Information hydraulic governor
BOSCH
F 019 Z1F 187
f019z1f187
ZEXEL
105856-5132
1058565132
Rating:
Components :
0. | INJECTION-PUMP ASSEMBLY | 105856-5132 |
1. | _ | |
2. | FUEL INJECTION PUMP | |
3. | NUMBER PLATE | |
4. | _ | |
5. | CAPSULE | |
6. | ADJUSTING DEVICE | |
7. | NOZZLE AND HOLDER ASSY | |
8. | Nozzle and Holder | |
9. | Open Pre:MPa(Kqf/cm2) | |
10. | NOZZLE-HOLDER | |
11. | NOZZLE |
Scheme ###:
1. | [1] | 158502-0420 | BASE |
2. | [1] | 029811-8000 | BEARING PLATE |
3. | [1] | 158528-0900 | PACKING RING |
7. | [1] | 158131-0100 | GEAR SHAFT |
10. | [1] | 158028-0000 | O-RING |
11. | [1] | 158507-1120 | DIAPHRAGM HOUSING |
13. | [1] | 158621-0800 | SLEEVE |
18. | [1] | 158699-0521 | COMPENSATOR ASSY |
18/1. | [1] | 158610-0901 | POWER PISTON |
18/3. | [1] | 158654-1000 | COILED SPRING |
18/4. | [1] | 158614-0300 | STOP PIN |
18/5. | [1] | 158612-0500 | PLAIN WASHER |
18/6. | [1] | 158654-1100 | COILED SPRING |
18/7. | [1] | 016110-1220 | LOCKING WASHER |
18/8. | [1] | 158612-0001 | BUSHING |
18/9. | [2] | 158528-1300 | O-RING |
18/10. | [1] | 158615-0400 | PUMP PLUNGER |
18/11. | [1] | 025620-1410 | SPRING PIN |
35. | [3] | 029330-6070 | GASKET |
36. | [3] | 010206-2520 | HEX-SOCKET-HEAD CAP SCREW |
50. | [1] | 158600-1020 | FLYWEIGHT ASSEMBLY |
51. | [1] | 158106-0100 | PLAIN WASHER |
52. | [1] | 029811-0000 | BEARING PLATE |
53. | [1] | 158620-1220 | PILOT VALVE |
60. | [2] | 158220-0000 | GUIDE LEVER |
61. | [2] | 158736-0200 | BEARING PIN |
62. | [4] | 025520-1510 | SPLIT PIN |
70. | [1] | 158730-0220 | TERMINAL ARM |
70/1. | [1] | 158230-0020 | TERMINAL ARM |
70/2. | [1] | 158315-0200 | TERMINAL SHAFT |
70/3. | [1] | 158315-0200 | TERMINAL SHAFT |
70/4. | [2] | 158736-0100 | TAPER PIN |
70/5. | [2] | 011006-0620 | SET OF NUTS |
70/6. | [1] | 158214-0020 | SPEED DROOP ADJUSTER |
70/7. | [1] | 014020-5120 | PLAIN WASHER |
70/8. | [1] | 029320-5030 | TAB WASHER |
70/9. | [1] | 010535-1220 | FLAT-HEAD SCREW |
85. | [1] | 158814-1000 | SPEED CONTROL SHAFT |
86. | [2] | 158823-0300 | BUSHING |
86. | [2] | 158823-0300 | BUSHING |
87. | [1] | 158322-0200 | COILED SPRING |
88. | [1] | 158710-0400 | STRAP |
89. | [1] | 029404-5010 | BEARING PIN |
95. | [1] | 158211-0100 | STRAP |
96. | [2] | 158653-0100 | WIRE |
104. | [1] | 158017-0900 | GASKET |
105. | [1] | 158963-8521 | GOVERNOR MOTOR ASSY |
105/1. | [1] | 158964-9210 | CASE |
105/2. | [1] | 158903-1920 | SCREW |
105/5. | [1] | 158908-6600 | GEAR HEAD |
105/6. | [1] | 158908-5020 | MOTOR |
105/7. | [4] | 014020-4140 | PLAIN WASHER D8&4.5T0.5 |
105/8. | [4] | 158901-8100 | FLAT-HEAD SCREW |
105/9. | [1] | 158402-3020 | FRICTION COUPLING |
105/11. | [1] | 158908-3900 | CONDENSER |
105/12. | [2] | 014110-3440 | LOCKING WASHER |
105/13. | [2] | 012153-0840 | FLAT-HEAD SCREW M3P0.5L8 |
105/14. | [1] | 158404-1000 | LEVER SHAFT |
105/15. | [2] | 014020-8140 | PLAIN WASHER D16&8.5T1.2 |
105/16. | [1] | 158904-1920 | ROUND NUT |
105/17. | [1] | 158916-0000 | SET OF NUTS |
105/18. | [1] | 158404-1100 | TOOTHED GEAR |
105/19. | [2] | 011005-0820 | SET OF NUTS |
105/20. | [2] | 015320-1540 | SPLIT PIN |
105/21. | [1] | 158401-6400 | HOSE |
105/22. | [1] | 158401-5000 | WIRE |
105/23. | [2] | 158401-7300 | GASKET |
105/24. | [1] | 158401-7500 | GASKET |
105/25. | [1] | 158401-7400 | GROUND |
105/26. | [1] | 158962-7200 | COVER |
105/27. | [3] | 014110-5440 | LOCKING WASHER |
105/28. | [3] | 012155-1240 | FLAT-HEAD SCREW M5P0.8L12 |
105/29. | [1] | 158905-0000 | FILLER PIECE |
105/30. | [1] | 014110-8440 | LOCKING WASHER |
105/31. | [1] | 013020-8140 | UNION NUT M8P1.25H6.5 |
