101401-1900 ZEXEL 9 400 611 874 BOSCH INJECTION-PUMP ASSEMBLY 9400611874 1014011900 me440013

Information Cross number Calibration Data Calibration Data Ex

Information injection-pump assembly

BOSCH 9 400 611 874 9400611874

ZEXEL 101401-1900 1014011900

MITSUBISHI ME440013 me440013

Price: query

Buy now
Add to cart Go to cart

Rating:

Buy INJECTION-PUMP ASSEMBLY 101401-1900 zexel genuine, new aftermarket engine parts with delivery

Service parts 101401-1900 INJECTION-PUMP ASSEMBLY:

1. _

2. FUEL INJECTION PUMP 101041-9110

3. GOVERNOR 105400-9320

4. SUPPLY PUMP 105220-6361

5. AUTOM. ADVANCE MECHANIS 105676-0940

6. COUPLING PLATE

7. COUPLING PLATE

8. _

9. _

10. NOZZLE AND HOLDER ASSY 105118-5031

11. Nozzle and Holder ME016655

12. Open Pre:MPa(Kqf/cm2) 21.6{220}

13. NOZZLE-HOLDER 105048-3590

14. NOZZLE

105017-1040

15. NOZZLE SET

Include in #1:

101401-1900 as INJECTION-PUMP ASSEMBLY

108622-3461 as _

Cross reference number

BOSCH 9 400 611 874 9400611874

ZEXEL 101401-1900 1014011900

MITSUBISHI ME440013 me440013

Zexel num

Bosch num

Firm num

Name

101401-1900

9 400 611 874

ME440013 MITSUBISHI

INJECTION-PUMP ASSEMBLY
4D34T K 14BC INJECTION PUMP ASSY PE4A,5A, PE

Calibration Data:

Adjustment conditions

Test oil
1404 Test oil ISO4113 or {SAEJ967d}

Test oil temperature degC 40 40 45

Nozzle and nozzle holder 105780-8140

Bosch type code EF8511/9A

Nozzle 105780-0000

Bosch type code DN12SD12T

Nozzle holder 105780-2080

Bosch type code EF8511/9

Opening pressure MPa 17.2

Opening pressure kgf/cm2 175

Injection pipe
Outer diameter - inner diameter - length (mm) mm 6-2-600

Overflow valve 131424-4620

Overflow valve opening pressure kPa 255 221 289

Overflow valve opening pressure kgf/cm2 2.6 2.25 2.95

Tester oil delivery pressure kPa 157 157 157

Tester oil delivery pressure kgf/cm2 1.6 1.6 1.6

Direction of rotation (viewed from drive side)
Right R

Injection timing adjustment

Direction of rotation (viewed from drive side)
Right R

Injection order 1-3-4-2

Pre-stroke mm 3.5 3.45 3.55

Beginning of injection position
Drive side NO.1

Difference between angles 1
Cal 1-3 deg. 90 89.5 90.5

Difference between angles 2
Cal 1-4 deg. 180 179.5 180.5

Difference between angles 3
Cyl.1-2 deg. 270 269.5 270.5

Injection quantity adjustment

Adjusting point A

Rack position 10.7

Pump speed r/min 950 950 950

Average injection quantity mm3/st. 77.5 76.5 78.5

Max. variation between cylinders % 0 -2.5 2.5

Basic *

Fixing the lever *

Injection quantity adjustment_02

Adjusting point -

Rack position 8.3+-0.5

Pump speed r/min 445 445 445

Average injection quantity mm3/st. 8 6.7 9.3

Max. variation between cylinders % 0 -14 14

Fixing the rack *

Remarks
Adjust only variation between cylinders; adjust governor according to governor specifications.

