Buy 146400-1420 ZEXEL 9 461 610 165 BOSCH HYDRAULIC HEAD 9461610165 1464001420 16760r8100


 

Information hydraulic head

BOSCH 9 461 610 165 9461610165
ZEXEL 146400-1420 1464001420
NISSAN 16760R8100 16760r8100
146400-1420 HYDRAULIC HEAD
Rating:
16
Buy HYDRAULIC HEAD 146400-1420 zexel genuine, new aftermarket engine parts with delivery

Compare Prices: .

As an associate, we earn commssions on qualifying purchases through the links below
£329.01
 

04 Feb 2018

Bosch: Bosch
Bosch 9461610165 Hydraulic Head

Cross reference number

Zexel num
Bosch num
Firm num
Name
146400-1420 
9 461 610 165 
16760R8100  NISSAN
HYDRAULIC HEAD
C 11FV DISTRIBUTOR HEAD parts(VE) Others
146400-1420 
9 461 610 165 
16760R8100  NISSAN-DIESEL
HYDRAULIC HEAD
C 11FV DISTRIBUTOR HEAD parts(VE) Others




Information:


Governor Linkage Adjustment
(1) Rod. (2) Nut. (3) Control lever. (4) Lever. (5) Pin. (6) High idle stop. (7) Locknut. (8) Low idle stop. (9) Locknut. (10) Decelerator treadle. (11) Floor plate. (12) Accelerator treadle. (13) Lever. (14) Rod. (15) Locknut. (16) Lever. (17) Locknut. (A) 9.7 1.5 mm (.38 .06 in). (B) 4.8 1.5 mm (.19 .06 in). (C) 38.1 1.5 mm (1.50 .06 in). (D) 60.5 3.0 mm (2.38 .12 in).Governor Linkage Adjustment
DO NOT USE control lever (3), or decelerator treadle (10) to shut OFF the engine.To shut engine OFF, pull up on accelerator treadle (12).1. Tighten nut (2) just enough so position of control lever (3) is not affected by the operation of the accelerator treadle (12) and decelerator treadle (10).2. With the parking brake ON and engine stopped, BE SURE disconnect switch is OFF.3. Remove pin (5).4. Loosen LOW IDLE stop (8) and HIGH IDLE stop (6) so they do not touch lever (13).5. Move control lever (3) to LOW IDLE position.6. Turn LOW IDLE stop (8) until it touches lever (13) and tighten locknut (9).7. Adjust length of rod (14) so distance from top of lever (16) to bottom of floor plate (11) is (C) 38.1 1.5 mm (1.50 .06 in) as shown.8. Loosen locknut (15) and adjust length of rod so top of decelerator treadle (10) is (B) 4.8 mm (.19 in) above floor plate (11) as shown. If machine is equipped with a thick floor insulation pad, (used with enclosed cab), adjust decelerator treadle (10) so top of treadle is (A) 9.7 1.5 mm (.38 .06 in) above top of floor plate and tighten locknut (15).9. Move control lever (3) to HIGH IDLE position.10. Turn HIGH IDLE stop (6) until it touches lever (13) and tighten locknut (7).11. Loosen locknut (17) and adjust accelerator treadle (12) so that distance from bottom of plate on treadle to top of floor plate (11) is (D) 60.5 3.0 mm (2.38 .12 in) as shown.12. Move lever (4) to HIGH IDLE position and adjust length of rod (1) so pin (5) can be installed.13. Install pin (5).
DO NOT adjust the linkage so the treadle can be used to shut off the engine. If the operator is in a standing position and places a foot on the treadle, the engine could be unexpectedly shut off, creating a situation where the machine can be difficult to control.
814B, 815B, 816B, 966D
1. Set governor shaft to the off position (approximately 35° right of twelve o'clock) and attach lever (1).2. Adjust cable assembly (2) to within 3 mm (.12 in) of the end of travel and tighten bulkhead (3) nuts to ... 100 15

Have questions with 146400-1420?





Group cross 146400-1420 ZEXEL

Nissan 

146400-1420  
9 461 610 165 
16760R8100 
HYDRAULIC HEAD

Nissan-Diesel 

146400-1420  
9 461 610 165 
16760R8100 
HYDRAULIC HEAD
Back to top