Dampers, a 5N5372 Clamp and two 2W7884 Bolts. Use 5N5957 and 5N5958 Clamps, two 5N5956 Dampers and a 2W7884 Bolt Assembly to fasten the fuel lines together at (A). Use 5N5376 and 5N5377 Clamps, two 5N5375 Dampers and three 2W7884 Bolt Assemblies to fasten the fuel lines together at (B). Tighten the bolt assemblies to 10 N m (7 lb.ft.) torque. Tighten nuts (17) on each end of the fuel injection lines to 40 7 N m (35 5 lb.ft.) torque, then tighten nuts (18).(3) Loosely install fuel injection line assemblies; number "11" (19), number "3" (20), number "7" (21), number "9" (22), number "5" (23) and number "1" (24) on the left side of the engine between adapters (3) and the fuel injection pump as shown. Remove a bolt and install 5N5370 Bracket (25) where the bolt was removed. Fasten the fuel lines to bracket (25) with two 5N5369 Dampers, a 5N5371 Clamp and two 2W7884 Bolts. On engines equipped with aftercooler, fasten 5N5379 Plate (26) to an existing bolt on the aftercooler. Fasten the fuel injection lines to plate (26) with two 5N5378 Dampers, a 5N5374 Clamp and two 2W7884 Bolt Assemblies. Use two 5N5376 and 5N5377 Clamps, four 5N5375 Dampers and four 2W7884 Bolt Assemblies to fasten the fuel lines together at locations (C). If the engine does not have an aftercooler, use 5N5957 and 5N5958 Clamps, two 5N5956 Dampers and a 2W7884 Bolt Assembly to fasten the fuel injection lines together at (D). Tighten the fuel lines as shown in step 2.2W5100 Fuel Lines Drain Group
(1) Install a 9L8496 Tee (1) in each adapter (2). Connect tees (1) together with ten 5N5940 Tube Assemblies (3).