105/34. | [1] | 158906-1800 | CLAMP |
105/36. | [1] | 012154-1040 | FLAT-HEAD SCREW M4P0.7L10 |
105/37. | [1] | 014110-4440 | LOCKING WASHER |
105/40. | [1] | 013020-6040 | UNION NUT M6P1H5 |
105/41. | [1] | 158067-0100 | SET OF NUTS |
105/45. | [1] | 026512-1640 | GASKET D15.9&12.2T1 |
105/46. | [1] | 029111-2070 | CAPSULE M12P1.5L10 |
105/47. | [1] | 158901-6200 | ADAPTOR |
105/48. | [1] | 158901-6300 | GASKET |
105/49. | [1] | 158901-6400 | UNION NUT |
105/61. | [1] | 158950-0100 | TERMINAL |
105/120. | [1] | 158908-5100 | CABLE TIE |
106. | [3] | 029010-6350 | BLEEDER SCREW M6P1.0L22 |
115. | [1] | 029050-6310 | BLEEDER SCREW |
116. | [1] | 014110-6440 | LOCKING WASHER |
118. | [1] | 158527-0200 | NEEDLE VALVE |
119. | [1] | 016500-0710 | O-RING |
123. | [2] | 026512-1640 | GASKET D15.9&12.2T1 |
124. | [2] | 029111-2070 | CAPSULE M12P1.5L10 |
130. | [1] | 029331-8040 | GASKET |
131. | [1] | 158660-0320 | CONTROL VALVE |
135. | [1] | 158515-0700 | INDICATOR PLATE |
137. | [1] | 158515-0800 | INDICATOR PLATE |
140. | [1] | 158820-0620 | POINTER |
142. | [1] | 158820-0620 | POINTER |
163. | [1] | 010210-1420 | HEX-SOCKET-HEAD CAP SCREW |
164. | [1] | 026510-1340 | GASKET D13.4&10.2T1 |
190. | [1] | 158017-1000 | GASKET |
200. | [1] | 158599-6720 | SPARE PART |
Include in #2:
105856-5132
as INJECTION-PUMP ASSEMBLY
Cross reference number
Zexel num
Bosch num
Firm num
Name
HYDRAULIC GOVERNOR
* K 35AA HYDRAULIC GOVERNOR Hydraulic RHD6 Others
* K 35AA HYDRAULIC GOVERNOR Hydraulic RHD6 Others
Information:
The problems in this section are problems that do come about and are normally called "low power." These problems are not necessarily more common than engine problems, but they are possible problems which you need to read and check before an engine is disassembled.Read all of the items but make sure the first three are checked completely before making any engine test. Possible Causes/CorrectionsTachometer Error
To check, connect a tachometer of known accuracy to the engine. Run the engine and make a comparison of the readings of the vehicle and test tachometers. If vehicle tachometer is bad, make repairs as necessary or install a new tachometer.Engine Operated at High Altitude
Less oxygen at higher altitudes causes the engine horsepower to go down. There is no effect on the horsepower of the engine for the first 2280 m (7500 ft) above sea level of operation.Brakes Do Not Completely Release
Check the brakes by feeling all the brake drums. If the brakes of a wheel do not completely release, the brake drum for that wheel will be hotter than the brake drums for the other wheels. With the truck lifted with a jack, the wheels must have free rotation when turned by hand.Extra Engine Driven Equipment
Air compressors, hydraulic pumps, alternator, and other engine driven equipment that has damage, or that was not installed correctly, or that is not in correct adjustment, can take more horsepower to drive than expected. If necessary, disconnect the equipment and test the engine.Speedometer Error
A bad speedometer does not give the correct speed or the correct indication of fuel consumption. An indication of low speed can cause the operator to feel that he has a power problem.Speeds Too High
The need for more horsepower is easy to see as the speed of the vehicle is increased. This is especially true if the front of the vehicle has a large surface area. Application personnel can give you the horsepower necessary for different vehicle designs at different speeds.Overload On Vehicle
