105856-4071 ZEXEL F 019 Z1F 144 BOSCH HYDRAULIC GOVERNOR f019z1f144 1058564071

Information hydraulic governor

BOSCH F 019 Z1F 144 f019z1f144

ZEXEL 105856-4071 1058564071

Price: query

Buy now
Add to cart Go to cart

Rating:

Buy HYDRAULIC GOVERNOR 105856-4071 zexel genuine, new aftermarket engine parts with delivery

Components :

0.	INJECTION-PUMP ASSEMBLY	105856-4071
1.	_
2.	FUEL INJECTION PUMP
3.	NUMBER PLATE
4.	_
5.	CAPSULE
6.	ADJUSTING DEVICE
7.	NOZZLE AND HOLDER ASSY
8.	Nozzle and Holder
9.	Open Pre:MPa(Kqf/cm2)
10.	NOZZLE-HOLDER
11.	NOZZLE

Scheme ###:

1.	[1]	158502-0420	BASE
2.	[1]	029811-8000	BEARING PLATE
3.	[1]	158528-0900	PACKING RING
7.	[1]	158131-0100	GEAR SHAFT
10.	[1]	158028-0000	O-RING
11.	[1]	158507-1120	DIAPHRAGM HOUSING
13.	[1]	158621-0600	SLIDING PIECE
18.	[1]	158699-0521	COMPENSATOR ASSY
18/1.	[1]	158610-0901	POWER PISTON
18/3.	[1]	158654-1000	COILED SPRING
18/4.	[1]	158614-0300	STOP PIN
18/5.	[1]	158612-0500	PLAIN WASHER
18/6.	[1]	158654-1100	COILED SPRING
18/7.	[1]	016110-1220	LOCKING WASHER
18/8.	[1]	158612-0001	BUSHING
18/9.	[2]	158528-1300	O-RING
18/10.	[1]	158615-0400	PUMP PLUNGER
18/11.	[1]	025620-1410	SPRING PIN
35.	[3]	029330-6070	GASKET
36.	[3]	010206-2520	HEX-SOCKET-HEAD CAP SCREW
50.	[1]	158600-1020	FLYWEIGHT ASSEMBLY
51.	[1]	158106-0100	PLAIN WASHER
52.	[1]	029811-0000	BEARING PLATE
53.	[1]	158620-1520	PILOT VALVE
60.	[2]	158220-0000	GUIDE LEVER
61.	[2]	158736-0200	BEARING PIN
62.	[4]	025520-1510	SPLIT PIN
70.	[1]	158730-0220	TERMINAL ARM
70/1.	[1]	158230-0020	TERMINAL ARM
70/2.	[1]	158315-0200	TERMINAL SHAFT
70/3.	[1]	158315-0200	TERMINAL SHAFT
70/4.	[2]	158736-0100	TAPER PIN
70/5.	[2]	011006-0620	SET OF NUTS
70/6.	[1]	158214-0020	SPEED DROOP ADJUSTER
70/7.	[1]	014020-5120	PLAIN WASHER
70/8.	[1]	029320-5030	TAB WASHER
70/9.	[1]	010535-1220	FLAT-HEAD SCREW
85.	[1]	158814-0900	SPEED CONTROL SHAFT
86.	[2]	158823-0300	BUSHING
86.	[2]	158823-0300	BUSHING
87.	[1]	158322-0200	COILED SPRING
88.	[1]	158710-0400	STRAP
89.	[1]	029404-5010	BEARING PIN
95.	[1]	158211-0100	STRAP
96.	[2]	158653-0100	WIRE
104.	[1]	158017-0900	GASKET
105.	[1]	158963-5420	PNEUMATIC CONTROLLER
105/1.	[1]	158562-4600	COVER
105/2.	[1]	158910-0200	CYLINDER
105/3.	[3]	029050-6090	FLAT-HEAD SCREW
105/4.	[1]	014110-6440	LOCKING WASHER
105/5.	[1]	158416-0000	FLAT-HEAD SCREW
105/6.	[1]	158915-0700	UNION NUT
105/7.	[1]	158918-0000	PLAIN WASHER D30&10.8T1.00
105/8.	[1]	158412-0300	COILED SPRING K3.0
105/8A.	[1]	158412-0100	COILED SPRING K1.0
105/8B.	[1]	158412-0400	COILED SPRING K4.0
105/8C.	[1]	158412-0500	COILED SPRING K5.0
105/9.	[1]	158912-0600	COILED SPRING K5.1
105/9A.	[1]	158912-3000	COILED SPRING K4.5
105/9B.	[1]	158912-3100	COILED SPRING K4.1
105/9C.	[1]	158912-3200	COILED SPRING K4.0
105/9D.	[1]	158912-1100	COILED SPRING K4.8
105/9E.	[1]	158912-1200	COILED SPRING K5.4
105/10.	[1]	158918-0000	PLAIN WASHER D30&10.8T1.00
105/11.	[1]	158413-0001	STOP PIN
105/12.	[1]	158414-0000	PUMP PLUNGER
105/13.	[1]	158414-0100	DIAPHRAGM
105/14.	[1]	158414-0200	PLATE
105/15.	[1]	013020-6040	UNION NUT M6P1H5
105/16.	[1]	158910-0300	CAP
105/17.	[1]	158915-1000	FLAT-HEAD SCREW
105/18.	[1]	029630-9050	O-RING
105/19.	[1]	158567-1500	WING NUT
105/21.	[1]	158904-2020	ROUND NUT
105/22.	[1]	158916-0000	SET OF NUTS
105/23.	[2]	029050-6220	FLAT-HEAD SCREW
105/24.	[2]	029320-6010	LOCKING WASHER
105/25.	[2]	158909-0200	BLEEDER SCREW
105/26.	[1]	027114-1040	INLET UNION
105/27.	[2]	029331-4120	GASKET D18&14.2T1.5
105/28.	[1]	027414-2640	EYE BOLT
105/30.	[1]	013020-6040	UNION NUT M6P1H5
105/31.	[1]	158567-1200	SET OF NUTS
105/35.	[1]	026512-1640	GASKET D15.9&12.2T1
105/36.	[1]	158066-0000	BLEEDER SCREW
106.	[4]	029010-6350	BLEEDER SCREW M6P1.0L22
118.	[1]	158527-0200	NEEDLE VALVE
119.	[1]	016500-0710	O-RING
123.	[2]	026512-1640	GASKET D15.9&12.2T1
123.	[2]	026512-1640	GASKET D15.9&12.2T1
124.	[2]	029111-2070	CAPSULE M12P1.5L10
124.	[2]	029111-2070	CAPSULE M12P1.5L10
130.	[1]	029331-8040	GASKET
131.	[1]	158660-0320	CONTROL VALVE
135.	[1]	158515-0700	INDICATOR PLATE
137.	[1]	158515-0800	INDICATOR PLATE
140.	[1]	158820-0620	POINTER
142.	[1]	158820-0620	POINTER
158.	[1]	015040-0880	BEARING PIN
163.	[1]	010210-1420	HEX-SOCKET-HEAD CAP SCREW
164.	[1]	026510-1340	GASKET D13.4&10.2T1
190.	[1]	158017-1000	GASKET
200.	[1]	158599-6920	SPARE PART

