101401-9761 ZEXEL INJECTION-PUMP ASSEMBLY Calibration Data 1014019761

Information Cross number Calibration Data Calibration Data Ex

Information injection-pump assembly

ZEXEL 101401-9761 1014019761

Price: query

Buy now
Add to cart Go to cart

Rating:

Buy INJECTION-PUMP ASSEMBLY 101401-9761 zexel genuine, new aftermarket engine parts with delivery

Service parts 101401-9761 INJECTION-PUMP ASSEMBLY:

1. _

2. FUEL INJECTION PUMP 101041-9330

3. GOVERNOR 105921-9081

4. SUPPLY PUMP 105220-7060

5. AUTOM. ADVANCE MECHANIS 105671-0500

6. COUPLING PLATE

7. COUPLING PLATE

8. _

9. _

10. NOZZLE AND HOLDER ASSY 105118-6170

11. Nozzle and Holder 16600-17D02

12. Open Pre:MPa(Kqf/cm2) 19.6{200}

13. NOZZLE-HOLDER 105048-3691

14. NOZZLE 105017-2010

15. NOZZLE SET

Include in #1:

101401-9761 as INJECTION-PUMP ASSEMBLY

106673-3233 as _

Cross reference number

ZEXEL 101401-9761 1014019761

Zexel num

Bosch num

Firm num

Name

101401-9761

INJECTION-PUMP ASSEMBLY
FD46T 14BD PE4AD PE

Calibration Data:

Adjustment conditions

Test oil
1404 Test oil ISO4113 or {SAEJ967d}

Test oil temperature degC 40 40 45

Nozzle and nozzle holder 105780-8140

Bosch type code EF8511/9A

Nozzle 105780-0000

Bosch type code DN12SD12T

Nozzle holder 105780-2080

Bosch type code EF8511/9

Opening pressure MPa 17.2

Opening pressure kgf/cm2 175

Injection pipe
Outer diameter - inner diameter - length (mm) mm 6-2-600

Overflow valve 134424-4120

Overflow valve opening pressure kPa 255 221 289

Overflow valve opening pressure kgf/cm2 2.6 2.25 2.95

Tester oil delivery pressure kPa 157 157 157

Tester oil delivery pressure kgf/cm2 1.6 1.6 1.6

Direction of rotation (viewed from drive side)
Right R

Injection timing adjustment

Direction of rotation (viewed from drive side)
Right R

Injection order 1-3-4-2

Pre-stroke mm 3.2 3.15 3.25

Rack position
Point A R=A

Beginning of injection position
Drive side NO.1

Difference between angles 1
Cal 1-3 deg. 90 89.5 90.5

Difference between angles 2
Cal 1-4 deg. 180 179.5 180.5

Difference between angles 3
Cyl.1-2 deg. 270 269.5 270.5

Injection quantity adjustment

Adjusting point -

Rack position 14.6

Pump speed r/min 1550 1550 1550

Average injection quantity mm3/st. 108.5 106.9 110.1

Max. variation between cylinders % 0 -3.5 3.5

Basic *

Fixing the rack *

Standard for adjustment of the maximum variation between cylinders *

Injection quantity adjustment_02

Adjusting point H

Rack position 9.7+-0.5

Pump speed r/min 325 325 325

Average injection quantity mm3/st. 13 11.2 14.8

Max. variation between cylinders % 0 -10 10

Fixing the rack *

Standard for adjustment of the maximum variation between cylinders *

Injection quantity adjustment_03

Adjusting point A

Rack position R1(14.6)

Pump speed r/min 1550 1550 1550

Average injection quantity mm3/st. 108.5 107.5 109.5

Basic *

Fixing the lever *

Boost pressure kPa 70.6 70.6

Boost pressure mmHg 530 530

Injection quantity adjustment_04

Adjusting point B

Rack position R1-1.05

Pump speed r/min 900 900 900

Average injection quantity mm3/st. 88 84 92

Fixing the lever *

Boost pressure kPa 70.6 70.6

Boost pressure mmHg 530 530

Injection quantity adjustment_05

Adjusting point C

Rack position R2-0.95

Pump speed r/min 500 500 500

Average injection quantity mm3/st. 58 54 62

Fixing the lever *

Boost pressure kPa 0 0 0

Boost pressure mmHg 0 0 0

Boost compensator adjustment

Pump speed r/min 500 500 500

Rack position R2-0.95

Boost pressure kPa 10.7 9.4 12

Boost pressure mmHg 80 70 90

Boost compensator adjustment_02

Pump speed r/min 500 500 500

Rack position R2[R1-1. 35]

