105856-4231 ZEXEL F 019 Z2E 250 BOSCH HYDRAULIC GOVERNOR f019z2e250 1058564231 8706311000

Information hydraulic governor

BOSCH F 019 Z2E 250 f019z2e250

ZEXEL 105856-4231 1058564231

MITSUBISHI-HEAV 8706311000 8706311000

Price: query

Buy now
Add to cart Go to cart

Rating:

Buy HYDRAULIC GOVERNOR 105856-4231 zexel genuine, new aftermarket engine parts with delivery

Components :

0.	INJECTION-PUMP ASSEMBLY	105856-4231
1.	_
2.	FUEL INJECTION PUMP
3.	NUMBER PLATE
4.	_
5.	CAPSULE
6.	ADJUSTING DEVICE
7.	NOZZLE AND HOLDER ASSY
8.	Nozzle and Holder
9.	Open Pre:MPa(Kqf/cm2)
10.	NOZZLE-HOLDER
11.	NOZZLE

Scheme ###:

1.	[1]	158502-0420	BASE
2.	[1]	029811-8000	BEARING PLATE
3.	[1]	158528-0900	PACKING RING
7.	[1]	158131-0100	GEAR SHAFT
10.	[1]	158028-0000	O-RING
11.	[1]	158507-1820	DIAPHRAGM HOUSING
13.	[1]	158621-0500	SLEEVE
18.	[1]	158699-1021	COMPENSATOR ASSY
18/1.	[1]	158610-0901	POWER PISTON
18/3.	[1]	158654-0400	COILED SPRING
18/4.	[1]	158614-0300	STOP PIN
18/5.	[1]	158612-0500	PLAIN WASHER
18/6.	[1]	158654-0500	COILED SPRING
18/7.	[1]	016110-1220	LOCKING WASHER
18/8.	[1]	158612-0001	BUSHING
18/9.	[2]	158528-1300	O-RING
18/10.	[1]	158615-0900	PUMP PLUNGER
18/11.	[1]	025620-1410	SPRING PIN
35.	[3]	029330-6070	GASKET
36.	[3]	010206-2520	HEX-SOCKET-HEAD CAP SCREW
50.	[1]	158600-0720	FLYWEIGHT ASSEMBLY
51.	[1]	158106-0100	PLAIN WASHER
52.	[1]	029811-0000	BEARING PLATE
53.	[1]	158620-1420	PILOT VALVE
60.	[2]	158220-0000	GUIDE LEVER
61.	[2]	158736-0200	BEARING PIN
62.	[4]	025520-1510	SPLIT PIN
70.	[1]	158730-1020	TERMINAL ARM
70/1.	[1]	158230-0020	TERMINAL ARM
70/2.	[1]	158815-0400	TERMINAL SHAFT
70/3.	[1]	158815-0000	TERMINAL SHAFT
70/4.	[2]	158736-0100	TAPER PIN
70/5.	[2]	011006-0620	SET OF NUTS
70/6.	[1]	158214-0020	SPEED DROOP ADJUSTER
70/7.	[1]	014020-5120	PLAIN WASHER
70/8.	[1]	029320-5030	TAB WASHER
70/9.	[1]	010535-1220	FLAT-HEAD SCREW
85.	[1]	158814-1900	SPEED CONTROL SHAFT
86.	[2]	158823-0300	BUSHING
86.	[2]	158823-0300	BUSHING
87.	[1]	158322-0200	COILED SPRING
88.	[1]	158710-0400	STRAP
89.	[1]	029404-5010	BEARING PIN
95.	[1]	158211-0100	STRAP
96.	[2]	158653-0100	WIRE
104.	[1]	158017-0900	GASKET
105.	[1]	158963-9920	PNEUMATIC CONTROLLER
105/1.	[1]	158563-0920	COVER
105/2.	[1]	158910-0200	CYLINDER
105/3.	[3]	029050-6090	FLAT-HEAD SCREW
105/4.	[1]	014110-6440	LOCKING WASHER
105/5.	[1]	158416-0000	FLAT-HEAD SCREW
105/6.	[1]	158915-0700	UNION NUT
105/7.	[1]	158918-0000	PLAIN WASHER D30&10.8T1.00
105/8.	[1]	158412-0200	COILED SPRING K2.0
105/9.	[1]	158912-0600	COILED SPRING K5.1
105/10.	[1]	158918-0000	PLAIN WASHER D30&10.8T1.00
105/11.	[1]	158913-0220	STOP PIN
105/12.	[1]	158414-0000	PUMP PLUNGER
105/13.	[1]	158414-0100	DIAPHRAGM
105/14.	[1]	158414-0200	PLATE
105/15.	[1]	010006-1440	BLEEDER SCREW M6P1L14 4T
105/16.	[1]	158910-0700	CAP
105/17.	[1]	158915-1000	FLAT-HEAD SCREW
105/18.	[1]	029630-9050	O-RING
105/19.	[1]	158567-1500	WING NUT
105/21.	[1]	158904-2020	ROUND NUT
105/22.	[1]	158916-0000	SET OF NUTS
105/23.	[2]	029050-6220	FLAT-HEAD SCREW
105/24.	[2]	029320-6010	LOCKING WASHER
105/25.	[2]	158909-0200	BLEEDER SCREW
105/27.	[2]	026516-2040	GASKET D19.9&16.2T1
105/28.	[1]	027416-2840	EYE BOLT
105/30.	[1]	013020-6040	UNION NUT M6P1H5
105/31.	[1]	158567-1200	SET OF NUTS
105/35.	[1]	026512-1640	GASKET D15.9&12.2T1
105/36.	[1]	158066-0000	BLEEDER SCREW
105/40.	[1]	158567-0400	BLEEDER SCREW
105/41.	[1]	158565-0000	UNION NUT
106.	[4]	029010-6350	BLEEDER SCREW M6P1.0L22
118.	[1]	158027-0100	NEEDLE VALVE
119.	[1]	016500-0710	O-RING
123.	[2]	026512-1640	GASKET D15.9&12.2T1
123.	[2]	026512-1640	GASKET D15.9&12.2T1
124.	[2]	029111-2070	CAPSULE M12P1.5L10
124.	[2]	029111-2070	CAPSULE M12P1.5L10
130.	[1]	029331-8040	GASKET
131.	[1]	158660-0020	CONTROL VALVE
135.	[1]	158515-0700	INDICATOR PLATE
137.	[1]	158515-0800	INDICATOR PLATE
140.	[1]	158820-0820	POINTER
142.	[1]	158820-0820	POINTER
158.	[1]	015040-0880	BEARING PIN
190.	[1]	158017-1000	GASKET
200.	[1]	158599-6920	SPARE PART

