101402-9820 ZEXEL 9 400 614 029 BOSCH INJECTION-PUMP ASSEMBLY 9400614029 1014029820 3426103040


 

Information injection-pump assembly

BOSCH 9 400 614 029 9400614029
ZEXEL 101402-9820 1014029820
MITSUBISHI-HEAV 3426103040 3426103040
101402-9820 INJECTION-PUMP ASSEMBLY
Rating:
81
Buy INJECTION-PUMP ASSEMBLY 101402-9820 zexel genuine, new aftermarket engine parts with delivery

Include in #1:

Cross reference number

Zexel num
Bosch num
Firm num
Name
101402-9820 
9 400 614 029 
3426103040  MITSUBISHI-HEAV
INJECTION-PUMP ASSEMBLY
S4K-T K




Information:

1. Drain the coolant and oil from the engine.2. Remove bolt (1) and retainer (2) that hold the oil lines in the BrakeSaver control valve. 3. Disconnect oil lines (3) and (4) from the oil cooler. Remove oil lines (3) and (4) from the BrakeSaver control valve.4. Fasten a hoist to the oil cooler. 5. Remove two bolts (8) to disconnect elbow (10) from front bonnet (9). Remove two bolts (7) to disconnect front bonnet (9) from the water pump.6. Remove four bolts (5) to disconnect the rear bonnet from the cylinder block. Disconnect bracket (12).7. Remove oil cooler (11), front bonnet (9) and rear bonnet (6) from the engine as a unit. The weight is approximately 54 kg (120 lb.).8. Make a separation of front bonnet (9) and rear bonnet (6) from oil cooler (11). 9. Clean oil cooler core tubes (13) with a 3.81 mm (.150 in.) diameter rod.10. Inspect all O-ring seals and gaskets for damage, and make replacements if needed. Put clean engine oil on the O-ring seals.11. Install rear bonnet (6) and front bonnet (9) on oil cooler (11).12. Fasten a hoist, and put the oil cooler and bonnets as a unit in place on the engine. Connect bracket (12) but do not tighten the bolts at this time.13. Install the gasket and four bolts (5) that hold rear bonnet (6) to the engine block. Do not tighten the bolts at this time.14. Install the gasket and two bolts (7) that hold front bonnet (9) to the water pump. Do not tighten the bolts at this time.15. Install the gasket and bolts (8) that hold elbow (10) to the front bonnet. Tighten all the bolts.16. Make sure the O-ring seals are in place on the oil lines, and install oil lines (3) and (4).17. Install retainer (2) to hold the oil lines in the BrakeSaver control valve. If the bottom plug in the oil pan was removed, put the split (seam) of the gasket for the plug against the oil pan. If either plug on the side of the oil pan was removed, put 5P3413 Thread Sealant With Teflon on the threads, and tighten the plug to a torque of 80 11 N m (60 8 lb.ft.).18. Fill the engine with coolant and oil. See the Maintenance Manual.

Have questions with 101402-9820?





Group cross 101402-9820 ZEXEL

 
 
INJECTION-PUMP ASSEMBLY
4TNE94
 
 
INJECTION-PUMP ASSEMBLY

Yanmar 

 
12991651010 
INJECTION-PUMP ASSEMBLY
4TNE94
9 400 613 435 
12991651011 
INJECTION-PUMP ASSEMBLY
4TNE94

Mitsubishi-Heav 

9 400 614 028 
3426104050 
INJECTION-PUMP ASSEMBLY
S4K
101402-9820  
9 400 614 029 
3426103040 
INJECTION-PUMP ASSEMBLY
S4K-T
9 400 614 030 
3426103090 
INJECTION-PUMP ASSEMBLY
S4K-T
9 400 611 314 
3426113030 
INJECTION-PUMP ASSEMBLY
S4K
9 400 611 579 
3426112050 
INJECTION-PUMP ASSEMBLY
S4K-T
 
 
INJECTION-PUMP ASSEMBLY
4TNE98
 
 
INJECTION-PUMP ASSEMBLY

Yanmar 

9 400 614 031 
12992051000 
INJECTION-PUMP ASSEMBLY
4TNE98

Dpico 

F 019 Z10 941 
 
INJECTION-PUMP ASSEMBLY
4D31T

Mitsubishi-Heav 

9 400 614 032 
3426104060 
INJECTION-PUMP ASSEMBLY
S4K-T
9 400 611 382 
3426113060 
INJECTION-PUMP ASSEMBLY
S4K
Back to top