Injection quantity adjustment_03

Adjusting point C

Rack position 11.2++

Pump speed r/min 100 100 100

Average injection quantity mm3/st. 45 45 50

Fixing the lever *

Rack limit *

Timer adjustment

Pump speed r/min 0

Advance angle deg. 2.5 2 3

Timer adjustment_02

Pump speed r/min 350

Advance angle deg. 2.5 2 3

Remarks
Start

Timer adjustment_03

Pump speed r/min 500

Advance angle deg. 0 0 0

Remarks
Finish

Test data Ex:

Governor adjustment

N:Pump speed R:Rack position (mm) (1)Notch fixed: K (2)Tolerance for racks not indicated: +-0.05mm. (3)RACK LIMIT (4)Set idle sub-spring (5)Main spring setting (6)Rack difference between N = N1 and N = N2
----------
K=6 N1=950r/min N2=600r/min
----------

Speed control lever angle

F:Full speed I:Idle (1)Stopper bolt setting
----------

----------
a=(1deg)+-5deg b=(14deg)+-5deg

Stop lever angle

N:Pump normal S:Stop the pump. (1)No return spring (2)When the solenoid is operating, the rack position must not exceed bb (at voltage ff) at speed = aa.
----------
aa=0r/min bb=7.6mm ff=24V
----------
a=27deg+-5deg b=53deg+-5deg

Timing setting

(1)Pump vertical direction (2)Position of gear mark '3' at No 1 cylinder's beginning of injection (3)B.T.D.C.: aa (4)-
----------
aa=12deg
----------
a=(130deg)

Information:

(1) Outer spring: Length under test force ... 27.4 mm (1.08 in.)Test force ... 180 9 N (40 2 lb.)Free length after test ... 45.2 mm (1.78 in.)(Damper coils of spring go toward cylinder head.)(2) Inner spring: Length under test force ... 23.88 mm (.940 in.)Test force ... 69 9 N (15.4 2 lb.)Free length after test ... 39.6 mm (1.56 in.)(Damper coils of spring go toward cylinder head.)(3) Valve guides: Inside diameter ... 9.507 to 9.543 mm (.3743 to .3757 in.)Outside diameter ... 15.921 to 15.933 mm (.6268 to .6273 in.)Parent bore diameter in cylinder head for valve guide ... 15.867 to 15.893 mm (.6247 to .6257 in.)Interference fit of guide in cylinder head ... 0.028 to 0.066 mm (.0011 to .0026 in.)Overall length of guide: Intake ... 57.94 mm (2.281 in.)Exhaust ... 61.11 mm (2.406 in.)Projection of guide above valve spring recess ... 15.09 mm (.594 in.)(4) Intake valve: Valve stem diameter ... 9.42 to 9.45 mm (.371 to .372 in.)Clearance of valve in guide ... 0.058 to 0.119 mm (.0023 to .0047 in.)Maximum permissible clearance of valve in guide ... 0.13 mm (.005 in.)Valve head diameter ... 44.09 to 44.35 mm (1.736 to 1.746 in.) Grinding angles: Valve face angle ... 45°Valve seat angle ... 45°Valve head depth below cylinder head face: Minimum ... 1.02 mm (.040 in.)Maximum ... 1.27 mm (.050 in.)Service wear limit ... 1.52 mm (.060 in.)Overall length of valve ... 122.71 to 123.11 mm (4.831 to 4.847 in.)(5) Exhaust valve: Valve stem diameter ... 9.42 to 9.45 mm (.371 to .372 in.)Clearance of valve in guide ... 0.058 to 0.119 mm (.0023 to .0047 in.)Maximum permissible clearance of valve in guide (all models) ... 0.15 mm (.006 in.)Valve head diameter ... 37.26 to 37.52 mm (1.467 to 1.477 in.)Grinding angles: Valve face angle ... 45°Valve seat angle ... 45°Valve head depth below cylinder head face: Minimum ... 1.02 mm (.040 in.)Maximum ... 1.27 mm (.050 in.)Service wear limit ... 1.52 mm (.060 in.)Overall length of valve ... 123.11 to 123.52 mm (4.847 to 4.863 in.)(6) Maximum permissible depth of bore to grind the flare of the valve seat ... 2.69 to 2.79 mm (.106 to .110 in.)(7) Angle to grind flare of valve seat ... 33° (8) Use the dimensions that follow to machine the recess into the cylinder head for valve seat inserts not already installed in the head. Intake: A ... 7.19 to 7.32 mm (.283 to .288 in.)B ... 51.219 to 51.245 mm (2.0165 to 2.0175 in.)C (Radius) ... 0.38 mm (.015 in.)Exhaust: A ... 9.53 to 9.65 mm (.375 to .380 in.)B ... 42.62 to 42.65 mm (1.678 to 1.679 in.)C (Radius) ... 0.38 mm (.015 in.)