105866-4130 ZEXEL F 019 Z2E 434 BOSCH HYDRAULIC GOVERNOR f019z2e434 1058664130


 

Information hydraulic governor

BOSCH F 019 Z2E 434 f019z2e434
ZEXEL 105866-4130 1058664130
105866-4130 HYDRAULIC GOVERNOR
Rating:
22
Buy HYDRAULIC GOVERNOR 105866-4130 zexel genuine, new aftermarket engine parts with delivery

Components :

0. INJECTION-PUMP ASSEMBLY 105866-4130
1. _
2. FUEL INJECTION PUMP
3. NUMBER PLATE
4. _
5. CAPSULE
6. ADJUSTING DEVICE
7. NOZZLE AND HOLDER ASSY
8. Nozzle and Holder
9. Open Pre:MPa(Kqf/cm2)
10. NOZZLE-HOLDER
11. NOZZLE

Scheme ###:

1. [1] 158502-0420 BASE
2. [1] 029811-8000 BEARING PLATE
3. [1] 158528-0900 PACKING RING
7. [1] 158131-0100 GEAR SHAFT
10. [1] 158028-0000 O-RING
11. [1] 158507-1920 DIAPHRAGM HOUSING
13. [1] 158621-0600 SLIDING PIECE
18. [1] 158699-0621 COMPENSATOR ASSY
18/1. [1] 158610-1101 POWER PISTON
18/3. [1] 158654-0800 COILED SPRING
18/4. [1] 158614-0700 STOP PIN
18/5. [1] 158612-0500 PLAIN WASHER
18/6. [1] 158654-0900 COILED SPRING
18/7. [1] 016110-1220 LOCKING WASHER
18/8. [1] 158612-0401 BUSHING
18/9. [2] 016550-2310 O-RING
18/10. [1] 158615-0500 PUMP PLUNGER
18/11. [1] 025620-1410 SPRING PIN
35. [3] 029330-6070 GASKET
36. [3] 010206-2520 HEX-SOCKET-HEAD CAP SCREW
50. [1] 158600-1020 FLYWEIGHT ASSEMBLY
51. [1] 158106-0100 PLAIN WASHER
52. [1] 029811-0000 BEARING PLATE
53. [1] 158620-1220 PILOT VALVE
60. [2] 158220-0000 GUIDE LEVER
61. [2] 158736-0200 BEARING PIN
62. [4] 025520-1510 SPLIT PIN
70. [1] 158730-0220 TERMINAL ARM
70/1. [1] 158230-0020 TERMINAL ARM
70/2. [1] 158315-0200 TERMINAL SHAFT
70/3. [1] 158315-0200 TERMINAL SHAFT
70/4. [2] 158736-0100 TAPER PIN
70/5. [2] 011006-0620 SET OF NUTS
70/6. [1] 158214-0020 SPEED DROOP ADJUSTER
70/7. [1] 014020-5120 PLAIN WASHER
70/8. [1] 029320-5030 TAB WASHER
70/9. [1] 010535-1220 FLAT-HEAD SCREW
85. [1] 158814-0900 SPEED CONTROL SHAFT
86. [2] 158823-0300 BUSHING
86. [2] 158823-0300 BUSHING
87. [1] 158322-0200 COILED SPRING
88. [1] 158710-0400 STRAP
89. [1] 029404-5010 BEARING PIN
95. [1] 158211-0100 STRAP
96. [2] 158653-0100 WIRE
104. [1] 158017-0900 GASKET
105. [1] 158562-8420 PNEUMATIC CONTROLLER
105/1. [1] 158562-4600 COVER
105/2. [1] 158910-0200 CYLINDER
105/3. [3] 029050-6090 FLAT-HEAD SCREW
105/4. [1] 014110-6440 LOCKING WASHER
105/5. [1] 158416-0000 FLAT-HEAD SCREW
105/6. [1] 158915-0700 UNION NUT
105/7. [1] 158918-0000 PLAIN WASHER D30&10.8T1.00
105/8. [1] 158912-1800 COILED SPRING K3.4
105/9. [1] 158412-0000 COILED SPRING K7.0
105/10. [1] 158918-0000 PLAIN WASHER D30&10.8T1.00
105/11. [1] 158413-0001 STOP PIN
105/12. [1] 158414-0000 PUMP PLUNGER
105/13. [1] 158414-0100 DIAPHRAGM
105/14. [1] 158414-0200 PLATE
105/15. [1] 013020-6040 UNION NUT M6P1H5
105/16. [1] 158910-0300 CAP
105/17. [1] 158915-1000 FLAT-HEAD SCREW
105/18. [1] 029630-9050 O-RING
105/19. [1] 158567-1500 WING NUT
105/21. [1] 158904-2020 ROUND NUT
105/22. [1] 158916-0000 SET OF NUTS
105/23. [2] 029050-6220 FLAT-HEAD SCREW
105/24. [2] 029320-6010 LOCKING WASHER
105/25. [2] 158909-0200 BLEEDER SCREW
105/26. [1] 027114-1040 INLET UNION
105/27. [2] 029331-4120 GASKET D18&14.2T1.5
105/28. [1] 027414-2640 EYE BOLT
105/30. [1] 013020-6040 UNION NUT M6P1H5
105/31. [1] 158567-1200 SET OF NUTS
105/35. [1] 026512-1640 GASKET D15.9&12.2T1
105/36. [1] 158066-0000 BLEEDER SCREW
106. [4] 029010-6350 BLEEDER SCREW M6P1.0L22
118. [1] 158527-0200 NEEDLE VALVE
119. [1] 016500-0710 O-RING
123. [2] 026512-1640 GASKET D15.9&12.2T1
124. [2] 029111-2070 CAPSULE M12P1.5L10
130. [1] 029331-8040 GASKET
131. [1] 158660-0320 CONTROL VALVE
135. [1] 158515-0900 INDICATOR PLATE
137. [1] 158515-1000 INDICATOR PLATE
140. [1] 158820-0620 POINTER
142. [1] 158820-0620 POINTER
158. [1] 015040-0880 BEARING PIN
163. [1] 010210-1420 HEX-SOCKET-HEAD CAP SCREW
164. [1] 026510-1340 GASKET D13.4&10.2T1
190. [1] 158017-1000 GASKET
200. [1] 158599-7320 SPARE PART

