Information hydraulic governor
BOSCH
F 019 Z1F 131
f019z1f131
ZEXEL
105856-2021
1058562021
Rating:
Components :
| 0. | INJECTION-PUMP ASSEMBLY | 105856-2021 |
| 1. | _ | |
| 2. | FUEL INJECTION PUMP | |
| 3. | NUMBER PLATE | |
| 4. | _ | |
| 5. | CAPSULE | |
| 6. | ADJUSTING DEVICE | |
| 7. | NOZZLE AND HOLDER ASSY | |
| 8. | Nozzle and Holder | |
| 9. | Open Pre:MPa(Kqf/cm2) | |
| 10. | NOZZLE-HOLDER | |
| 11. | NOZZLE |
Scheme ###:
| 1. | [1] | 158502-0420 | BASE |
| 2. | [1] | 029811-8000 | BEARING PLATE |
| 3. | [1] | 158528-0900 | PACKING RING |
| 7. | [1] | 158131-0100 | GEAR SHAFT |
| 10. | [1] | 158028-0000 | O-RING |
| 11. | [1] | 158507-1120 | DIAPHRAGM HOUSING |
| 13. | [1] | 158621-0500 | SLEEVE |
| 18. | [1] | 158699-0321 | COMPENSATOR ASSY |
| 18/1. | [1] | 158610-0901 | POWER PISTON |
| 18/3. | [1] | 158654-0400 | COILED SPRING |
| 18/4. | [1] | 158614-0300 | STOP PIN |
| 18/5. | [1] | 158612-0500 | PLAIN WASHER |
| 18/6. | [1] | 158654-0500 | COILED SPRING |
| 18/7. | [1] | 016110-1220 | LOCKING WASHER |
| 18/8. | [1] | 158612-0001 | BUSHING |
| 18/9. | [2] | 158528-1300 | O-RING |
| 18/10. | [1] | 158615-0300 | PUMP PLUNGER |
| 18/11. | [1] | 025620-1410 | SPRING PIN |
| 35. | [3] | 029330-6070 | GASKET |
| 36. | [3] | 010206-2520 | HEX-SOCKET-HEAD CAP SCREW |
| 50. | [1] | 158600-0720 | FLYWEIGHT ASSEMBLY |
| 51. | [1] | 158106-0100 | PLAIN WASHER |
| 52. | [1] | 029811-0000 | BEARING PLATE |
| 53. | [1] | 158620-1120 | PILOT VALVE |
| 60. | [2] | 158220-0000 | GUIDE LEVER |
| 61. | [2] | 158736-0200 | BEARING PIN |
| 62. | [4] | 025520-1510 | SPLIT PIN |
| 70. | [1] | 158730-0220 | TERMINAL ARM |
| 70/1. | [1] | 158230-0020 | TERMINAL ARM |
| 70/2. | [1] | 158315-0200 | TERMINAL SHAFT |
| 70/3. | [1] | 158315-0200 | TERMINAL SHAFT |
| 70/4. | [2] | 158736-0100 | TAPER PIN |
| 70/5. | [2] | 011006-0620 | SET OF NUTS |
| 70/6. | [1] | 158214-0020 | SPEED DROOP ADJUSTER |
| 70/7. | [1] | 014020-5120 | PLAIN WASHER |
| 70/8. | [1] | 029320-5030 | TAB WASHER |
| 70/9. | [1] | 010535-1220 | FLAT-HEAD SCREW |
| 85. | [1] | 158814-0900 | SPEED CONTROL SHAFT |
| 86. | [2] | 158823-0300 | BUSHING |
| 88. | [1] | 158710-0400 | STRAP |
| 89. | [1] | 029404-5010 | BEARING PIN |
| 95. | [1] | 158211-0100 | STRAP |
| 96. | [2] | 158653-0100 | WIRE |
| 104. | [1] | 158017-0900 | GASKET |
| 105. | [1] | 158062-0100 | COVER |
| 106. | [4] | 029010-6350 | BLEEDER SCREW M6P1.0L22 |
| 108. | [1] | 158567-1200 | SET OF NUTS |
| 109. | [1] | 013020-6040 | UNION NUT M6P1H5 |
| 110. | [1] | 158567-1200 | SET OF NUTS |
| 111. | [1] | 013020-6040 | UNION NUT M6P1H5 |
| 112. | [1] | 026512-1640 | GASKET D15.9&12.2T1 |
| 113. | [1] | 155406-0220 | AIR FILTER |
| 118. | [1] | 158027-0100 | NEEDLE VALVE |
| 119. | [1] | 016500-0710 | O-RING |
| 123. | [2] | 026512-1640 | GASKET D15.9&12.2T1 |