Include in #2:

105856-4231 as INJECTION-PUMP ASSEMBLY

Cross reference number

Zexel num

Bosch num

Firm num

Name

105856-4231

F 019 Z2E 250
RHD6-PC

8706311000 MITSUBISHI-HEAV

HYDRAULIC GOVERNOR
K 35AA HYDRAULIC GOVERNOR Hydraulic RHD6 Others

Information:

ROCKER ARM SHAFT ASSEMBLY
1. Fuel return line (one each head). 2. Bolts and locks (four each head).4. Remove rocker arm shaft assembly (3). Remove push rods (4).
REMOVING ROCKER ARM SHAFT ASSEMBLY
3. Rocker arm shaft assembly (one each head). 4. Push rods (eight each head).Install Rocker Arm Shaft Assemblies
1. Lubricate the cam followers, push rods, and rocker arm shaft assembly with clean engine oil (SAE 30).2. Install push rods. Position the rocker arm shaft assembly on the cylinder head.3. Install the rocker arm shaft assembly retaining bolts and locks. Tighten bolts to 18 5 lb. ft. (2.5 0.7 mkg) and bend the locks.4. Install the fuel return line.5. Adjust the intake valve clearance to .015 in. (0.38 mm) and the exhaust valve clearance to .025 in. (0.64 mm).6. Install valve cover. Install valve cover retaining bolts and tighten bolts to 120 24 lb. in. (138 28 cm.kg).Disassemble Rocker Arm Shaft Assembly
1. Remove retaining bolts and locks from each end of rocker arm shaft assembly and disassemble the rocker arm shaft assembly.
ROCKER ARM SHAFT ASSEMBLY DISASSEMBLED
1. Rocker arm shaft. 2. Rivet. 3. Washers (eight). 4. Rocker arms (two per cylinder). 5. Adjusting screw. 6. Bracket. 7. Oil supply hole.Assemble Rocker Arm Shaft Assembly
1. The oil holes in shaft (1), arms (4) and bracket (6) must be clean and free of dirt or foreign material.2. Install adjusting screws (5) into rocker arms (4) so they extend .44 in. (11.2 mm) below arm. This will avoid forcing valves into piston crowns when rocker arm assembly is installed on cylinder head.
ROCKER ARM SHAFT ASSEMBLY
1. Rocker arm shaft. 2. Rivet. 3. Washers (eight). 4. Rocker arms (two per cylinder). 5. Adjusting screw. 6. Bracket. 7. Oil supply hole.3. Install arms (4) on shaft with washers (3) positioned as shown.4. Position shaft (1) and arms (4) into bracket (6) so screws (5) are on the same side of bracket (6) as oil supply hole (7). Rivet (2) must be on top when shaft (1) is positioned into bracket (6). Later rocker arm shaft assemblies have machined flats (8). The machined flats must be on top when shaft (1) is positioned into bracket (6).
LATER ROCKER ARM SHAFT ASSEMBLY
1. Rocker arm shaft. 6. Bracket. 8. Machined flats (four per shaft).