Boost pressure kPa 57.3 57.3 57.3

Boost pressure mmHg 430 430 430

Timer adjustment

Pump speed r/min 1000--

Advance angle deg. 0 0 0

Remarks
Start

Timer adjustment_02

Pump speed r/min 950

Advance angle deg. 0.5

Timer adjustment_03

Pump speed r/min 1550

Advance angle deg. 5.1 4.6 5.6

Timer adjustment_04

Pump speed r/min -

Advance angle deg. 7 6.5 7.5

Remarks
Measure the actual speed, stop

Test data Ex:

Governor adjustment

N:Pump speed R:Rack position (mm) (1)Torque cam stamping: T1 (2)Tolerance for racks not indicated: +-0.05mm. (3)Boost compensator stroke: BCL
----------
T1=L33 BCL=0.95+-0.1mm
----------

Speed control lever angle

F:Full speed I:Idle (1)Use the hole at R = aa (2)Stopper bolt setting
----------
aa=32mm
----------
a=71deg+-5deg b=(38deg)+-3deg

Stop lever angle

N:Pump normal S:Stop the pump. (1)Use the pin at R = aa
----------
aa=15mm
----------
a=29deg+-5deg b=10deg+-5deg

0000001501 POTENTIO METER

(A) : Governor plan view (B): Potentiometer harness terminal (C): Potentiometer connection diagram (D) : Output voltage standard value (S): Voltage P/M: potentiometer (v): output voltage (V) (p): direction of potentiometer rotation 1. Adjustment procedures (1)Apply DCV1 to potentiometer harness terminal (B) to obtain the specified output voltage. (2)Fix the speed lever at the full side. (3)Loosen the bolt (S), and move the potentiometer from left and right. (4)Adjust so that the output voltage at full is within the standard values. (5)Fix bolt (S). (6)Repeatedly move the speed lever from the full side to the idle side. (7)Check that it is within the standard values at full and idle.
----------
V1=5+-0.02V
----------
V1=5+-0.02V Va=(5)V Vb=(3.75)+-0.2V Vc=0.58+-0.3V

Timing setting

(1)Pump vertical direction (2)Position of gear's standard threaded hole at No 1 cylinder's beginning of injection (3)B.T.D.C.: aa (4)-
----------
aa=5deg
----------
a=(50deg)

Information:

Introduction
This Special Instruction is intended for the installation of the 366-9748 Injector Wiring Harness Kit . The 366-9748 Injector Wiring Harness Kit can be used to repair TPI connectors. TPI connectors can be found on HEUI injectors, variable valve actuators, and Cat Brakes.Removal of the Connector From the Wire Harness
Table 1
Required Tools
Tool Part Number Part Description Qty
A 9S-9150 Terminal Crimp Tool As 1
B 9U-6070
or Heat Gun Gp
(110V) 1
9U-6072 Heat Gun Gp (220 V) The following steps will remove the connector for an injector from the wire harness that is under the valve mechanism cover.
Illustration 1 g01035448
(1) Side "A" of the connector (2) Side "B" of the connectorNote: Side "A" or side "1" of the connector is the output signal wire from the ECM. Side"B" or side "2" of the connector is the sensor return.
Identify side "A" of the connector and identify side "B" of the connector.
Mark each wire on the wire harness before the wires are cut. Most connectors will have the label of an "A" and a "B". Some connectors may have a "1" and a "2" that is on the connector. The label with a "1" will be an "A". The label with a "2" will be a "B".
Illustration 2 g01034438
Connector that is cut from the wire harness (3) Wire on side "A" of the connector (4) Wire on side "B" of the connector
Cut wire (3) at a distance of 45 mm (1.8 inch).
Cut wire (4) at a distance of 40 mm (1.6 inch).
Illustration 3 g01034450
(5) Wire from the harness for side "B" on the connector (6) Wire from the harness for side "A" on the connectorNote: The wires on the old connector are cut to length so that the wires on the wire harness to the new connector will match up. The proper length will help in matching the harness wires to the wires on the new connector wires.
Discard the connector.Installation Procedure for the Connector
Use Tool (A) to strip the plastic off wires (5) and (6) at a distance of 5 mm (0.19 inch).
Illustration 4 g01034451
Connecting the connector to the wire harness (5) Wire from the harness for side "B" on the connector (6) Wire from the harness for side "A" on the connector (7) Heat shrink tube (8) Butt splice on wire (4) that is on side "B" of the connector (9) Butt splice on wire (3) that is on side "A" of the connector
Use the heat shrink tubes from 366-9748 Injector Wiring Harness Kit . Slide the heat shrink tubes toward the connector in order to expose the butt splices.
Take wire (5) and slide wire (5) in the butt splice (8).
Take wire (6) and slide wire (6) in the butt splice (9).
Illustration 5 g01035814
Illustration 6 g01034452
(8) Butt splice on wire (4) that is on side "B" of the connector (9) Butt splice on wire (3) that is on side "A" of the connector
Use Tool