105856-2381 ZEXEL F 019 Z2E 142 BOSCH HYDRAULIC GOVERNOR f019z2e142 1058562381

Information hydraulic governor

BOSCH F 019 Z2E 142 f019z2e142

ZEXEL 105856-2381 1058562381

Price: query

Buy now
Add to cart Go to cart

Rating:

Buy HYDRAULIC GOVERNOR 105856-2381 zexel genuine, new aftermarket engine parts with delivery

Components :

0.	INJECTION-PUMP ASSEMBLY	105856-2381
1.	_
2.	FUEL INJECTION PUMP
3.	NUMBER PLATE
4.	_
5.	CAPSULE
6.	ADJUSTING DEVICE
7.	NOZZLE AND HOLDER ASSY
8.	Nozzle and Holder
9.	Open Pre:MPa(Kqf/cm2)
10.	NOZZLE-HOLDER
11.	NOZZLE

Scheme ###:

1.	[1]	158502-0420	BASE
2.	[1]	029811-8000	BEARING PLATE
3.	[1]	158528-0900	PACKING RING
7.	[1]	158131-0100	GEAR SHAFT
10.	[1]	158028-0000	O-RING
11.	[1]	158507-1820	DIAPHRAGM HOUSING
13.	[1]	158621-0800	SLEEVE
18.	[1]	158699-0521	COMPENSATOR ASSY
18/1.	[1]	158610-0901	POWER PISTON
18/3.	[1]	158654-1000	COILED SPRING
18/4.	[1]	158614-0300	STOP PIN
18/5.	[1]	158612-0500	PLAIN WASHER
18/6.	[1]	158654-1100	COILED SPRING
18/7.	[1]	016110-1220	LOCKING WASHER
18/8.	[1]	158612-0001	BUSHING
18/9.	[2]	158528-1300	O-RING
18/10.	[1]	158615-0400	PUMP PLUNGER
18/11.	[1]	025620-1410	SPRING PIN
35.	[3]	029330-6070	GASKET
36.	[3]	010206-2520	HEX-SOCKET-HEAD CAP SCREW
50.	[1]	158600-0720	FLYWEIGHT ASSEMBLY
51.	[1]	158106-0100	PLAIN WASHER
52.	[1]	029811-0000	BEARING PLATE
53.	[1]	158620-1220	PILOT VALVE
60.	[2]	158220-0000	GUIDE LEVER
61.	[2]	158736-0200	BEARING PIN
62.	[4]	025520-1510	SPLIT PIN
70.	[1]	158730-0220	TERMINAL ARM
70/1.	[1]	158230-0020	TERMINAL ARM
70/2.	[1]	158315-0200	TERMINAL SHAFT
70/3.	[1]	158315-0200	TERMINAL SHAFT
70/4.	[2]	158736-0100	TAPER PIN
70/5.	[2]	011006-0620	SET OF NUTS
70/6.	[1]	158214-0020	SPEED DROOP ADJUSTER
70/7.	[1]	014020-5120	PLAIN WASHER
70/8.	[1]	029320-5030	TAB WASHER
70/9.	[1]	010535-1220	FLAT-HEAD SCREW
85.	[1]	158814-0900	SPEED CONTROL SHAFT
86.	[2]	158823-0300	BUSHING
86.	[2]	158823-0300	BUSHING
87.	[1]	158322-0200	COILED SPRING
88.	[1]	158710-0400	STRAP
89.	[1]	029404-5010	BEARING PIN
95.	[1]	158211-0100	STRAP
96.	[2]	158653-0100	WIRE
104.	[1]	158017-0900	GASKET
105.	[1]	158062-0321	GOVERNOR MOTOR ASSY
105/1.	[1]	158962-5110	CASE
105/2.	[1]	158903-1920	SCREW
105/5.	[1]	158908-2900	GEAR HEAD
105/6.	[1]	158908-4200	MOTOR
105/7.	[4]	014020-4140	PLAIN WASHER D8&4.5T0.5
105/8.	[4]	158901-8100	FLAT-HEAD SCREW
105/9.	[1]	158402-3020	FRICTION COUPLING
105/11.	[1]	158908-3900	CONDENSER
105/12.	[2]	014110-3440	LOCKING WASHER
105/13.	[2]	012153-0840	FLAT-HEAD SCREW M3P0.5L8
105/14.	[1]	158404-1000	LEVER SHAFT
105/15.	[2]	014020-8140	PLAIN WASHER D16&8.5T1.2
105/16.	[1]	158904-1920	ROUND NUT
105/17.	[1]	158916-0000	SET OF NUTS
105/18.	[1]	158404-1100	TOOTHED GEAR
105/19.	[2]	011005-0820	SET OF NUTS
105/20.	[2]	015320-1540	SPLIT PIN
105/21.	[1]	158401-6400	HOSE
105/22.	[1]	158401-5000	WIRE
105/23.	[2]	158401-7300	GASKET
105/24.	[1]	158401-7500	GASKET
105/25.	[1]	158401-7400	GROUND
105/26.	[1]	158962-6100	COVER
105/27.	[3]	014110-5440	LOCKING WASHER
105/28.	[3]	012155-1240	FLAT-HEAD SCREW M5P0.8L12
105/29.	[1]	158905-0000	FILLER PIECE
105/30.	[1]	014110-8440	LOCKING WASHER
105/31.	[1]	013020-8140	UNION NUT M8P1.25H6.5
105/34.	[1]	158906-1800	CLAMP
105/36.	[1]	012154-1040	FLAT-HEAD SCREW M4P0.7L10
105/37.	[1]	014110-4440	LOCKING WASHER
105/40.	[1]	013020-6040	UNION NUT M6P1H5
105/41.	[1]	158067-0100	SET OF NUTS
105/45.	[1]	026512-1640	GASKET D15.9&12.2T1
105/46.	[1]	029111-2070	CAPSULE M12P1.5L10
105/61.	[1]	158950-0100	TERMINAL
106.	[3]	029010-6350	BLEEDER SCREW M6P1.0L22
115.	[1]	029050-6310	BLEEDER SCREW
116.	[1]	014110-6440	LOCKING WASHER
118.	[1]	158527-0200	NEEDLE VALVE
119.	[1]	016500-0710	O-RING
123.	[2]	026512-1640	GASKET D15.9&12.2T1
124.	[2]	029111-2070	CAPSULE M12P1.5L10
130.	[1]	029331-8040	GASKET
131.	[1]	158660-0320	CONTROL VALVE
135.	[1]	158515-0700	INDICATOR PLATE
137.	[1]	158515-0800	INDICATOR PLATE
140.	[1]	158820-0620	POINTER
142.	[1]	158820-0620	POINTER
190.	[1]	158017-1000	GASKET
200.	[1]	158599-6720	SPARE PART

