101433-9040 ZEXEL INJECTION-PUMP ASSEMBLY Calibration Data 1014339040 16700v0601

Information Cross number Calibration Data Calibration Data Ex

Information injection-pump assembly

ZEXEL 101433-9040 1014339040

NISSAN-DIESEL 16700V0601 16700v0601

Price: query

Buy now
Add to cart Go to cart

Rating:

Buy INJECTION-PUMP ASSEMBLY 101433-9040 zexel genuine, new aftermarket engine parts with delivery

Service parts 101433-9040 INJECTION-PUMP ASSEMBLY:

1. _

2. FUEL INJECTION PUMP 101043-8450

3. GOVERNOR 105542-3091

4. SUPPLY PUMP

105220-5001

5. AUTOM. ADVANCE MECHANIS 105622-0550

6. COUPLING PLATE

7. COUPLING PLATE

8. _

9. _

10. NOZZLE AND HOLDER ASSY 105141-1881

11. Nozzle and Holder 16600-20053

12. Open Pre:MPa(Kqf/cm2) 9.8{100}

13. NOZZLE-HOLDER 105071-1241

14. NOZZLE

105000-1080

15. NOZZLE SET

Include in #1:

101433-9040 as INJECTION-PUMP ASSEMBLY

106669-4000 as _

Cross reference number

ZEXEL 101433-9040 1014339040

NISSAN-DIESEL 16700V0601 16700v0601

Zexel num

Bosch num

Firm num

Name

101433-9040

16700V0601 NISSAN-DIESEL

INJECTION-PUMP ASSEMBLY
SD20 * K

Calibration Data:

Adjustment conditions

Test oil
1404 Test oil ISO4113 or {SAEJ967d}

Test oil temperature degC 40 40 45

Nozzle and nozzle holder 105780-8140

Bosch type code EF8511/9A

Nozzle 105780-0000

Bosch type code DN12SD12T

Nozzle holder 105780-2080

Bosch type code EF8511/9

Opening pressure MPa 17.2

Opening pressure kgf/cm2 175

Injection pipe
Outer diameter - inner diameter - length (mm) mm 6-2-600

Tester oil delivery pressure kPa 157 157 157

Tester oil delivery pressure kgf/cm2 1.6 1.6 1.6

Direction of rotation (viewed from drive side)
Right R

Injection timing adjustment

Direction of rotation (viewed from drive side)
Right R

Injection order 1-3-4-2

Pre-stroke mm 2.3 2.25 2.35

Beginning of injection position
Drive side NO.1

Difference between angles 1
Cal 1-3 deg. 90 89.5 90.5

Difference between angles 2
Cal 1-4 deg. 180 179.5 180.5

Difference between angles 3
Cyl.1-2 deg. 270 269.5 270.5

Injection quantity adjustment

Adjusting point A

Rack position 11.6

Pump speed r/min 800 800 800

Average injection quantity mm3/st. 34 33.1 34.9

Max. variation between cylinders % 0 -2.5 2.5

Basic *

Fixing the rack *

Injection quantity adjustment_02

Adjusting point B

Rack position 10.6

Pump speed r/min 1700 1700 1700

Average injection quantity mm3/st. 36.3 34.8 37.8

Max. variation between cylinders % 0 -4 4

Fixing the rack *

Injection quantity adjustment_03

Adjusting point C

Rack position 6

Pump speed r/min 1700 1700 1700

Average injection quantity mm3/st. 8 7.2 8.8

Max. variation between cylinders % 0 -7.5 7.5

Fixing the rack *

Injection quantity adjustment_04

Adjusting point D

Rack position 7.7

Pump speed r/min 300 300 300

Average injection quantity mm3/st. 7.5 6.4 8.6

Max. variation between cylinders % 0 -15 15

Fixing the rack *

Injection quantity adjustment_05

Adjusting point -

Rack position -

Pump speed r/min 800 800 800

Average injection quantity mm3/st. 34 33.5 34.5

Remarks
Smoke setting

Timer adjustment

Pump speed r/min 500

Advance angle deg. 0.3

Timer adjustment_02

Pump speed r/min 550

Advance angle deg. 0.5

Timer adjustment_03

Pump speed r/min 800

Advance angle deg. 0.7 0.2 1.2

Timer adjustment_04

Pump speed r/min 1000

Advance angle deg. 1.4 0.9 1.9

Timer adjustment_05

Pump speed r/min 1200

Advance angle deg. 2.3 1.8 2.8

Timer adjustment_06

Pump speed r/min 1400

Advance angle deg. 3.3 2.8 3.8

Timer adjustment_07

Pump speed r/min 1650

Advance angle deg. 5 4.5 5.5

Remarks
Finish

Test data Ex:

Governor adjustment

N:Pump speed R:Rack position (mm) P:Negative pressure (1)Pneumatic governor (2)Mechanical governor (3)Acting negative pressure: P1 (4)RACK LIMIT: RAL (5)Beginning of idle sub spring operation: L1 (6)Injection quantity Q = Q1 or less
----------
P1=3.24+-0.2kPa(330+-20mmAq) RAL=17mm L1=7.5+0.3mm Q1=3mm3/st
----------

Speed control lever angle

F:Full speed N:Normal S:Stop
----------

----------
a=4.5deg+-5deg b=13deg+-5deg c=19.5deg+-3deg

Timing setting

(1)Pump vertical direction (2)Position of gear mark 'Y' at No 1 cylinder's beginning of injection (3)- (4)-
----------

----------
a=(130deg)

Information:

Right Side (6 Cylinder Shown)(1) Depth that cup plugs are installed (measured from block face to top edge of plug) ... 1.25 0.25 mm (.049 .010 in)(2) Distance all sleeves extend from top face ... 14 2 mm (.55 .08 in)(3) Distance two large dowels extend from rear face ... 12.0 0.5 mm (.47 .02 in)(4) Distance two small dowels extend from rear face ... 8.0 0.5 mm (.31 .02 in)(5) Distance all dowels extend from front face ... 8.0 0.5 mm (.31 .02 in)
View A-A (Rear Face)(6) Bores in block for all camshaft bearings except front bearing ... 69.000 0.038 mm (2.7165 .0015 in)(7) Locate bearing oil hole for all camshaft bearings (except front bearing) at top of bore.
Front Face(8) Bore in block for front camshaft bearing ... 70.000 0.025 mm (2.7559 .0010 in)(9) Front camshaft bearing joint location.(10) Front camshaft bearing oil hole. Install front camshaft bearing with bearing oil hole (10) aligned with oil hole in block and bearing joint (9) positioned as shown.(11) Width of main bearing cap ... 159.995 0.020 mm (6.2990 .0008 in) Width of cylinder block for main bearing cap ... 160.000 0.018 mm (6.2992 .0007 in)(12) Bore in block for main bearings ... 95.000 0.013 mm (3.7402 .0005 in)(13) Main bearing cap bolts. Install as follows: Install bearing caps with sequence number to the right, 1 through 5 (for 4 cylinder) or 1 through 7 (for 6 cylinder), front to rear.a. Before assembly, put 2P2506 Thread Lubricant on the bolt threads and washer face.b. Tighten both bolts of each bearing cap to a torque of ... 54 7 N m (40 5 lb ft)c. Then tighten bolts an additional ... 90 5 degrees (1/4 turn)(14) Location of bearing cap sequence number.(15) Dimension from centerline of crankshaft bore to pan rail ... 110.00 mm (4.331 in)(16) Dimension from centerline of crankshaft bore to top of block ... 322.00 .017 mm (12.677 .0007 in)(17) Cylinder bore size ... 105.025 .025 mm (4.1348 .0010 in) Bore size must be checked with a 4C4377 Cylinder Head Stress Plate and gasket installed. Refer to Installation Of 7C6208 Cylinder Sleeve, Special Instruction Form No. SEHS9047. (18) Piston cooling jet. Check piston cooling jets by inserting a 1.3 mm (.05 in) diameter drill rod into jet. Rod must pass through a 5.0 mm (.20 in) diameter circle in location (A) and a 13 mm (.51 in) diameter circle in location (B). Dimension (C) is 25.9 mm (1.02 in). Dimension (D) is 33.4 mm (1.31 in). Dimension (E) is 26.95 mm (1.061 in). Dimension (F) is 9.8 mm (.39 in). Dimension (G) is 50 mm (2.0 in). Distance four sleeves (19) extend from side face ... 5.0 0.5 mm (.20 .02 in)