Include in #2:

105866-4130 as INJECTION-PUMP ASSEMBLY

Cross reference number

Zexel num
Bosch num
Firm num
Name
105866-4130 
F 019 Z2E 434 
   
HYDRAULIC GOVERNOR
* K




Information:

Coolant
At operating temperature, the engine coolant is hot and under pressure. The cooling system and all lines to heaters or the engine contain hot liquid. When pressure is relieved rapidly, this hot liquid can turn into steam.Allow cooling system components to cool before draining. Any contact with hot liquid or steam can cause severe burns. Check the coolant level only after the engine has been stopped and the vent release valve is cool enough to remove with your bare hand.Remove the cooling system vent release valve slowly to relieve pressure. Use caution when removing vent release valve, grease fittings, pressure taps, breathers or drain plugs. Hold a rag over the cap or plug to prevent being sprayed or splashed by liquids under pressure.Cooling system additive (conditioner) contains alkali. To prevent personal injury, avoid contact with the skin and eyes and do not drink.Oils
Hot oil and components can cause personal injury. Do not allow hot oil or components to contact the skin.Keep all exhaust manifold and turbocharger shields in place to protect hot exhaust from oil spray in the event of a line, tube or seal failure.Batteries
Always wear protective glasses when working with batteries. Battery electrolyte contains acid and can cause injury. Avoid contact with the skin and eyes.Wash hands after touching batteries and connectors. Use of gloves is recommended.Do not smoke when observing the battery electrolyte levels. Batteries give off flammable fumes which can explode. Ensure there is proper ventilation for batteries which are located in an enclosure.Never disconnect any charging unit circuit or battery circuit cable from the battery when charging unit is operating. A spark can cause the flammable vapor mixture of hydrogen and oxygen to explode.Fire or Explosion Prevention
Fire may result from lubricating oil or fuel sprayed on hot surfaces causing personal injury and property damage. Inspect all lines and tubes for wear or deterioration. They must be routed, supported or clamped securely. Tighten all connections to the recommended torque. Leaks can cause fires.Determine whether the engine will be operated in an environment in which combustible gases could be drawn through the air inlet system. These gases could cause the engine to overspeed, which in turn could seriously damage the engine and result in bodily injury or property damage.If your application involves the presence of combustible gases, consult your Caterpillar dealer to obtain additional information concerning protection devices suitable for the application involved.All fuels, most lubricants and some coolant mixtures are flammable. Diesel fuel is flammable. Gasoline is flammable. The mixture of diesel and gasoline fumes are extremely explosive.Do not smoke while refueling or in a refueling area.Do not smoke in areas where batteries are charged, or where flammable materials are stored.Always thaw a frozen battery before jump starting. Frozen batteries may explode. Batteries give off flammable fumes which can explode.Keep all fuels and lubricants stored in properly marked containers and away from all unauthorized persons.Store all oily rags or other flammable material in a protective container, in a safe place.Do not weld or flame

Have questions with 105866-4130?





Group cross 105866-4130 ZEXEL

F 019 Z2E 430 
RHD10-PC 
 
HYDRAULIC GOVERNOR
F 019 Z2E 431 
 
HYDRAULIC GOVERNOR

Hanshin 

F 019 Z2E 432 
RHD10-PC 
S579103 
HYDRAULIC GOVERNOR
F 019 Z2E 433 
RHD10-PC 
 
HYDRAULIC GOVERNOR
105866-4130  
F 019 Z2E 434 
 
HYDRAULIC GOVERNOR
F 019 Z2E 435 
RHD10-PC 
 
HYDRAULIC GOVERNOR
F 019 Z2E 436 
RHD10-PC 
 
HYDRAULIC GOVERNOR
F 019 Z2E 437 
 
HYDRAULIC GOVERNOR
F 019 Z2E 438 
RHD10-PC 
 
HYDRAULIC GOVERNOR
F 019 Z2E 439 
RHD10-PC 
 
HYDRAULIC GOVERNOR
F 019 Z2E 440 
 
HYDRAULIC GOVERNOR
Back to top