105931-4210 ZEXEL GOVERNOR Cross 1059314210 8944697110


 

Information governor

ZEXEL 105931-4210 1059314210
ISUZU 8944697110 8944697110
105931-4210 GOVERNOR
Rating:
30
Buy GOVERNOR 105931-4210 zexel genuine, new aftermarket engine parts with delivery

Cross reference number

Zexel num
Bosch num
Firm num
Name
105931-4210 
105931-4211 
 
8944697110  ISUZU
GOVERNOR
*




Information:

1. Remove line (1) from the fuel ratio control. Remove two bolts (3), and remove solenoid (2) from the governor housing.2. Disconnect throttle linkage (4) from the lever assembly on the side of the governor housing. (A test application is shown in the photo.)3. Remove two bolts (5) from the front of the governor housing. Remove eight bolts (6), and remove governor housing (7). 4. Remove two bolts that hold fuel ratio control (8) to the governor housing. Unscrew the fuel ratio control from shaft (9) and remove it.5. Remove plug and seal (10) from the governor housing. 6. Remove two bolts (12) that hold lock (11) and flange (14) on fuel ratio control (8). Remove lock (11), flange (14), and O-ring seal (13) from the fuel ratio control.7. Check the condition of O-ring seal (13). If it is worn or damaged, make a replacement with a new part. 8. Remove ring (19) from the end of shaft (15). Remove lever assembly (18), spring (17), lever (16), spacer (21) and shaft (15) from the governor housing.9. Remove pin (20) from lever assembly (18) with a hammer and punch. Remove shaft (9) from the lever assembly. The following steps are for the installation of the fuel ratio control.10. Position shaft (9) in lever assembly (18) and install it with pin (20) using a hammer and punch.11. Install shaft (15), spacer (21), lever (16), spring (17) and lever assembly (18) in the governor housing. Install ring (19) on the end of shaft (15).12. Install O-ring seal (13) on fuel ratio control (8). Install flange (14) and lock (11) on the fuel ratio control with bolts (12).13. Install seal and plug (10) in the governor housing.14. Check the condition of the four O-ring seals on top of the governor housing where the fuel ratio control mounts. If any of the seals are worn or damaged, make a replacement with new parts.15. Screw fuel ratio control (8) onto shaft (9) approximately six turns. Install the fuel ratio control with the two bolts that hold it to the governor housing.16. Position governor housing (7), and install two bolts (5) on the front of the governor housing. Install eight bolts (6).17. Connect throttle linkage (4) to the lever assembly on the side of the governor housing.18. Install solenoid (2) with bolts (3). Install line (1) on the fuel ratio control.19. Make an adjustment to the fuel ratio control. See the topic, FUEL RATIO CONTROL ADJUSTMENT in the TESTING AND ADJUSTING section of this Module.

Have questions with 105931-4210?





Group cross 105931-4210 ZEXEL

Mitsubishi 

F 019 Z1E 490 
NP-EP/RLD275-1550A1AFL 
ME722735 
GOVERNOR

Isuzu 

105931-4210  

105931-4211 
 
8944697110 
GOVERNOR
 
 
GOVERNOR
 
 

 
 

 
 

Isuzu 

 
1157209740 
GOVERNOR
 
1157209840 
GOVERNOR
 
 
GOVERNOR
 
 
GOVERNOR

Isuzu 

F 019 Z1E 241 
NP-EP/RLD300-1850A2EKL 
8944677112 
GOVERNOR

Nissan-Diesel 

9 420 610 051 
NP-EP/RLD360-2000A2EXL 
19200C8704 
GOVERNOR

Isuzu 

 
1157705040 
GOVERNOR
Back to top