105866-4051 ZEXEL F 019 Z2E 426 BOSCH HYDRAULIC GOVERNOR f019z2e426 1058664051


 

Information hydraulic governor

BOSCH F 019 Z2E 426 f019z2e426
ZEXEL 105866-4051 1058664051
105866-4051 HYDRAULIC GOVERNOR
Rating:
13
Buy HYDRAULIC GOVERNOR 105866-4051 zexel genuine, new aftermarket engine parts with delivery

Components :

0. INJECTION-PUMP ASSEMBLY 105866-4051
1. _
2. FUEL INJECTION PUMP
3. NUMBER PLATE
4. _
5. CAPSULE
6. ADJUSTING DEVICE
7. NOZZLE AND HOLDER ASSY
8. Nozzle and Holder
9. Open Pre:MPa(Kqf/cm2)
10. NOZZLE-HOLDER
11. NOZZLE

Scheme ###:

1. [1] 158502-0420 BASE
2. [1] 029811-8000 BEARING PLATE
3. [1] 158528-0900 PACKING RING
7. [1] 158131-0100 GEAR SHAFT
10. [1] 158028-0000 O-RING
11. [1] 158507-1920 DIAPHRAGM HOUSING
13. [1] 158621-0800 SLEEVE
18. [1] 158699-0621 COMPENSATOR ASSY
18/1. [1] 158610-1101 POWER PISTON
18/3. [1] 158654-0800 COILED SPRING
18/4. [1] 158614-0700 STOP PIN
18/5. [1] 158612-0500 PLAIN WASHER
18/6. [1] 158654-0900 COILED SPRING
18/7. [1] 016110-1220 LOCKING WASHER
18/8. [1] 158612-0401 BUSHING
18/9. [2] 016550-2310 O-RING
18/10. [1] 158615-0500 PUMP PLUNGER
18/11. [1] 025620-1410 SPRING PIN
35. [3] 029330-6070 GASKET
36. [3] 010206-2520 HEX-SOCKET-HEAD CAP SCREW
50. [1] 158600-0720 FLYWEIGHT ASSEMBLY
51. [1] 158106-0100 PLAIN WASHER
52. [1] 029811-0000 BEARING PLATE
53. [1] 158620-1220 PILOT VALVE
60. [2] 158220-0000 GUIDE LEVER
61. [2] 158736-0200 BEARING PIN
62. [4] 025520-1510 SPLIT PIN
70. [1] 158730-0220 TERMINAL ARM
70/1. [1] 158230-0020 TERMINAL ARM
70/2. [1] 158315-0200 TERMINAL SHAFT
70/3. [1] 158315-0200 TERMINAL SHAFT
70/4. [2] 158736-0100 TAPER PIN
70/5. [2] 011006-0620 SET OF NUTS
70/6. [1] 158214-0020 SPEED DROOP ADJUSTER
70/7. [1] 014020-5120 PLAIN WASHER
70/8. [1] 029320-5030 TAB WASHER
70/9. [1] 010535-1220 FLAT-HEAD SCREW
85. [1] 158814-0900 SPEED CONTROL SHAFT
86. [2] 158823-0300 BUSHING
86. [2] 158823-0300 BUSHING
87. [1] 158322-0200 COILED SPRING
88. [1] 158710-0400 STRAP
89. [1] 029404-5010 BEARING PIN
95. [1] 158211-0100 STRAP
96. [2] 158653-0100 WIRE
104. [1] 158017-0900 GASKET
105. [1] 158962-7820 PNEUMATIC CONTROLLER
105/1. [1] 158562-4600 COVER
105/2. [1] 158910-0200 CYLINDER
105/3. [3] 029050-6090 FLAT-HEAD SCREW
105/4. [1] 014110-6440 LOCKING WASHER
105/5. [1] 158416-0000 FLAT-HEAD SCREW
105/6. [1] 158915-0700 UNION NUT
105/7. [1] 158918-0000 PLAIN WASHER D30&10.8T1.00
105/8. [1] 158412-0200 COILED SPRING K2.0
105/9. [1] 158912-0600 COILED SPRING K5.1
105/10. [1] 158918-0000 PLAIN WASHER D30&10.8T1.00
105/11. [1] 158413-0001 STOP PIN
105/12. [1] 158414-0000 PUMP PLUNGER
105/13. [1] 158414-0100 DIAPHRAGM
105/14. [1] 158414-0200 PLATE
105/15. [1] 013020-6040 UNION NUT M6P1H5
105/16. [1] 158910-0300 CAP
105/17. [1] 158915-1000 FLAT-HEAD SCREW
105/18. [1] 029630-9050 O-RING
105/19. [1] 158567-1500 WING NUT
105/21. [1] 158904-2020 ROUND NUT
105/22. [1] 158916-0000 SET OF NUTS
105/23. [2] 029050-6220 FLAT-HEAD SCREW
105/24. [2] 029320-6010 LOCKING WASHER
105/25. [2] 158909-0200 BLEEDER SCREW
105/26. [1] 027114-1040 INLET UNION
105/27. [2] 029331-4120 GASKET D18&14.2T1.5
105/28. [1] 027414-2640 EYE BOLT
105/30. [1] 013020-6040 UNION NUT M6P1H5
105/31. [1] 158567-1200 SET OF NUTS
105/35. [1] 026512-1640 GASKET D15.9&12.2T1
105/36. [1] 158066-0000 BLEEDER SCREW
106. [4] 029010-6350 BLEEDER SCREW M6P1.0L22
118. [1] 158527-0200 NEEDLE VALVE
119. [1] 016500-0710 O-RING
123. [2] 026512-1640 GASKET D15.9&12.2T1
123. [2] 026512-1640 GASKET D15.9&12.2T1
124. [2] 029111-2070 CAPSULE M12P1.5L10
124. [2] 029111-2070 CAPSULE M12P1.5L10
130. [1] 029331-8040 GASKET
131. [1] 158660-0320 CONTROL VALVE
135. [1] 158515-0900 INDICATOR PLATE
137. [1] 158515-1000 INDICATOR PLATE
140. [1] 158820-0620 POINTER
142. [1] 158820-0620 POINTER
158. [1] 015040-0880 BEARING PIN
163. [1] 010210-1420 HEX-SOCKET-HEAD CAP SCREW
164. [1] 026510-1340 GASKET D13.4&10.2T1
190. [1] 158017-1000 GASKET
200. [1] 158599-7320 SPARE PART