Application personnel can give you the horsepower needs for different vehicles.High Moving Resistance
Soft ground conditions cause a need for more horsepower. To see if the problem is the engine, test the vehicle on a surface known to be good, or test on a chassis dynamometer.High Wind Resistance
The horsepower needs for a truck can be divided into two parts. Part of the horsepower is used to move the vehicle and part is used to get through the resistance of the wind. The horsepower necessary to get through the resistance of the wind will increase as the vehicle is used at higher speeds. Vehicles with large front area have a higher wind resistance and take more horsepower than those with a small front area. Some types of trucks, for example those used for the transportation of automobiles and or boats have high wind resistance even if the front area is small. Moving against the wind has the same effect on wind resistance as does higher vehicle speed.Power Loss in Drive Gears
It is possible for a
To check, connect a tachometer of known accuracy to the engine. Run the engine and make a comparison of the readings of the vehicle and test tachometers. If vehicle tachometer is bad, make repairs as necessary or install a new tachometer.Engine Operated at High Altitude
Less oxygen at higher altitudes causes the engine horsepower to go down. There is no effect on the horsepower of the engine for the first 2280 m (7500 ft) above sea level of operation.Brakes Do Not Completely Release
Check the brakes by feeling all the brake drums. If the brakes of a wheel do not completely release, the brake drum for that wheel will be hotter than the brake drums for the other wheels. With the truck lifted with a jack, the wheels must have free rotation when turned by hand.Extra Engine Driven Equipment
Air compressors, hydraulic pumps, alternator, and other engine driven equipment that has damage, or that was not installed correctly, or that is not in correct adjustment, can take more horsepower to drive than expected. If necessary, disconnect the equipment and test the engine.Speedometer Error
A bad speedometer does not give the correct speed or the correct indication of fuel consumption. An indication of low speed can cause the operator to feel that he has a power problem.Speeds Too High
The need for more horsepower is easy to see as the speed of the vehicle is increased. This is especially true if the front of the vehicle has a large surface area. Application personnel can give you the horsepower necessary for different vehicle designs at different speeds.Overload On Vehicle
Application personnel can give you the horsepower needs for different vehicles.High Moving Resistance
Soft ground conditions cause a need for more horsepower. To see if the problem is the engine, test the vehicle on a surface known to be good, or test on a chassis dynamometer.High Wind Resistance
The horsepower needs for a truck can be divided into two parts. Part of the horsepower is used to move the vehicle and part is used to get through the resistance of the wind. The horsepower necessary to get through the resistance of the wind will increase as the vehicle is used at higher speeds. Vehicles with large front area have a higher wind resistance and take more horsepower than those with a small front area. Some types of trucks, for example those used for the transportation of automobiles and or boats have high wind resistance even if the front area is small. Moving against the wind has the same effect on wind resistance as does higher vehicle speed.Power Loss in Drive Gears
It is possible for a