Include in #2:

105856-2381 as INJECTION-PUMP ASSEMBLY

Cross reference number

Zexel num

Bosch num

Firm num

Name

105856-2381

F 019 Z2E 142
RHD6-MC

HYDRAULIC GOVERNOR
K

Information:

start by:a) remove pistons 1. Remove bearings (3) from the connecting rod and connecting rod cap.2. Remove retainer ring (1) with tool (A).3. Remove pin (2) and connecting rod (4) from the piston. 4. Remove the piston rings (5) from the piston with tool (B). Clean the piston ring grooves on the pistons with an acceptable ring groove cleaning tool. See USE OF PISTON PIN BEARING REMOVAL AND INSTALLATION TOOLS, SPECIAL INSTRUCTIONS, Form No. SMHS7295.5. Heat the connecting rod (4) in an oven to a temperature of 350°-500°F (177°-260°C). Never use a direct flame to heat a connecting rod. 6. Put connecting rod (4) in position on the base plate of tooling (C). Put a new rod pin bearing (6) on the adapter part of tooling (C). The old bearing is pushed out by tooling (C) as the new bearing is installed.7. Use tooling (C) to push the new bearing into the connecting rod until the push adapter of tooling (C) makes full contact with the connecting rod surface.8. Use a pin boring machine to make the rod pin bearing the correct size. The bore in the new rod pin bearing must be 2.0012 .0003 in. (50.830 0.008 mm).9. Check the clearance between the ends of the piston rings. See PISTONS AND RINGS in SPECIFICATIONS.10. Install the oil ring spring in the oil ring groove of the piston. The oil ring is to be installed over the spring with the oil ring end gap 180° from the oil ring spring joint. 11. Install the oil ring on the piston with tool (B).12. Install the second (intermediate) piston ring with the side that has the identification "UP-2" toward the top of the piston with tool (B).13. Install the first (top) piston ring with the side that has the identification "UP-1" toward the top of the piston with tool (B). After the installation of all three piston rings, put the piston rings in position so the end gaps are 120° apart. 14. Put the piston in position on connecting rod (4). Put clean engine oil on pin (2) and install the pin. Install retainer rings (1) with tool (A). Make sure the retainer rings are in the grooves of the piston.15. Install bearings (3) in the connecting rod and connecting rod cap.end by:a) install pistons