| 124. | [2] | 029111-2070 | CAPSULE M12P1.5L10 |
| 130. | [1] | 029331-8040 | GASKET |
| 131. | [1] | 158660-0320 | CONTROL VALVE |
| 135. | [1] | 158515-0700 | INDICATOR PLATE |
| 137. | [1] | 158515-0800 | INDICATOR PLATE |
| 140. | [1] | 158820-0620 | POINTER |
| 142. | [1] | 158820-0620 | POINTER |
| 163. | [1] | 010210-1420 | HEX-SOCKET-HEAD CAP SCREW |
| 164. | [1] | 026510-1340 | GASKET D13.4&10.2T1 |
| 190. | [1] | 158017-1000 | GASKET |
| 200. | [1] | 158599-6720 | SPARE PART |
Include in #2:
105856-2021
as INJECTION-PUMP ASSEMBLY
Cross reference number
Zexel num
Bosch num
Firm num
Name
Information:
(1) Torque for fuel injection line nut ... 40 7 N m (30 5 lb.ft.)(2) Torque for retainer ... 48 7 N m (35 5 lb.ft.)(3) Torque for bleed screw ... 2.2 0.8 N m (20 7 lb.in.) Always use a new washer (seal) anytime the bleed screw is loosened or removed.(4) Washer. Make sure the correct washer is used when the nozzle assembly is installed.(5) Put liquid soap on rubber O-ring and bore in head before assembly.(6) Put 5P3931 Anti-Seize Compound on the threads of the adapter before installation. Torque for the adapter ... 205 14 N m (150 10 lb.ft.)See Testing And Adjusting section, for fuel injection nozzle test procedure.Earlier Engines
(1) Nut for fuel line. Hold adapter assembly (2) when nut (1) is loosened or tightened. Torque for the nut ... 40 7 N m (30 5 lb.ft.)(2) Adapter assembly.(3) Torque for bleed screw ... 1.6 0.4 N m (14 4 lb.in.)Always use a new washer (seal) anytime the bleed screw is loosened or removed.(4) Washer. Make sure the correct washer is used when the nozzle assembly is installed. Check the Engine Arrangement for the correct part number to use.(5) Torque for clamp bolt ... 31 7 N m (23 5 lb.ft.)(6) Put liquid soap on rubber O-ring and bore in head before assembly.(7) Put 5P3931 Anti-Seize Compound on the threads of the adapter before installation. Torque for the adapter ... 205 14 N m (150 10 lb.ft.)Engines With Capsule-Type Nozzles
Earlier Engines
(1) Torque for
(1) Nut for fuel line. Hold adapter assembly (2) when nut (1) is loosened or tightened. Torque for the nut ... 40 7 N m (30 5 lb.ft.)(2) Adapter assembly.(3) Torque for bleed screw ... 1.6 0.4 N m (14 4 lb.in.)Always use a new washer (seal) anytime the bleed screw is loosened or removed.(4) Washer. Make sure the correct washer is used when the nozzle assembly is installed. Check the Engine Arrangement for the correct part number to use.(5) Torque for clamp bolt ... 31 7 N m (23 5 lb.ft.)(6) Put liquid soap on rubber O-ring and bore in head before assembly.(7) Put 5P3931 Anti-Seize Compound on the threads of the adapter before installation. Torque for the adapter ... 205 14 N m (150 10 lb.ft.)Engines With Capsule-Type Nozzles
Earlier Engines
(1) Torque for