105856-2880 ZEXEL F 019 Z2E 185 BOSCH HYDRAULIC GOVERNOR f019z2e185 1058562880

Information hydraulic governor

BOSCH F 019 Z2E 185 f019z2e185

ZEXEL 105856-2880 1058562880

Price: query

Buy now
Add to cart Go to cart

Rating:

Buy HYDRAULIC GOVERNOR 105856-2880 zexel genuine, new aftermarket engine parts with delivery

Components :

0.	INJECTION-PUMP ASSEMBLY	105856-2880
1.	_
2.	FUEL INJECTION PUMP
3.	NUMBER PLATE
4.	_
5.	CAPSULE
6.	ADJUSTING DEVICE
7.	NOZZLE AND HOLDER ASSY
8.	Nozzle and Holder
9.	Open Pre:MPa(Kqf/cm2)
10.	NOZZLE-HOLDER
11.	NOZZLE

Scheme ###:

1.	[1]	158502-0420	BASE
2.	[1]	029811-8000	BEARING PLATE
3.	[1]	158528-0900	PACKING RING
7.	[1]	158131-0100	GEAR SHAFT
10.	[1]	158028-0000	O-RING
11.	[1]	158507-1820	DIAPHRAGM HOUSING
13.	[1]	158621-0600	SLIDING PIECE
18.	[1]	158699-0521	COMPENSATOR ASSY
18/1.	[1]	158610-0901	POWER PISTON
18/3.	[1]	158654-1000	COILED SPRING
18/4.	[1]	158614-0300	STOP PIN
18/5.	[1]	158612-0500	PLAIN WASHER
18/6.	[1]	158654-1100	COILED SPRING
18/7.	[1]	016110-1220	LOCKING WASHER
18/8.	[1]	158612-0001	BUSHING
18/9.	[2]	158528-1300	O-RING
18/10.	[1]	158615-0400	PUMP PLUNGER
18/11.	[1]	025620-1410	SPRING PIN
35.	[3]	029330-6070	GASKET
36.	[3]	010206-2520	HEX-SOCKET-HEAD CAP SCREW
50.	[1]	158600-0720	FLYWEIGHT ASSEMBLY
51.	[1]	158106-0100	PLAIN WASHER
52.	[1]	029811-0000	BEARING PLATE
53.	[1]	158620-1220	PILOT VALVE
60.	[2]	158220-0000	GUIDE LEVER
61.	[2]	158736-0200	BEARING PIN
62.	[4]	025520-1510	SPLIT PIN
70.	[1]	158730-0220	TERMINAL ARM
70/1.	[1]	158230-0020	TERMINAL ARM
70/2.	[1]	158315-0200	TERMINAL SHAFT
70/3.	[1]	158315-0200	TERMINAL SHAFT
70/4.	[2]	158736-0100	TAPER PIN
70/5.	[2]	011006-0620	SET OF NUTS
70/6.	[1]	158214-0020	SPEED DROOP ADJUSTER
70/7.	[1]	014020-5120	PLAIN WASHER
70/8.	[1]	029320-5030	TAB WASHER
70/9.	[1]	010535-1220	FLAT-HEAD SCREW
85.	[1]	158814-0900	SPEED CONTROL SHAFT
86.	[2]	158823-0300	BUSHING
86.	[2]	158823-0300	BUSHING
87.	[1]	158322-0200	COILED SPRING
88.	[1]	158710-0400	STRAP
89.	[1]	029404-5010	BEARING PIN
95.	[1]	158211-0100	STRAP
96.	[2]	158653-0100	WIRE
104.	[1]	158017-0900	GASKET
105.	[1]	158963-1020	GOVERNOR MOTOR ASSY
105/1.	[1]	158962-5110	CASE
105/2.	[1]	158903-1920	SCREW
105/5.	[1]	158908-3800	GEAR HEAD
105/6.	[1]	158901-7800	MOTOR
105/7.	[4]	014020-4140	PLAIN WASHER D8&4.5T0.5
105/8.	[4]	158901-8100	FLAT-HEAD SCREW
105/9.	[1]	158402-3020	FRICTION COUPLING
105/14.	[1]	158404-1000	LEVER SHAFT
105/15.	[2]	014020-8140	PLAIN WASHER D16&8.5T1.2
105/16.	[1]	158904-1120	ROUND NUT
105/17.	[1]	158916-0000	SET OF NUTS
105/18.	[1]	158404-1100	TOOTHED GEAR
105/19.	[2]	011005-0820	SET OF NUTS
105/20.	[2]	015320-1540	SPLIT PIN
105/21.	[1]	158401-6400	HOSE
105/22.	[1]	158401-5000	WIRE
105/23.	[2]	158401-7300	GASKET
105/24.	[1]	158401-7500	GASKET
105/25.	[1]	158401-7400	GROUND
105/26.	[1]	158962-6100	COVER
105/27.	[3]	014110-5440	LOCKING WASHER
105/28.	[3]	012155-1240	FLAT-HEAD SCREW M5P0.8L12
105/29.	[1]	158905-0000	FILLER PIECE
105/30.	[1]	014110-8440	LOCKING WASHER
105/31.	[1]	013020-8140	UNION NUT M8P1.25H6.5
105/34.	[1]	158906-1400	CLAMP
105/35.	[1]	014110-4440	LOCKING WASHER
105/36.	[1]	012154-0840	FLAT-HEAD SCREW M4P0.7L8
105/37.	[1]	014110-4440	LOCKING WASHER
105/40.	[1]	013020-6040	UNION NUT M6P1H5
105/41.	[1]	158067-0100	SET OF NUTS
105/45.	[1]	026512-1640	GASKET D15.9&12.2T1
105/46.	[1]	029111-2070	CAPSULE M12P1.5L10
105/61.	[2]	158950-0100	TERMINAL
105/120.	[1]	158908-5100	CABLE TIE
106.	[3]	029010-6350	BLEEDER SCREW M6P1.0L22
115.	[1]	029050-6310	BLEEDER SCREW
116.	[1]	014110-6440	LOCKING WASHER
118.	[1]	158527-0200	NEEDLE VALVE
119.	[1]	016500-0710	O-RING
123.	[2]	026512-1640	GASKET D15.9&12.2T1
124.	[2]	029111-2070	CAPSULE M12P1.5L10
130.	[1]	029331-8040	GASKET
131.	[1]	158660-0320	CONTROL VALVE
135.	[1]	158515-0700	INDICATOR PLATE
137.	[1]	158515-0800	INDICATOR PLATE
140.	[1]	158820-0620	POINTER
142.	[1]	158820-0620	POINTER
190.	[1]	158017-1000	GASKET
200.	[1]	158599-6720	SPARE PART

