105931-8950 ZEXEL GOVERNOR Cross 1059318950 8970452100


 

Information governor

ZEXEL 105931-8950 1059318950
ISUZU 8970452100 8970452100
105931-8950 GOVERNOR
Rating:
13
Buy GOVERNOR 105931-8950 zexel genuine, new aftermarket engine parts with delivery

Cross reference number

Zexel num
Bosch num
Firm num
Name
105931-8950 
105931-8951 
 
8970452100  ISUZU
GOVERNOR
* K 14JK GOV RLD GOV




Information:


Repeat Steps 4 through 6 to remove (bleed) air from the rear table lift cylinder (not shown).
Open (CCW) hand pump control knob (11) to completely lower the DPF cleaner table. Close (CW) the hand pump control knob.
Illustration 38 g02728258
(28) Hydraulic Oil Level 51 to 102 mm (2.0 to 4.0 inch)
Check the oil level in the pump reservoir. Remove fill cap (13) located on the end cap of the hand pump. Hydraulic oil level (28) should be 51 to 102 mm (2.0 to 4.0 inch) from the bottom of the fill hole. Add high-grade hydraulic oil, if needed.Note: A clean wire tie can be used as a dipstick to measure the hydraulic oil level in the pump reservoir.Troubleshooting Guide
Table 3
Symptom     Solution    
Air dryer desiccant is a pinkish color.     1. Replace or regenerate the desiccant. Refer to ""Maintenance Section"".    
Bursting does not occur.     1. Check display screen for error message.
2. Check power connection to burst valve solenoid.    
Cabinet doors do not close correctly.     1. Look for damaged door hinges, seals, and latches.
2. Verify that vehicle sensors have been removed from DPF.    
Cabinet doors open during burst process.     1. Verify that doors are correctly latched.
2. Look for damage to door latches.
3. Check seals between DPF and adapters.    
Clamping force cannot be obtained.     1. Look for hydraulic fluid leaks.
2. Check fluid level in hydraulic pump. Refer to ""Maintenance Section"".    
Clamping force does not hold.     1. Upon initial clamping, it is possible for clamp load to drop
689 to 1379 kPa (99.9 to 200.0 psi) within the first minute, due to temperature effects. After reclamping, the drop should be virtually zero.
2. Look for hydraulic fluid leaks.    
Display screen is blank.     1. Verify that machine is ON, plugged into an outlet, and power is available to the outlet.
2. Reset circuit breakers located on left side of control cabinet.    
DPF does not line up correctly on the table.     1. Verify that correct adapters are being used.
2. Verify DPF is correctly seated on to lower adapter.    
DPF is damaged after cleaning process.     1. Check DPFs for damage before cleaning.
2. Look for damage on adapters.
3. Verify that correct cleaning protocol was entered into machine.    
DPF is not cleaned.     1. Check orientation of DPF. Refer to ""General Information"" Section.
2. Verify that correct cleaning protocol was entered into machine.
3. Look for other DPF conditions that may prevent successful cleaning.  

Have questions with 105931-8950?





Group cross 105931-8950 ZEXEL

Isuzu 

F 019 Z5E 800 
NP-EP/RLD260-1500A1FFL 
1157706020 
GOVERNOR
F 019 Z5E 801 
NP-EP/RLD260-1500A1FFL 
1157706030 
GOVERNOR
 
1157706040 
GOVERNOR
9 420 613 062 
NP-EP/RLD260-1500A1FBL 
1157706041 
GOVERNOR
F 019 Z5E 802 
NP-EP/RLD260-1500A1FFL 
1157706050 
GOVERNOR
 
1157706060 
GOVERNOR
F 019 Z5E 803 
NP-EP/RLD260-1500A1FBL 
1157706061 
GOVERNOR
105931-8950  

105931-8951 
 
8970452100 
GOVERNOR
9 420 613 929 
NP-EP/RLD300-1750A2FFL 
8970452101 
GOVERNOR
9 420 613 063 
 
GOVERNOR

Isuzu 

9 420 613 064 
8970645710 
GOVERNOR
F 019 Z5E 804 
NP-EP/RLD275-1645A1FBL 
8970645711 
GOVERNOR
 
 
GOVERNOR

Isuzu 

9 420 613 065 
8970645720 
GOVERNOR
9 420 613 066 
NP-EP/RLD275-1500A1FBL 
8970645722 
GOVERNOR
 
1157705900 
GOVERNOR
9 420 613 067 
NP-EP/RLD260-1600A1CFL 
1157705901 
GOVERNOR

Mitsubishi 

F 019 Z5E 805 
NP-EP/RLD275-1550A1FFL 
ME730752 
GOVERNOR
Back to top