105866-7012 ZEXEL F 019 Z2E 488 BOSCH HYDRAULIC GOVERNOR f019z2e488 1058667012


 

Information hydraulic governor

BOSCH F 019 Z2E 488 f019z2e488
ZEXEL 105866-7012 1058667012
105866-7012 HYDRAULIC GOVERNOR
Rating:
64
Buy HYDRAULIC GOVERNOR 105866-7012 zexel genuine, new aftermarket engine parts with delivery

Components :

0. INJECTION-PUMP ASSEMBLY 105866-7012
1. _
2. FUEL INJECTION PUMP
3. NUMBER PLATE
4. _
5. CAPSULE
6. ADJUSTING DEVICE
7. NOZZLE AND HOLDER ASSY
8. Nozzle and Holder
9. Open Pre:MPa(Kqf/cm2)
10. NOZZLE-HOLDER
11. NOZZLE

Scheme ###:

1. [1] 158502-0420 BASE
2. [1] 029811-8000 BEARING PLATE
3. [1] 158528-0900 PACKING RING
7. [1] 158131-0100 GEAR SHAFT
10. [1] 158028-0000 O-RING
11. [1] 158507-1220 DIAPHRAGM HOUSING
13. [1] 158621-0500 SLEEVE
18. [1] 158699-0621 COMPENSATOR ASSY
18/1. [1] 158610-1101 POWER PISTON
18/3. [1] 158654-0800 COILED SPRING
18/4. [1] 158614-0700 STOP PIN
18/5. [1] 158612-0500 PLAIN WASHER
18/6. [1] 158654-0900 COILED SPRING
18/7. [1] 016110-1220 LOCKING WASHER
18/8. [1] 158612-0401 BUSHING
18/9. [2] 016550-2310 O-RING
18/10. [1] 158615-0500 PUMP PLUNGER
18/11. [1] 025620-1410 SPRING PIN
35. [3] 029330-6070 GASKET
36. [3] 010206-2520 HEX-SOCKET-HEAD CAP SCREW
50. [1] 158600-0720 FLYWEIGHT ASSEMBLY
51. [1] 158106-0100 PLAIN WASHER
52. [1] 029811-0000 BEARING PLATE
53. [1] 158620-1420 PILOT VALVE
60. [2] 158220-0000 GUIDE LEVER
61. [2] 158736-0200 BEARING PIN
62. [4] 025520-1510 SPLIT PIN
70. [1] 158730-0220 TERMINAL ARM
70/1. [1] 158230-0020 TERMINAL ARM
70/2. [1] 158315-0200 TERMINAL SHAFT
70/3. [1] 158315-0200 TERMINAL SHAFT
70/4. [2] 158736-0100 TAPER PIN
70/5. [2] 011006-0620 SET OF NUTS
70/6. [1] 158214-0020 SPEED DROOP ADJUSTER
70/7. [1] 014020-5120 PLAIN WASHER
70/8. [1] 029320-5030 TAB WASHER
70/9. [1] 010535-1220 FLAT-HEAD SCREW
85. [1] 158814-1200 SPEED CONTROL SHAFT
86. [1] 158823-0300 BUSHING
87. [1] 158322-0200 COILED SPRING
88. [1] 158710-0400 STRAP
89. [1] 029404-5010 BEARING PIN
91. [1] 158712-2000 CONTROL LEVER
93. [1] 029010-5210 BLEEDER SCREW
95. [1] 158211-0100 STRAP
96. [2] 158653-0100 WIRE
104. [1] 158017-0900 GASKET
105. [1] 158963-8020 GOVERNOR MOTOR ASSY
105/1. [1] 158962-5210 CASE
105/2. [1] 158903-0200 HOLDER
105/3. [1] 158903-0300 HOLDER
105/4. [1] 158903-0400 FLAT-HEAD SCREW
105/5. [1] 158903-1720 ADJUSTER
105/6. [2] 158903-0800 PLATE
105/7. [4] 029010-6330 BLEEDER SCREW M6P1.0L13
105/8. [1] 014020-8140 PLAIN WASHER D16&8.5T1.2
105/9. [1] 158904-0500 TOOTHED GEAR