Include in #2:

105866-4051 as INJECTION-PUMP ASSEMBLY

Cross reference number

Zexel num
Bosch num
Firm num
Name
105866-4051 
F 019 Z2E 426 
RHD10-PC 
   
HYDRAULIC GOVERNOR
K 35CA HYDRAULIC GOVERNOR Hydraulic RHD10 Others




Information:

All PM Level 3 maintenance is to be performed at the intervals specified in the Maintenance Management Schedule.Before proceeding with PM Level 3 maintenance, perform all PM Level 2, PM Level 1 and Daily maintenance requirements. You must read and understand the warnings and instructions contained in the Safety section of this manual before performing any operation or maintenance procedures.Air Compressor
Rebuild or Exchange
Visually check for fluid leaks.Our recommendation to maintain your air compressor before it fails will be less costly than repairing the air compressor after failure.If the engine is operated until the air compressor fails, additional damage to the engine could result. For example: A failed air compressor could contaminate the engine oil with particles of materials since engine oil also lubricates the air compressor. The circulation of these engine oil with particles of materials since engine oil also lubricates the air compressor. The circulation of these contaminates through the engine lubricating system could damage the engine's main and connecting rod bearings.Maintenance Options
Repair Kits - These useful kits can be obtained from your Caterpillar dealer. These kits include all the necessary parts, special tools and instructions to repair your air compressor in either your own maintenance shop or at your servicing dealer's facility. Repair kits simplify parts ordering, help speed repairs and reduce parts cost. Exchange - This is a cost cutting service that permits exchanging a worn air compressor for a dealer or OEM factory rebuilt air compressor on an over-the-counter basis. They are available when needed at a substantial savings in both time and money. New - Replace with a new air compressor.Caterpillar Recommendation
The most cost effective repair option is to rebuild the air compressor with a repair kit that can be obtained from your Caterpillar dealer.Refer to the Service Manual for your engine to remove and install the air compressor.Turbocharger
Rebuild or Exchange
The cost incurred to maintain your turbocharger before failure as recommended could be significantly less than if you wait until your turbocharger fails.By maintaining your turbocharger before failure, you will minimize unscheduled downtime and reduce the chances for potential damage to other engine parts. When you reduce the risk of unscheduled downtime and costly repairs, you conserve cash that can be budgeted for use more profitably elsewhere.If you choose to operate your engine until the turbocharger fails, your repair costs could be as much as twenty-five times or more compared to the repair before failure cost. This excessive cost is due to additional engine damage that could have been prevented.If the engine is operated until the turbocharger fails, severe damage to the turbocharger's compressor wheel and/or engine could result.For example: severe damage to the turbocharger compressor wheel could cause parts from the compressor wheel to enter the engine cylinder that could result in cracks in the cylinder head and cause additional damage to the piston, a piston seizure orother potential damage to valves and cylinder head.Our recommended maintenance intervals for performing preventive maintenance on your turbocharger are based on experience and gathered

Have questions with 105866-4051?





Group cross 105866-4051 ZEXEL

F 019 Z2E 423 
RHD10-PC 
 
HYDRAULIC GOVERNOR
 
 

 
 

F 019 Z2E 424 
RHD10-PC 
 
HYDRAULIC GOVERNOR
F 019 Z2E 425 
RHD10-PC 
 
HYDRAULIC GOVERNOR

Niigata-Urawa 

 
17720031A 
HYDRAULIC GOVERNOR
105866-4051  
F 019 Z2E 426 
RHD10-PC 
 
HYDRAULIC GOVERNOR
F 019 Z2E 427 
RHD10-PC 
 
HYDRAULIC GOVERNOR
F 019 Z2E 428 
RHD10-PC 
 
HYDRAULIC GOVERNOR
 
 

Niigata-Urawa 

F 019 Z2E 429 
74044132C 
HYDRAULIC GOVERNOR
Back to top