101402-2041 ZEXEL 9 400 613 850 BOSCH INJECTION-PUMP ASSEMBLY 9400613850 1014022041 220202711a

Information Cross number Calibration Data Calibration Data Ex

Information injection-pump assembly

BOSCH 9 400 613 850 9400613850

ZEXEL 101402-2041 1014022041

HINO 220202711A 220202711a

Price: query

Buy now
Add to cart Go to cart

Rating:

Buy INJECTION-PUMP ASSEMBLY 101402-2041 zexel genuine, new aftermarket engine parts with delivery

Service parts 101402-2041 INJECTION-PUMP ASSEMBLY:

1. _

2. FUEL INJECTION PUMP 101040-9300

3. GOVERNOR 105400-4000

4. SUPPLY PUMP 105220-5300

5. AUTOM. ADVANCE MECHANIS

6. COUPLING PLATE

7. COUPLING PLATE 156636-4821

8. _

9. _

10. NOZZLE AND HOLDER ASSY 105110-4320

11. Nozzle and Holder

12. Open Pre:MPa(Kqf/cm2) 21.6{220}

13. NOZZLE-HOLDER 105041-5041

14. NOZZLE 105015-6240

15. NOZZLE SET

Include in #1:

101402-2041 as INJECTION-PUMP ASSEMBLY

107691-3194 as _

Cross reference number

BOSCH 9 400 613 850 9400613850

ZEXEL 101402-2041 1014022041

HINO 220202711A 220202711a

Zexel num

Bosch num

Firm num

Name

101402-2041

9 400 613 850

220202711A HINO

INJECTION-PUMP ASSEMBLY
W04CT K 14BC INJECTION PUMP ASSY PE4A,5A, PE

Calibration Data:

Adjustment conditions

Test oil
1404 Test oil ISO4113 or {SAEJ967d}

Test oil temperature degC 40 40 45

Nozzle and nozzle holder 105780-8140

Bosch type code EF8511/9A

Nozzle 105780-0000

Bosch type code DN12SD12T

Nozzle holder 105780-2080

Bosch type code EF8511/9

Opening pressure MPa 17.2

Opening pressure kgf/cm2 175

Injection pipe
Outer diameter - inner diameter - length (mm) mm 6-2-600

Overflow valve 134424-2920

Overflow valve opening pressure kPa 162 147 177

Overflow valve opening pressure kgf/cm2 1.65 1.5 1.8

Tester oil delivery pressure kPa 157 157 157

Tester oil delivery pressure kgf/cm2 1.6 1.6 1.6

Direction of rotation (viewed from drive side)
Right R

Injection timing adjustment

Direction of rotation (viewed from drive side)
Right R

Injection order 1-3-4-2

Pre-stroke mm 3.2 3.17 3.23

Beginning of injection position
Drive side NO.1

Difference between angles 1
Cal 1-3 deg. 90 89.75 90.25

Difference between angles 2
Cal 1-4 deg. 180 179.75 180.25

Difference between angles 3
Cyl.1-2 deg. 270 269.75 270.25

Injection quantity adjustment

Adjusting point A

Rack position 10.4

Pump speed r/min 900 900 900

Average injection quantity mm3/st. 74 72 76

Max. variation between cylinders % 0 -3 3

Basic *

Fixing the lever *

Injection quantity adjustment_02

Adjusting point C

Rack position 7.7+-0.5

Pump speed r/min 600 600 600

Average injection quantity mm3/st. 22.8 21.3 24.3

Max. variation between cylinders % 0 -15 15

Fixing the rack *

Test data Ex:

Governor adjustment

N:Pump speed R:Rack position (mm) (1)Target notch: K (2)Main spring setting (3)Set idle sub-spring
----------
K=14
----------

Speed control lever angle

F:Full speed I:Idle (1)Stopper bolt setting
----------

----------
a=16deg+-5deg b=20deg+-5deg

Stop lever angle

N:Pump normal S:Stop the pump.
----------

----------
a=27deg+-5deg b=53deg+-5deg

Timing setting

(1)Pump vertical direction (2)Position of gear's standard threaded hole at No 1 cylinder's beginning of injection (3)- (4)-
----------

----------
a=(70deg)

Information:

Installation Procedure
Illustration 1 g06124125
Remove plate (1) and discard. Save the hardware and hook assembly (2) for reuse.
Illustration 2 g06124137
(3) 5I-3822 Plate
Weld plate (3) in the location specified in Illustration 2.
Illustration 3 g06124150
Remove two hoses (4).
Illustration 4 g06124157
(5) 467-9635 Hose
(6) 428-8808 Hose Clamp
(7) 418-2057 Hose
(8) 467-9634 Hose
(9) 5P-4924 Elbow
(10) 6V-3250 O-Ring Seal
(11) 424-1209 Tank
Install hose (7) and two hose clamps (6). Slowly tighten the clamps to 6.6 0.2 N m (58 1.8 lb in).
Install one end of hose (5) on the coolant tube and the other on tank (11). Secure the hose using two hose clamps (6). Slowly tighten the clamps to 6.6 0.2 N m (58 1.8 lb in).
Install elbow (9) and O-ring (10) onto tank (11). Tighten the elbow to 28 4 N m (21 3 lb ft).
Install hose (8) as shown using two hose clamps (6). Slowly tighten the clamps to 6.6 0.2 N m (58 1.8 lb in). Ensure the hoses connected to the tank are in parallel as shown in view D-D.
Illustration 5 g06124173
(12) 326-4516 Cable Tie
(13) 454-4235 Plate
Secure the hoses as shown using two cable ties (12) and plate (13).
Illustration 6 g06124183
(14) 511-8273 Sheet As
Install sheet (14) and hook assembly (2) using the saved hardware.
Illustration 7 g06124176
(11) 424-1209 Tank
(15) 467-9640 Plate As
(16) 8T-4136 Bolt
(17) 8T-4121 Hard Washer
(18) 8T-4189 Bolt
(19) 8T-4224 Hard Washer
Install plate assembly (15) using three bolts (16) and three washers (17).
Mount tank (11) onto plate (15) using two bolts (18) and two washers (19).
Install new machine, engine, and after treatment software. The new software is available in the form of a flash file through the Caterpillar Service Information System (SIS). SIS web only displays the latest available flash file.
Illustration 8 g06123932
Update the DES threshold to 525 degrees C using Cat® Electronic Technician (Cat ET). A factory password is required to change the value. A factory password can be obtained after inputting your Corporate Web Security (CWS) identification.