Include in #2:

105856-2880 as INJECTION-PUMP ASSEMBLY

Cross reference number

Zexel num

Bosch num

Firm num

Name

105856-2880

F 019 Z2E 185
RHD6-MC

HYDRAULIC GOVERNOR
* K

Information:

3. Remove bearing caps (1) from the two connecting rods. Put pieces of rubber hose or tape on the threads of the connecting rod bolts as protection for the crankshaft. 4. Push the pistons up until the piston rings are clear of the cylinder liner. Remove pistons (2). Put identification on each piston as to its location for correct installation and alignment. Keep each cap with its connecting rod.
Do not turn the crankshaft while any of the connecting rods are in the engine without the caps installed.
5. Do Steps 1 through 4 for the remainder of the pistons.Install Pistons
1. Put clean engine oil on the piston rings, connecting rod bearings and cylinder liner. 2. Install piston into cylinder liner with tool (A). Push piston and rings through tool (A) with a hammer handle.3. Make a check of the connecting rod bearing clearance. See REMOVE AND INSTALL CONNECTING ROD BEARINGS. 4. Put clean engine oil on connecting rod cap and bearing. Install the cap (1) on the connecting rod. Tighten nuts to a torque of 50 5 lb. ft. (70 7 N m) plus 180°.5. Do Steps 1 through 4 for the remainder of the pistons.
As caps are installed, make sure that number identification on cap is on same side as number identification on rod.
end by: a) install cylinder head and spacer plateb) install oil pumpDisassemble Pistons
start by: a) remove pistons 1. Remove the retaining rings (2) for the piston pin.2. Remove piston pin (1) and remove piston from the connecting rod.3. Remove the piston rings using ring expander (A).Assemble Pistons
1. Use ring expander (A) to install the piston rings. The two compression rings have marks "UP-1" and "UP-2". The rings must be installed with the marks toward the top of the piston with "UP-1" being the top ring. Put the ring gaps in place 120° from each other.2. Put clean oil on the piston pin. Put the piston in place on the connecting rod. Install the piston pin and retaining rings. On some engines there can be a "V" mark (2) on the piston. This mark must be on the same side as the location number (1) on the connecting rod.end by: a) install pistons