101431-9870 ZEXEL INJECTION-PUMP ASSEMBLY Calibration Data 1014319870 1679090118

Information Cross number Calibration Data Calibration Data Ex

Information injection-pump assembly

ZEXEL 101431-9870 1014319870

NISSAN-DIESEL 1679090118 1679090118

Price: query

Buy now
Add to cart Go to cart

Rating:

Buy INJECTION-PUMP ASSEMBLY 101431-9870 zexel genuine, new aftermarket engine parts with delivery

Service parts 101431-9870 INJECTION-PUMP ASSEMBLY:

1. _

2. FUEL INJECTION PUMP 101043-8290

3. GOVERNOR 105410-3160

4. SUPPLY PUMP 105220-4630

5. AUTOM. ADVANCE MECHANIS 105622-0240

6. COUPLING PLATE

7. COUPLING PLATE

8. _

9. _

10. NOZZLE AND HOLDER ASSY 105141-1800

11. Nozzle and Holder 16600-90019

12. Open Pre:MPa(Kqf/cm2) 9.8{100}

13. NOZZLE-HOLDER 105071-1240

14. NOZZLE

105000-1010

15. NOZZLE SET

Include in #1:

101431-9870 as INJECTION-PUMP ASSEMBLY

103664-1161 as _

Cross reference number

ZEXEL 101431-9870 1014319870

NISSAN-DIESEL 1679090118 1679090118

Zexel num

Bosch num

Firm num

Name

101431-9870

1679090118 NISSAN-DIESEL

INJECTION-PUMP ASSEMBLY
SD22 * K

Calibration Data:

Adjustment conditions

Test oil
1404 Test oil ISO4113 or {SAEJ967d}

Test oil temperature degC 40 40 45

Nozzle and nozzle holder 105780-8140

Bosch type code EF8511/9A

Nozzle 105780-0000

Bosch type code DN12SD12T

Nozzle holder 105780-2080

Bosch type code EF8511/9

Opening pressure MPa 17.2

Opening pressure kgf/cm2 175

Injection pipe
Outer diameter - inner diameter - length (mm) mm 6-2-600

Tester oil delivery pressure kPa 157 157 157

Tester oil delivery pressure kgf/cm2 1.6 1.6 1.6

Direction of rotation (viewed from drive side)
Right R

Injection timing adjustment

Direction of rotation (viewed from drive side)
Right R

Injection order 1-3-4-2

Pre-stroke mm 2.3 2.25 2.35

Beginning of injection position
Drive side NO.1

Difference between angles 1
Cal 1-3 deg. 90 89.5 90.5

Difference between angles 2
Cal 1-4 deg. 180 179.5 180.5

Difference between angles 3
Cyl.1-2 deg. 270 269.5 270.5

Injection quantity adjustment

Adjusting point A

Rack position 14.3

Pump speed r/min 1000 1000 1000

Average injection quantity mm3/st. 37 35.5 38.5

Max. variation between cylinders % 0 -4 4

Fixing the lever *

Injection quantity adjustment_02

Adjusting point B

Rack position 14.3

Pump speed r/min 1250 1250 1250

Average injection quantity mm3/st. 38.4 37.4 39.4

Max. variation between cylinders % 0 -2.5 2.5

Basic *

Fixing the lever *

Injection quantity adjustment_03

Adjusting point C

Rack position 10.8

Pump speed r/min 300 300 300

Average injection quantity mm3/st. 7.5 6.4 8.6

Max. variation between cylinders % 0 -15 15

Fixing the rack *

Timer adjustment

Pump speed r/min 500

Advance angle deg. 0.5

Timer adjustment_02

Pump speed r/min 550

Advance angle deg. 0.7

Timer adjustment_03

Pump speed r/min 700

Advance angle deg. 1 0.5 1.5

Timer adjustment_04

Pump speed r/min 900

Advance angle deg. 2 1.5 2.5

Timer adjustment_05

Pump speed r/min 1100

Advance angle deg. 3 2.5 3.5

Timer adjustment_06

Pump speed r/min 1300

Advance angle deg. 4 3.5 4.5

Timer adjustment_07

Pump speed r/min -

Advance angle deg. 5 5 5

Remarks
Measure the actual speed, stop

Test data Ex:

Governor adjustment

N:Pump speed R:Rack position (mm) (1)Target notch: K
----------
K=10
----------

Speed control lever angle

F:Full speed I:Idle S:Stop
----------

----------
a=14deg+-5deg b=23deg+-5deg c=32deg+-3deg

Stop lever angle

N:Pump normal S:Stop the pump.
----------

----------
a=(19deg) b=(34deg)

Information:

1. Remove fuel line (1) from the fuel transfer pump.2. Put caps in the fuel line openings to prevent fuel system contamination.3. Remove bolts (2), and remove fuel transfer pump (3). Check the condition of the O-ring seal on the fuel transfer pump. If necessary, make a replacement. The following steps are for installation of the fuel transfer pump.4. Be sure the O-ring seal is in position on the fuel transfer pump. Put clean engine oil on the O-ring seal.5. Put fuel transfer pump (3) in position, and install the bolts that hold it in place.6. Remove the caps from the fuel line openings, and install fuel line (1).Disassemble Fuel Transfer Pump
Start By:a. remove fuel transfer pump 1. Remove seal (1) from the fuel transfer pump.
Cover (2) is under spring tension. Remove the bolts that hold cover (2) slowly to prevent injury.
2. Remove bolts (3) and cover (2) from the housing. 3. Remove seals (4) and valve (5) from cover (2). 4. Remove spring (6) from the piston.
Mark the orientation of valve (8) as to its location in the housing.
5. Remove washer (7), valve (8) and the seal from the housing. 6. Remove piston (9) and sleeve (10) from the housing. 7. Remove seal (11) from sleeve (12). 8. Remove guide and tappet assembly (13) from the housing. 9. Remove seal (14) from guide (15).
If tappet (17) or the guide are damaged or worn, they must be replaced as a unit.
10. Remove ring (16) from tappet (17) and the tappet from guide (15). 11. Remove the bolts and cover (18) from the housing. 12. Remove seal (19) from cover (18). 13. Remove valve (20) from the housing if necessary.Assemble Fuel Transfer Pump
1. Install valve (20) in housing as shown. 2. Put clean fuel on seal (19), and install it on cover (18).3. Install cover (18) on the housing.
The tappet and guide must be serviced as a unit.
4. Install tappet (17) in guide (15). Install ring (16) on tappet (17) to hold the tappet in the guide. 5. Put clean fuel on seal (14), and install it on guide and tappet assembly (13).6. Install guide and tappet assembly (13) in the housing as shown. 7. Put clean fuel on seal (11), and install it on sleeve (12).8. Install sleeve (12) in the housing. 9. Install piston (9) in the housing. 10. Install seal, valve (8) and washer (7) in the housing as shown. Be sure valve (8) is the correct position in the housing. 11. Install spring (6) in the piston. 12. Install valve (5) in cover (2) as shown.13. Put clean fuel on seals (4), and put them in position on cover (2).14. Install cover (2) on the housing. 15. Put seal (1) in position on the fuel transfer pump.16. Install the fuel transfer pump on the fuel injection pump housing.End By:a. install fuel transfer pump