Fuel injectors
  1. Home
  2. hydraulic
  3. #1058560521

105856-0521 ZEXEL F 019 Z2E 051 BOSCH HYDRAULIC GOVERNOR f019z2e051 1058560521


 

Information hydraulic governor

BOSCH F 019 Z2E 051 f019z2e051
ZEXEL 105856-0521 1058560521
105856-0521 HYDRAULIC GOVERNOR
Rating:
51
Buy HYDRAULIC GOVERNOR 105856-0521 zexel genuine, new aftermarket engine parts with delivery

Components :

0. INJECTION-PUMP ASSEMBLY 105856-0521
1. _
2. FUEL INJECTION PUMP
3. NUMBER PLATE
4. _
5. CAPSULE
6. ADJUSTING DEVICE
7. NOZZLE AND HOLDER ASSY
8. Nozzle and Holder
9. Open Pre:MPa(Kqf/cm2)
10. NOZZLE-HOLDER
11. NOZZLE

Scheme ###:

BASE
1. [1] 158502-0420 BASE
2. [1] 029811-8000 BEARING PLATE
3. [1] 158528-0900 PACKING RING
7. [1] 158131-0100 GEAR SHAFT
10. [1] 158028-0000 O-RING
11. [1] 158507-1820 DIAPHRAGM HOUSING
13. [1] 158621-0800 SLEEVE
18. [1] 158699-0321 COMPENSATOR ASSY
18/1. [1] 158610-0901 POWER PISTON
18/3. [1] 158654-0400 COILED SPRING
18/4. [1] 158614-0300 STOP PIN
18/5. [1] 158612-0500 PLAIN WASHER
18/6. [1] 158654-0500 COILED SPRING
18/7. [1] 016110-1220 LOCKING WASHER
18/8. [1] 158612-0001 BUSHING
18/9. [2] 158528-1300 O-RING
18/10. [1] 158615-0300 PUMP PLUNGER
18/11. [1] 025620-1410 SPRING PIN
35. [3] 029330-6070 GASKET
36. [3] 010206-2520 HEX-SOCKET-HEAD CAP SCREW
50. [1] 158600-0720 FLYWEIGHT ASSEMBLY
51. [1] 158106-0100 PLAIN WASHER
52. [1] 029811-0000 BEARING PLATE
53. [1] 158620-1220 PILOT VALVE
60. [2] 158220-0000 GUIDE LEVER
61. [2] 158736-0200 BEARING PIN
62. [4] 025520-1510 SPLIT PIN
70. [1] 158730-0220 TERMINAL ARM
70/1. [1] 158230-0020 TERMINAL ARM
70/2. [1] 158315-0200 TERMINAL SHAFT
70/3. [1] 158315-0200 TERMINAL SHAFT
70/4. [2] 158736-0100 TAPER PIN
70/5. [2] 011006-0620 SET OF NUTS
70/6. [1] 158214-0020 SPEED DROOP ADJUSTER
70/7. [1] 014020-5120 PLAIN WASHER
70/8. [1] 029320-5030 TAB WASHER
70/9. [1] 010535-1220 FLAT-HEAD SCREW
85. [1] 158814-0900 SPEED CONTROL SHAFT
86. [2] 158823-0300 BUSHING
86. [2] 158823-0300 BUSHING
87. [1] 158322-0200 COILED SPRING
88. [1] 158710-0400 STRAP
89. [1] 029404-5010 BEARING PIN
95. [1] 158211-0100 STRAP
96. [2] 158653-0100 WIRE
104. [1] 158017-0900 GASKET
105. [1] 158562-1820 HYDRAULIC N.CONT.
105/1. [1] 158562-4600 COVER
105/2. [1] 158910-0100 CYLINDER
105/3. [3] 029050-6090 FLAT-HEAD SCREW
105/5. [1] 158416-0000 FLAT-HEAD SCREW
105/6. [1] 158915-0700 UNION NUT
105/7. [1] 029301-0370 PLAIN WASHER
105/8. [1] 158412-0200 COILED SPRING K2.0
105/9. [1] 158912-0600 COILED SPRING K5.1
105/9B. [1] 158912-0500 COILED SPRING K4.9
105/9C. [1] 158912-0700 COILED SPRING K5.2
105/9D. [1] 158912-1100 COILED SPRING K4.8
105/9E. [1] 158912-1200 COILED SPRING K5.4
105/10. [1] 029301-0370 PLAIN WASHER
105/11. [1] 158913-0220 STOP PIN
105/12. [2] 158414-0000 PUMP PLUNGER
105/12. [2] 158414-0000 PUMP PLUNGER
105/13. [2] 158414-0100 DIAPHRAGM
105/13. [2] 158414-0100 DIAPHRAGM
105/14. [2] 158414-0200 PLATE
105/14. [2] 158414-0200 PLATE
105/15. [1] 010006-1440 BLEEDER SCREW M6P1L14 4T
105/16. [1] 026506-1040 GASKET D9.9&6.2T1
105/17. [1] 158911-0200 CYLINDER
105/18. [1] 158911-0400 BUSHING
105/19. [1] 158913-0100 RACK
105/20. [1] 158912-0800 COILED SPRING
105/21. [1] 026506-1040 GASKET D9.9&6.2T1
105/22. [1] 010006-1440 BLEEDER SCREW M6P1L14 4T
105/23. [4] 029010-6350 BLEEDER SCREW M6P1.0L22
105/24. [2] 014110-6440 LOCKING WASHER
105/25. [2] 158909-0300 FLAT-HEAD SCREW
105/26. [1] 027114-1040 INLET UNION
105/27. [2] 029331-4120 GASKET D18&14.2T1.5
105/28. [1] 027414-2640 EYE BOLT
105/29. [1] 158411-0100 FLANGE BUSHING
105/30. [1] 158911-0500 CONNECTOR
105/31. [1] 029100-6050 SET OF NUTS
105/32. [1] 013020-6040 UNION NUT M6P1H5
105/33. [2] 026506-1040 GASKET D9.9&6.2T1
105/34. [1] 154035-1600 CAP NUT
105/35. [4] 029050-6220 FLAT-HEAD SCREW
105/36. [1] 027114-1040 INLET UNION
105/37. [2] 029331-4120 GASKET D18&14.2T1.5
105/38. [1] 027414-2640 EYE BOLT
105/40. [1] 013020-6040 UNION NUT M6P1H5
105/41. [1] 158567-1200 SET OF NUTS
105/45. [1] 026512-1640 GASKET D15.9&12.2T1
105/46. [1] 158066-0000 BLEEDER SCREW
106. [4] 029010-6350 BLEEDER SCREW M6P1.0L22
118. [1] 158027-0100 NEEDLE VALVE
119. [1] 016500-0710 O-RING
123. [2] 026512-1640 GASKET D15.9&12.2T1
124. [2] 029111-2070 CAPSULE M12P1.5L10
130. [1] 029331-8040 GASKET
131. [1] 158660-0320 CONTROL VALVE
135. [1] 158515-0700 INDICATOR PLATE
137. [1] 158515-0800 INDICATOR PLATE
140. [1] 158820-0620 POINTER
142. [1] 158820-0620 POINTER
158. [1] 015040-0880 BEARING PIN
190. [1] 158017-1000 GASKET
200. [1] 158599-0920 SPARE PART

