101405-9311 ZEXEL 9 400 613 199 BOSCH INJECTION-PUMP ASSEMBLY 9400613199 1014059311 12991651101

Information Cross number Calibration Data Calibration Data Ex

Information injection-pump assembly

BOSCH 9 400 613 199 9400613199

ZEXEL 101405-9311 1014059311

YANMAR 12991651101 12991651101

Price: query

Buy now
Add to cart Go to cart

Rating:

Buy INJECTION-PUMP ASSEMBLY 101405-9311 zexel genuine, new aftermarket engine parts with delivery

Service parts 101405-9311 INJECTION-PUMP ASSEMBLY:

1. _

2. FUEL INJECTION PUMP 101041-8770

3. GOVERNOR 105419-2153

4. SUPPLY PUMP 105220-7170

5. AUTOM. ADVANCE MECHANIS

6. COUPLING PLATE

7. COUPLING PLATE

8. _

9. _

10. NOZZLE AND HOLDER ASSY

11. Nozzle and Holder

12. Open Pre:MPa(Kqf/cm2)

13. NOZZLE-HOLDER

14. NOZZLE

15. NOZZLE SET

Include in #1:

101405-9311 as INJECTION-PUMP ASSEMBLY

106681-4252 as _

106681-4253

Cross reference number

BOSCH 9 400 613 199 9400613199

ZEXEL 101405-9311 1014059311

YANMAR 12991651101 12991651101

Zexel num

Bosch num

Firm num

Name

101405-9311

9 400 613 199

12991651101 YANMAR

INJECTION-PUMP ASSEMBLY
4TNE94 K 14BC INJECTION PUMP ASSY PE4A,5A, PE

Calibration Data:

Adjustment conditions

Test oil
1404 Test oil ISO4113 or {SAEJ967d}

Test oil temperature degC 40 40 45

Nozzle and nozzle holder 105780-8140

Bosch type code EF8511/9A

Nozzle 105780-0000

Bosch type code DN12SD12T

Nozzle holder 105780-2080

Bosch type code EF8511/9

Opening pressure MPa 17.2

Opening pressure kgf/cm2 175

Injection pipe
Outer diameter - inner diameter - length (mm) mm 6-2-600

Overflow valve 131424-1520

Overflow valve opening pressure kPa 157 123 191

Overflow valve opening pressure kgf/cm2 1.6 1.25 1.95

Tester oil delivery pressure kPa 157 157 157

Tester oil delivery pressure kgf/cm2 1.6 1.6 1.6

Direction of rotation (viewed from drive side)
Right R

Injection timing adjustment

Direction of rotation (viewed from drive side)
Right R

Injection order 1-3-4-2

Pre-stroke mm 3.6 3.55 3.65

Beginning of injection position
Drive side NO.1

Difference between angles 1
Cal 1-3 deg. 90 89.5 90.5

Difference between angles 2
Cal 1-4 deg. 180 179.5 180.5

Difference between angles 3
Cyl.1-2 deg. 270 269.5 270.5

Injection quantity adjustment

Adjusting point A

Rack position 8.8

Pump speed r/min 800 800 800

Average injection quantity mm3/st. 44.7 43.7 45.7

Max. variation between cylinders % 0 -2.5 2.5

Basic *

Fixing the lever *

Injection quantity adjustment_02

Adjusting point C

Rack position 6.5+-0.5

Pump speed r/min 450 450 450

Average injection quantity mm3/st. 13 12 14

Max. variation between cylinders % 0 -15 15

Fixing the rack *

Injection quantity adjustment_03

Adjusting point D

Rack position 9.1++

Pump speed r/min 100 100 100

Average injection quantity mm3/st. 65 60 70

Fixing the lever *

Rack limit *

Test data Ex:

Governor adjustment

N:Pump speed R:Rack position (mm) (1)Target notch: K (2)Tolerance for racks not indicated: +-0.05mm. (3)RACK LIMIT (4)Set idle sub-spring (5)Main spring setting (6)Rack difference between N = N1 and N = N2
----------
K=11 N1=1100r/min N2=800r/min
----------

Speed control lever angle

F:Full speed I:Idle (1)Stopper bolt setting
----------

----------
a=2deg+-5deg b=21deg+-5deg

Stop lever angle

N:Pump normal S:Stop the pump. (1)Normal
----------

----------
a=10deg+-5deg b=53deg+-5deg

Timing setting

(1)Pump vertical direction (2)Position of camshaft's key groove at No 1 cylinder's beginning of injection (3)- (4)-
----------

----------
a=(60deg)

Information:

Table 1
Revision Summary of Changes
01 Title updated. Effectivity and reference added. Changes were made in problem and solution section. Introduction
The problem that is identified below does not have a known permanent solution. Until a permanent solution is known, use the solution that is identified below.Problem
Illustration 1 g06583948
Clogged diesel particulate filter
Reports have been received that the Diesel Particulate Filter (DPF) may clog at less than 300 hours on the machines listed above. The insulation from the Diesel Oxidation Catalyst (DOC) causes clogging of the DPF.These additional related problems may occur:
Diagnostic code 523602-0"Aftertreatment Regeneration Frequency" may occur
Erratic soot levels
Fuel dilution of the oil or poor oil quality at low machine hoursSolution
Do not operate or work on this product unless you have read and understood the instruction and warnings in the relevant Operation and Maintenance Manuals and relevant service literature. Failure to follow the instructions or heed the warnings could result in injury or death. Proper care is your responsibility.
In the event of failure, follow the troubleshooting procedure below:Troubleshooting Procedure
Check the fuel/water separator for water.Note: Water in fuel can cause excessive ash buildup in the DPF.
Check the air filter and replace the air filter if necessary.
Check the engine oil level and look for fuel dilution of engine oil. Replace the engine oil and filter if fuel dilution has occurred.Note: Frequent regeneration may cause fuel dilution of engine oil due to the fuel dosing required for regeneration. A failed injector could also cause fuel dilution of engine oil.
Check the coolant level.
Troubleshoot active diagnostic codes. Refer to Troubleshooting, UENR3390 on how to troubleshoot excessive DPF regeneration.
Complete a parked DPF regeneration to remove soot.
Inspect the differential pressure sensor tubes for damage.
Inspect the differential pressure sensor tubes and sensors for debris.
Bring the engine up to operating temperature and complete a fuel injector cut-out test to test for failed injectors.If the problem exists even after performing the troubleshooting procedure, create a Global Dealer Solution Network (GDSN) Product Health Service Request (SR) with Workgroup / Subsystem of “Base Machine”. Attach any pertinent photos and detailed failure information for the product group. Mention the CPI number 471218 in the CPI field (and /or) the Technical Information Bulletin (TIB) media number (M0121625) in the description prior to submitting to Caterpillar.Additional troubleshooting/documentation may include:
A photo of the DPF and DOC for identification information
An inspection of the face of the DPF for fibrous material
An inspection of engine oil sample
An inspection of the fuel sample if needed based on diagnostic codes