Information injection-pump assembly
BOSCH
9 400 614 115
9400614115
ZEXEL
101432-0990
1014320990
ISUZU
8943619920
8943619920
Rating:
Include in #2:
104266-5002
as _
Cross reference number
BOSCH
9 400 614 115
9400614115
ZEXEL
101432-0990
1014320990
ISUZU
8943619920
8943619920
Zexel num
Bosch num
Firm num
Name
101432-0990
9 400 614 115
8943619920 ISUZU
INJECTION-PUMP ASSEMBLY
C240 * K
C240 * K
Calibration Data:
Adjustment conditions
Test oil
1404 Test oil ISO4113 or {SAEJ967d}
1404 Test oil ISO4113 or {SAEJ967d}
Test oil temperature
degC
40
40
45
Nozzle and nozzle holder
105780-8140
Bosch type code
EF8511/9A
Nozzle
105780-0000
Bosch type code
DN12SD12T
Nozzle holder
105780-2080
Bosch type code
EF8511/9
Opening pressure
MPa
17.2
Opening pressure
kgf/cm2
175
Injection pipe
Outer diameter - inner diameter - length (mm) mm 6-2-600
Outer diameter - inner diameter - length (mm) mm 6-2-600
Tester oil delivery pressure
kPa
157
157
157
Tester oil delivery pressure
kgf/cm2
1.6
1.6
1.6
Direction of rotation (viewed from drive side)
Left L
Left L
Injection timing adjustment
Direction of rotation (viewed from drive side)
Left L
Left L
Injection order
1-3-4-2
Pre-stroke
mm
2.25
2.2
2.3
Beginning of injection position
Drive side NO.1
Drive side NO.1
Difference between angles 1
Cal 1-3 deg. 90 89.5 90.5
Cal 1-3 deg. 90 89.5 90.5
Difference between angles 2
Cal 1-4 deg. 180 179.5 180.5
Cal 1-4 deg. 180 179.5 180.5
Difference between angles 3
Cyl.1-2 deg. 270 269.5 270.5
Cyl.1-2 deg. 270 269.5 270.5
Injection quantity adjustment
Adjusting point
A
Rack position
12.6
Pump speed
r/min
750
750
750
Average injection quantity
mm3/st.
41.3
39.7
42.9
Max. variation between cylinders
%
0
-4
4
Fixing the lever
*
Injection quantity adjustment_02
Adjusting point
B
Rack position
12
Pump speed
r/min
1450
1450
1450
Average injection quantity
mm3/st.
43
42
44
Max. variation between cylinders
%
0
-2.5
2.5
Basic
*
Fixing the lever
*
Injection quantity adjustment_03
Adjusting point
-
Rack position
7.6+-0.5
Pump speed
r/min
350
350
350
Average injection quantity
mm3/st.
8
6.9
9.1
Max. variation between cylinders
%
0
-14
14
Fixing the rack
*
Remarks
Adjust only variation between cylinders; adjust governor according to governor specifications.
Adjust only variation between cylinders; adjust governor according to governor specifications.
Test data Ex:
Governor adjustment
N:Pump speed
R:Rack position (mm)
(1)Target notch: K
(2)RACK CAP: R1
----------
K=13 R1=(17.5)mm
----------
----------
K=13 R1=(17.5)mm
----------
Speed control lever angle
F:Full speed
I:Idle
S:Stop
----------
----------
a=20deg+-5deg b=30deg+-5deg c=32deg+-3deg
----------
----------
a=20deg+-5deg b=30deg+-5deg c=32deg+-3deg
Stop lever angle
N:Pump normal
S:Stop the pump.
----------
----------
a=19deg+-5deg b=53deg+-5deg
----------
----------
a=19deg+-5deg b=53deg+-5deg
Timing setting
(1)Pump vertical direction
(2)Gear mark Z for the No. 4 cylinder's beginning of injection
(3)B.T.D.C.: aa
(4)-
----------
aa=18deg
----------
a=(60deg)
----------
aa=18deg
----------
a=(60deg)
Information:
Piston Group.
When handling the piston assembly, be aware that the piston pin plug which fits on the end of the piston pin, is only used to prevent the piston pin from scuffing the cylinders. It does not retain the pin in the assembly, once the piston assembly is removed from the cylinder, the pin is free to fall out of the assembly at any time.
(1) Crater. The piston is a symmetrical piston with an "on center" crater. Thoroughly lubricate piston group 360 degrees in zone (A) with
Have questions with 101432-0990?
Group cross 101432-0990 ZEXEL
Isuzu
101432-0990
9 400 614 115
8943619920
INJECTION-PUMP ASSEMBLY
C240
C240