Include in #2:

105856-0521 as INJECTION-PUMP ASSEMBLY

Cross reference number

Zexel num
Bosch num
Firm num
Name
105856-0521 
105856-0522 
F 019 Z2E 051 
   
HYDRAULIC GOVERNOR
* K 35AA Hydraulic RHD6 Others




Information:

2. Remove the bolts (1) and water lines (2).3. Loosen the drive belts (4).4. Remove the bolts (3) that hold water pump to cylinder block.5. Remove the water pump.Install Water Pump
1. Put the water pump into position on engine, and install the bolts.2. Put the two water lines in position, and install the four bolts.3. Install the drive belts and tighten them to the tension given in OPERATION AND MAINTENANCE GUIDE.4. Fill the cooling system.Disassemble Water Pump
start by: a) remove water pump 1. Remove nut (1) and lock from shaft. Remove the pulley (2) from shaft.2. Remove bolts (3) from housings, and pull the housings (4) and (5) apart.3. Remove the lip-type seal from housing (4).4. Remove the ring for seal from pulley (2). 5. Lift the shaft (6) out of housing (5). 6. Remove cotter pin, nut (10), and washer. Remove the impeller (8).7. Remove bolts (7) and locks, and remove the housing (9) from shaft. 8. Remove seals (11) and (12) from housing (9).9. Remove the key, two bearings, spacer, and plate from shaft (6).Assemble Water Pump
1. Use tool setup (A) to install the seal in housing (1) with lip of seal toward impeller side of housing. Put oil on lip of seal. 2. Heat the bearings (3) and (6) in oil at a maximum temperature of 275°F (135°C).3. Install bearing (3), plate (4), spacer (5), bearing (6), and key (7) on shaft (2).4. Put housing (1) in position on shaft (2). Install the four bolts (10) and two locks.5. Install the seal and ring in housing (1) with the shiny surface of ring toward impeller. 6. Put the seal assembly in position on shaft, and install the impeller (9). Install washer and nut (8). Tighten the nut to 30 5 lb.ft. (4.1 0.7 mkg) plus amount needed to install the cotter pin.7. Put the shaft, housing, and impeller in position in housing (11). 8. Use tool setup (B) to install seal in housing (13) with lip of seal toward pulley. Install the ring for seal on pulley (15). Put oil on lip of seal.9. Put housing (13) in position, and install the bolts (12). Install pulley (15), lock, and nut (14). Tighten nut to 55 lb.ft. (7.6 mkg) and bend the lock.end by: a) install water pump

Have questions with 105856-0521?





Group cross 105856-0521 ZEXEL

Fuji-Diesel 

105856-0511  
F 019 Z2E 050 
RHD6-MC 
A33062 
HYDRAULIC GOVERNOR
105856-0511  
F 019 Z2E 050 
RHD6-MC 
A36311 
HYDRAULIC GOVERNOR
105856-0521  

105856-0522 
F 019 Z2E 051 
 
HYDRAULIC GOVERNOR
105856-0522  
F 01G 29N 01V 
RHD6-PHC 
 
HYDRAULIC GOVERNOR
105856-0530  
 
 

105856-0540  
 
 

105856-0550  
 
 

105856-0560  
 
 

105856-0570  

105856-7023 
 
17720008A 
HYDRAULIC GOVERNOR
105856-0580  
 
 

Niigata-Urawa 

105856-0590  

105856-0970 
F 019 Z2E 052 
74044102C 
HYDRAULIC GOVERNOR
105856-0590  

105856-0970 
F 019 Z2E 052 
74044102B 
HYDRAULIC GOVERNOR
Back to top