Fuel injectors
  1. Home
  2. governor
  3. #1059323690

105932-3690 ZEXEL F 019 Z2E 981 BOSCH GOVERNOR f019z2e981 1059323690


 

Information governor

BOSCH F 019 Z2E 981 f019z2e981
ZEXEL 105932-3690 1059323690
105932-3690 GOVERNOR
Rating:
24
Buy GOVERNOR 105932-3690 zexel genuine, new aftermarket engine parts with delivery

Scheme ###:

GOVERNOR HOUSING
1. [1] 159200-7220 GOVERNOR HOUSING
2. [1] 154007-0200 ADAPTOR
3. [1] 020018-1840 BLEEDER SCREW M8P1.25L18
4. [1] 159232-2620 PLATE
5. [5] 029010-6810 BLEEDER SCREW
5B. [1] 020106-1640 BLEEDER SCREW M6P1.0L14
7. [1] 139710-0200 O-RING
8. [1] 159205-2321 LEVER SHAFT
9. [1] 159202-7800 CONTROL LEVER
10. [1] 016010-0810 LOCKING WASHER
11/1. [0] 029311-0220 SHIM D18&10.3T0.2
11/1. [0] 029311-0230 SHIM D18&10.3T0.5
11/1. [0] 029311-0430 SHIM D18&10.3T0.30
11/1. [0] 029311-0440 SHIM D18&10.3T0.40
11/1. [0] 029311-0450 SHIM D18&10.3T0.25
11/1. [0] 029311-0460 SHIM D18&10.3T0.35
11/1. [0] 139410-3300 SHIM D18&10.3T0.6
11/1. [0] 139410-3400 SHIM D18&10.3T0.8
11/1. [0] 139410-3500 SHIM D18&10.3T0.9
12. [1] 159215-0000 COILED SPRING
13. [1] 159242-6601 CONTROL LEVER
15. [1] 013020-8040 UNION NUT M8P1.25H7
16. [1] 159237-5500 CAPSULE
17. [1] 159202-5320 CONTROL LEVER
18. [1] 159215-0300 COILED SPRING
20. [1] 159242-0220 CONTROL LEVER
21. [1] 029311-0210 SHIM D14&10.1T1
22. [1] 139610-0700 PACKING RING
23/1. [0] 139410-3800 SHIM D22&10.2T0.2
23/1. [0] 139410-3900 SHIM D22&10.2T0.3
23/1. [0] 139410-4000 SHIM D22&10.2T0.4
23/1. [0] 139410-4100 SHIM D22&10.2T0.6
23/1. [0] 139410-4200 SHIM D22&10.2T0.8
24. [1] 159215-7200 COILED SPRING
25. [1] 159235-6500 CAP
26. [1] 159290-8020 CONTROL LEVER
27. [1] 020006-1640 BLEEDER SCREW M6P1L16 4T
35. [1] 159255-4920 GOVERNOR COVER
35/1. [1] 159301-8020 GOVERNOR COVER
35/1/1. [1] 159301-7920 GOVERNOR COVER
35/1/1/4. [1] 159230-2800 BUSHING
35/1/2. [1] 159252-4420 LEVER GROUP
35/1/2/1. [1] 159202-2200 CONTROL LEVER
35/1/2/2. [1] 016010-0810 LOCKING WASHER
35/1/2/3. [1] 159202-2120 CONTROL LEVER
35/1/2/4. [1] 016010-0810 LOCKING WASHER
35/1/2/5. [1] 159215-2301 COILED SPRING
35/1/2/6. [1] 159205-6320 LEVER SHAFT
35/1/3. [1] 139411-0600 SHIM
35/1/4. [1] 159238-3000 LOCKING WASHER
35/1/5. [1] 139610-0600 PACKING RING
35/2. [1] 159205-0400 LEVER SHAFT
35/3. [2] 159237-0200 CAPSULE
35/3. [2] 159237-0200 CAPSULE
35/4. [1] 159253-2320 TENSIONING LEVER
35/4/2. [1] 159204-5021 RACK
35/4/3. [1] 159233-0300 UNION NUT
35/4/4. [1] 159234-0300 FLAT-HEAD SCREW
35/4/5. [1] 159216-0000 COILED SPRING
35/4/6. [1] 159216-0100 COILED SPRING
35/5. [1] 159203-7020 GUIDE LEVER
35/6. [2] 159235-5000 BUSHING
35/7. [1] 159215-1701 COILED SPRING
35/8. [1] 159231-1300 BEARING PIN
35/9. [2] 016010-0610 LOCKING WASHER
35/10. [1] 159238-2900 BUSHING