Include in #2:

105856-4071 as INJECTION-PUMP ASSEMBLY

Cross reference number

Zexel num

Bosch num

Firm num

Name

105856-4071

F 019 Z1F 144
RHD6-PC

HYDRAULIC GOVERNOR
* K

Information:

Timing Gear Cover
Refer to SERVICE GUIDE for Preliminary Information.Two 3/8" NC Forcing Screws.
TIMING GEAR COVER1 Loosen bolt (2). Use two 3/8" NC forcing screws to remove pulley hub (1).2 At installation, tighten bolt to 230 20 lb. ft. (31,8 2,8 m.kg), tap bolt head with a hammer, and again tighten bolt to 230 20 lb. ft. (31,8 2,8 m. kg).3 Heat a new bushing in 250°F. (121°C.) oil for two hours before installation.4 Shim between trunnion hub and support halves to obtain a fit of .002 in. (0,05 mm) loose-to-.003 in. (0,07 mm) tight.5 Trim gasket flush with bottom face of cylinder block. Gaskets will leak if not cut square and flush with oil pan face.Timing Gears
Refer to SERVICE GUIDE for Preliminary Information.8S5132 Puller Plate,8S5133 Expansion Plug,8S6470 Pressure Screw,8B7561 Step Plate,Two 3/8" NF bolts.
Do not rotate the crankshaft with camshaft gear removed.
1 Use an 8S5132 Puller Plate, 8S5133 Expansion Plug, 8B7561 Step Plate, two 3/8" NF bolts and an 8S6470 Pressure Screw to remove gear. At installation, refer to topic FUEL INJECTION PUMP CAMSHAFT TIMING - FUEL SYSTEM - TESTING AND ADJUSTING.2 Fuel transfer pump must be removed before removing shaft. At installation, accessory drive shaft must be timed to crankshaft. Refer to FUEL INJECTION PUMP CAMSHAFT TIMING - FUEL SYSTEM - TESTING AND ADJUSTING.3 Trim gasket flush with bottom face of cylinder block. Gasket will leak if not cut square and flush with oil pan face.4, 6 Bearing must be centered in gear hub.5 Install washer with concave side toward gear (1).7 Align letter "C" on camshaft gear with letter "C" on crankshaft gear.8 Camshaft front bearing must be recessed .06 in. (1,52 mm) from front face of bore, oil hole in bearing must align with oil hole in cylinder block, and joint in bearing must face cylinder block centerline. Intermediate bearings must be flush with front face of bearing bore. Rear bearing must be recessed .06 in. (1,52 mm) from rear face of bore.Flywheel And Flywheel Housing
Refer to SERVICE GUIDE for Preliminary Information.FT125 Pilot and FT638 Sleeve (Fabricated Tools),5H1504 Washer,2J3506 Nut. 1, 2 Align mark on flywheel with mark on crankshaft.3 Heat ring gear. Do not exceed 600°F. (315°C.). Install with chamfered portion of ring gear teeth toward starter pinion when flywheel is installed.4 Use FT125 Pilot, FT638 Sleeve, 5H1504 Washer and a 2J3506 Nut to install seal.5 Trim gasket flush with bottom face of cylinder block. Gasket will leak if not cut square and flush with oil pan face.
This is an example of installing the crankshaft rear seal. A-FT638 Sleeve. B-2J3506 Nut. C-5H1504 Washer. D-FT125 Pilot. Secure pilot to crankshaft with three 5/8"-18 NF bolts, 2 in. (50,8 mm) long. Grind bolt head as necessary to provide seal clearance.