105/10. [1] 158590-0000 BEARING PIN
105/11. [2] 020106-1640 BLEEDER SCREW M6P1.0L14
105/14. [1] 158904-0300 LEVER SHAFT
105/15. [1] 158904-0200 LEVER SHAFT
105/16. [3] 014020-8140 PLAIN WASHER D16&8.5T1.2
105/16. [3] 014020-8140 PLAIN WASHER D16&8.5T1.2
105/16. [3] 014020-8140 PLAIN WASHER D16&8.5T1.2
105/17. [3] 015320-1540 SPLIT PIN
105/18. [2] 158904-0400 TOOTHED GEAR
105/18. [2] 158904-0400 TOOTHED GEAR
105/19. [3] 011005-0820 SET OF NUTS
105/19. [3] 011005-0820 SET OF NUTS
105/20. [1] 158904-1920 ROUND NUT
105/21. [1] 158916-0000 SET OF NUTS
105/24. [1] 158908-3900 CONDENSER
105/25. [2] 014110-3440 LOCKING WASHER
105/26. [2] 012153-0840 FLAT-HEAD SCREW M3P0.5L8
105/27. [1] 158906-1500 TERMINAL BOARD
105/28. [2] 014020-4140 PLAIN WASHER D8&4.5T0.5
105/29. [2] 014110-4440 LOCKING WASHER
105/30. [2] 012154-1040 FLAT-HEAD SCREW M4P0.7L10
105/31. [1] 158902-0300 JOINT CONNECTION
105/32. [1] 158902-0020 FRICTION COUPLING
105/34. [1] 158908-2900 GEAR HEAD
105/35. [1] 158908-4200 MOTOR
105/36. [4] 014020-4140 PLAIN WASHER D8&4.5T0.5
105/37. [4] 158901-8100 FLAT-HEAD SCREW
105/38. [1] 158901-2200 HOSE
105/39. [1] 158901-8300 COVER
105/40. [1] 158900-0300 BRACKET
105/41. [3] 158900-0200 BUSHING
105/42. [3] 029010-6350 BLEEDER SCREW M6P1.0L22
105/43. [1] 158907-1820 LIMIT SWITCH
105/44. [1] 158907-1720 LIMIT SWITCH
105/46. [4] 020144-1240 BLEEDER SCREW
105/47. [5] 158906-0801 TERMINAL
105/48. [1] 158562-2600 COVER
105/49. [4] 014020-6140 PLAIN WASHER
105/50. [4] 014110-6440 LOCKING WASHER
105/51. [4] 158909-0100 BLEEDER SCREW
105/53. [2] 158901-2700 PLAIN WASHER
105/54. [1] 158901-2800 PACKING
105/55. [1] 158901-2600 GROUND
105/59. [2] 014110-4440 LOCKING WASHER
105/60. [2] 012154-1640 FLAT-HEAD SCREW
105/61. [1] 158906-1600 SPACER BUSHING
105/62. [1] 158901-2000 WIRE
105/63. [1] 158901-1800 WIRE
112. [1] 026512-1640 GASKET D15.9&12.2T1
113. [1] 155406-0220 AIR FILTER
118. [1] 158527-0200 NEEDLE VALVE
119. [1] 016500-0710 O-RING
123. [2] 026512-1640 GASKET D15.9&12.2T1
124. [2] 029111-2070 CAPSULE M12P1.5L10
130. [1] 029331-8040 GASKET
131. [1] 158660-0320 CONTROL VALVE
135. [1] 158515-0900 INDICATOR PLATE
137. [1] 158515-1000 INDICATOR PLATE
140. [2] 158820-0620 POINTER
140. [2] 158820-0620 POINTER
142. [2] 158820-0620 POINTER
142. [2] 158820-0620 POINTER
163. [1] 010210-1420 HEX-SOCKET-HEAD CAP SCREW
164. [1] 026510-1340 GASKET D13.4&10.2T1
190. [1] 158017-1000 GASKET
200. [1] 158599-4820 SPARE PART

Include in #2:

105866-7012 as INJECTION-PUMP ASSEMBLY

Cross reference number

Zexel num
Bosch num
Firm num
Name
105866-7012 
105866-7221 
F 019 Z2E 488 
   
HYDRAULIC GOVERNOR
* K




Information:

Coolant
To prevent personal injury, do not step up on engine to remove the filler cap, if applicable. Use an adequate ladder.At operating temperature, the engine coolant is hot and under pressure. The radiator and all lines to heaters or the engine contain hot water. When pressure is relieved rapidly, this hot water can turn into steam.Allow cooling system components to cool before draining.Any contact with hot water or steam can cause severe burns.Check the coolant level only after the engine has been stopped and the filler cap is cool enough to remove with your bare hand.Remove the cooling system filler cap slowly to relieve pressure.Cooling system supplemental additive contains alkali. To prevent personal injury, avoid contact with the skin and eyes and do not drink.Oils
Hot oil and components can cause personal injury. Do not allow hot oil or components to contact the skin.Batteries
Battery electrolyte contains acid and can cause injury. Avoid contact with the skin and eyes.Wash hands after touching batteries and connectors. Use of gloves is recommended.Batteries give off flammable fumes which can explode.Always thaw a frozen battery before jump starting. Frozen batteries can explode.Do not smoke when observing the battery electrolyte levels.Always wear protective glasses when working with batteries.Fire or Explosion Prevention
Determine whether the engine will be operated in an environment in which combustible gases could be drawn through the air inlet system. These gases could cause the engine to overspeed, which in turn could seriously damage the engine and result in bodily injury or property damage.If your application involves the presence of combustible gases, consult your Caterpillar dealer to obtain additional information concerning protection devices suitable for the application involved.Inhaling freon gas through a lit cigarette or other smoking method, or inhaling fumes released from a flame contacting freon could cause bodily harm or death. Do not smoke when servicing, charging or working around air conditioners or where freon gas may be present.All fuels, most lubricants and some coolant mixtures are flammable.Diesel fuel is flammable. Gasoline is flammable. The mixture of diesel and gasoline fumes are extremely explosive.Do not smoke while refueling or in a refueling area.Always thaw a frozen battery before jump starting. Frozen batteries can explode.Do not smoke in areas where batteries are charged, or where flammable materials are stored.Batteries give off flammable fumes which can explode.Keep all fuels and lubricants stored in properly marked containers and away from all unauthorized persons.Store all oily rags or other flammable material in a protective container, in a safe place.Do not weld or flame cut on pipes or tubes that contain flammable fluids. Clean them thoroughly with nonflammable solvent before welding or flame cutting on them.Remove all flammable materials such as fuel, oil and other debris before they accumulate on the truck engine.Do not expose the engine to flames, burning brush, etc., if at all possible.Exhaust shields (if equipped), which protect hot exhaust components from oil or fuel spray in the event of a line, tube or seal failure, must be installed correctly.Never disconnect any charging

Have questions with 105866-7012?





Group cross 105866-7012 ZEXEL

F 019 Z2E 487 
RHD10-MCL 
 
HYDRAULIC GOVERNOR
105866-7012  

105866-7221 
F 019 Z2E 488 
 
HYDRAULIC GOVERNOR
F 019 Z2E 489 
RHD10-MCL 
 
HYDRAULIC GOVERNOR
F 019 Z2E 490 
 
HYDRAULIC GOVERNOR
F 019 Z2E 491 
 
HYDRAULIC GOVERNOR
F 01G 29N 0BM 
RHD10-MCL 
 
HYDRAULIC GOVERNOR

Daihatsu 

F 019 Z2E 492 
QGDK307270FZ 
HYDRAULIC GOVERNOR
 
 
HYDRAULIC GOVERNOR

Fuji-Diesel 

 
A35611 
HYDRAULIC GOVERNOR
F 019 Z2E 493 
RHD10-MCL 
 
HYDRAULIC GOVERNOR

Daihatsu 

F 019 Z2E 494 
QGDK301150FZ 
HYDRAULIC GOVERNOR
F 01G 29N 0BN 
RHD10-MCL 
 
HYDRAULIC GOVERNOR
Back to top