51. [7] 020106-3840 BLEEDER SCREW
65. [1] 154612-4621 RACK SENSOR ASSY
65/1. [1] 407945-0281 RACK SENSOR
65/2. [1] 154390-4000 GASKET
65/3. [2] 020106-1670 BLEEDER SCREW
100. [1] 154100-9520 FLYWEIGHT ASSEMBLY
101. [1] 025803-1610 WOODRUFF KEY
102. [1] 029321-2020 LOCKING WASHER
103. [1] 029231-2030 UNION NUT
110. [1] 154123-2320 SLIDING PIECE
111/1. [0] 029311-0010 SHIM D14&10.1T0.2
111/1. [0] 029311-0180 SHIM D14&10.1T0.3
111/1. [0] 029311-0190 SHIM D14&10.1T0.40
111/1. [0] 029311-0210 SHIM D14&10.1T1
111/1. [0] 139410-0000 SHIM D14.0&10.1T0.5
111/1. [0] 139410-0100 SHIM D14.0&10.1T1.5
111/1. [0] 139410-3000 SHIM D14&10.1T2.0
111/1. [0] 139410-3100 SHIM D14&10.1T3.0
111/1. [0] 139410-3200 SHIM D14&10.1T4.0
112. [1] 159236-0200 TERMINAL STUD
130. [1] 159217-1100 GOVERNOR SPRING
131. [1] 159211-3400 GOVERNOR SPRING
132. [1] 159214-0000 COILED SPRING
133. [1] 159219-4920 SPRING PACK
133/1. [1] 159234-5602 GUIDE SLEEVE
133/2. [1] 159212-3300 COILED SPRING
133/3. [1] 159219-1400 COILED SPRING
133/4/1. [0] 029310-9240 SHIM D11.9&9T0.1
133/4/1. [0] 029310-9250 SHIM D11.9&9T0.2
133/4/1. [0] 029310-9260 SHIM D11.9&9T0.25
133/4/1. [0] 029310-9270 SHIM D11.9&9T1.0
133/4/1. [0] 139409-0100 SHIM D11.9&9T0.3
133/4/1. [0] 139409-0200 SHIM D11.9&9T0.5
133/4/1. [0] 139409-0300 SHIM D11.5&9T0.8
135. [1] 159248-2700 FLAT-HEAD SCREW
137. [1] 159237-5300 CAPSULE
140. [1] 159205-2101 LEVER SHAFT
145. [1] 159233-5700 UNION NUT
149. [1] 159237-5400 CAPSULE
150. [1] 159235-5300 SLOTTED WASHER
155. [1] 159204-7720 STRAP
156. [1] 159233-0520 BLEEDER SCREW
158. [1] 013020-5240 UNION NUT M5P0.8H4
170. [1] 159295-1421 CONTROL LEVER
171. [1] 014110-8440 LOCKING WASHER
172. [1] 013020-8040 UNION NUT M8P1.25H7
173/1. [1] 139006-7700 BLEEDER SCREW
173/1. [1] 139006-7800 BLEEDER SCREW
173/1. [1] 139006-7900 BLEEDER SCREW
173/1. [1] 139006-8000 BLEEDER SCREW
173/1. [1] 139006-8100 BLEEDER SCREW
173/1. [1] 139006-8200 BLEEDER SCREW
173/1. [1] 139006-8300 BLEEDER SCREW
174. [1] 154012-5500 BLEEDER SCREW
175. [1] 154012-5300 FLAT-HEAD SCREW M8P1.25L55
176. [1] 159233-7500 UNION NUT
177. [1] 154011-2300 UNION NUT
178. [1] 013020-8040 UNION NUT M8P1.25H7
236. [1] 154390-1300 GASKET
237. [1] 159238-3100 GASKET
250. [1] 159228-4920 BRACKET
251. [2] 154332-9900 COILED SPRING
252. [1] 159248-0200 BLEEDER SCREW
257. [2] 154156-0600 TUBE
300. [1] 159310-2800 CAM PLATE
301. [1] 016010-0840 LOCKING WASHER
303. [1] 016010-0540 LOCKING WASHER
311. [1] 159237-0200 CAPSULE
835S. [1] 154062-1900 CAP D12L24
836S. [1] 154062-1700 CAP D20L32

Include in #1:

101606-0300 as GOVERNOR

Cross reference number

Zexel num
Bosch num
Firm num
Name
105932-3690 
F 019 Z2E 981 
NP-EP/RLD280-1450A1FFL 
   
GOVERNOR
K 14JK MECHANICAL GOVERNOR GOV RLD GOV




Information:

Installation procedure
Installation: Oil pan* Clean the sealant application surfaces of each part. * Apply a bead of sealant to each of the mating surfaces of the timing gear case, lower crankcase and front plate (at the two locations indicated the illustration). Installation: Oil pan* Clean the mating surfaces of each part. * Apply a bead of sealant to the mating surface of the oil pan evenly and without any breaks.* Mount the oil pan within three minutes of applying the sealant. Make sure that the sealant stays in place.
* Do not start the engine less than an hour after installation. If the oil pan mounting bolts were loosened or removed, be sure to reapply sealant.
Oil Pump
* Disassembly sequence1 Oil pump cover2 Driven gear3 Plug4 Relief valve spring5 Steel ball6 Gear and case7 O-ring*a Drive gear*b Oil pump gearP Locating pinX Non-reusable parts* Assembly sequenceFollow the disassembly procedure in reverse.Service standards (Unit: mm) Tightening torque (Unit: N m {kgf m}) Lubricant and/or sealant Inspection procedure
Inspection: Oil pump cover, driven gear, and gear and case* Measure the clearance between each gear's shaft and the oil pump cover, as well as between each gear's shaft and the gear and case. * If the measurements are not within the standard value range, replace the defective part(s). Inspection: Driven gear, drive gear and gear and case* Carry out the following inspection. Replace the oil pump if any defects are found. (1) Sinkage of each gear from gear and case end surface(2) Gear and case-to-tooth tip clearance for each gear Oil Cooler <Engine-Mounted Type, Engine Separately Mounted Type>, and Oil Filter <Engine-Mounted Type>
* Wipe up any spilled engine oil, as it can cause fires.* To avoid any risks of burns, take care not to touch the engine oil when the engine is hot.
* Make sure not to put any engine oil on the belt when working on the oil cooler and oil filter. Belt soiled with oil or grease may easily slip, resulting in deteriorated performance of the cooling system.* Do not reuse the oil filter elements by washing.
* Removal sequence1 Oil filter2 Plug3 Regulator valve spring4 Regulator valve5 Plug6 Bypass valve spring7 Bypass valve8 Oil cooler element9 Gasket10 Water drain plug11 Oil cooler body12 O-ring13 Gasket14 Water separate lipX Non-reusable parts* Installation sequenceFollow the removal sequence in reverse.Service standards (Unit: mm) Tightening torque (Unit: N m {kgf m}) Lubricant and/or sealant Special tools Removal procedure
Removal: Oil filter <Engine-mounted type> Inspection procedure
Inspection: Oil cooler element* Plug the outlet of the oil cooler element and connect a hose to the engine oil inlet port. Then, immerse the oil cooler element in a tank of water. * Apply an air pressure of 1.5 MPa {15 kgf/cm2} for 15 seconds through the hose, and check for any air leaks.* Replace the element if it leaks air.Installation procedure
Installation: Oil cooler <Engine-mounted type>* Clean the oil filter mounting surface of the oil cooler. * Apply a thin coat of engine oil on the oil filter gasket.* Screw in the

Have questions with 105932-3690?





Group cross 105932-3690 ZEXEL

Nissan-Diesel 

105932-3600  
F 019 Z2E 827 
NP-EP/RLD275-1300A1CFL 
19101Z9002 
GOVERNOR

Isuzu 

105932-3610  
F 019 Z5E 898 
NP-EP/RLD275-1750A2FBL 
8972634690 
GOVERNOR

Mitsubishi 

105932-3620  
F 019 Z2E 031 
NP-EP/RLD275-1550A1FBL 
ME755445 
GOVERNOR
105932-3630  
F 019 Z1E 937 
NP-EP/RLD275-1550A1FBL 
ME755446 
GOVERNOR

Isuzu 

105932-3640  
F 019 Z2E 562 
NP-EP/RLD315-1500A2FYL 
8973116000 
GOVERNOR
105932-3650  
F 019 Z2E 977 
NP-EP/RLD275-1500A1FFL 
1157901260 
GOVERNOR
105932-3660  
F 019 Z2E 978 
NP-EP/RLD275-1500A1FFL 
1157901290 
GOVERNOR
105932-3670  
F 019 Z2E 979 
NP-EP/RLD275-1500A1FFL 
1157901300 
GOVERNOR
105932-3680  
F 019 Z2E 980 
NP-EP/RLD275-1500A1FFL 
1157901310 
GOVERNOR
105932-3690  
F 019 Z2E 981 
NP-EP/RLD280-1450A1FFL 
 
GOVERNOR
Back to top