105923-1551 ZEXEL GOVERNOR Cross 1059231551 1157708400


 

Information governor

ZEXEL 105923-1551 1059231551
ISUZU 1157708400 1157708400
105923-1551 GOVERNOR
Rating:
24
Buy GOVERNOR 105923-1551 zexel genuine, new aftermarket engine parts with delivery

Cross reference number

Zexel num
Bosch num
Firm num
Name
105923-1551 
105923-1552 
 
1157708400  ISUZU
GOVERNOR
* K




Information:


Do not bend or add stress the shaft when the nut is loosened or tightened.
d. Loosen the nut on the shaft.e. Tighten nut to ... 3.5 N m (30 lb in)f. Tighten the nut an additional ... 120°g. Remove the nut from the shaft.h. Use 6V1541 Quick Cure Primer on the threads of the shaft and nut.i. Put 9S3265 Retaining Compound on the threads of the shaft and nut.j. Again tighten the nut to ... 3.5 N m (30 lb in)k. Again tighten the nut and additional ... 120°(2) Torque for the bolts that hold back plate ... 10 1 N m (90 10 lb in)(3) Torque for the clamp bolts ... 14 1 N m (120 10 lb in)(4) Bore in the bearings ... 15.921 to 15.931 mm (.6268 to .6272 in) Diameter of the surface on the shaft for the bearings ... 15.875 to 15.885 mm (.6250 to .6254 in)(5) Bore in the housing ... 24.961 to 24.973 mm (.9827 to .9832 in) Outside diameter of the bearing ... 24.846 to 24.859 mm (.9782 to .9787 in)(6) Clearance between the ends of the oil seal ring ... 0.20 to 0.38 mm (.008 to .015 in)(7) End play for the shaft ... 0.08 to 0.25 mm (.003 to .010 in)(8) Put 5P3931 Anti-Seize Compound on the threads and tighten the bolts that hold the turbocharger to the manifold to a torque of ... 54 5 N m (40 4 lb ft)Turbocharger S4A
(1) End play for shaft (new) ... 0.114 0.038 mm (.0045 .0015 in) Maximum permissible end play (worn) ... 0.20 mm (.008 in)(2) Thickness of thrust bearing (where thrust rings contact bearing) ... 5.36 0.03 mm (.211 .001 in)(3) Tighten both band clamps with procedure that follows: a. Tighten to ... 14 1.1 N m (125 10 lb in)b. Tap (hit) clamp lightly all around.c. Tighten again to ... 14 1.1 N m (125 10 lb in)
Do not overtighten the clamps.
(4) Diameter of shaft (new) ... 15.997 to 16.005 mm (.6298 to .6301 in) Bore in the bearing (new) ... 16.035 to 16.043 mm (.6313 to .6316 in)Maximum permissible clearance between bearing and shaft (worn) ... 0.05 mm (.002 in)(5) Maximum permissible gap of oil seal ring, measured in bore of housing ... 0.25 mm (.010 in)(6) Install the compressor wheel (at room temperature) as follows: a. See Compressor Wheel Clearance for the correct shim thickness to use.b. Put compressor wheel on the shaft.c. Put a small amount of clean engine oil on the threads.d. Tighten the nut to a

Have questions with 105923-1551?





Group cross 105923-1551 ZEXEL

Mitsubishi 

 
ME740088 
GOVERNOR
 
ME740579 
GOVERNOR
 
ME740827 
GOVERNOR
9 420 611 027 
ME741587 
GOVERNOR
9 420 611 497 
ME741644 
GOVERNOR
F 019 Z5E 563 
NP-EP/RLD225-1200P6JFR 
ME742662 
GOVERNOR

Hino 

9 420 610 946 
223008480A 
GOVERNOR
9 420 610 668 
223008481A 
GOVERNOR
F 01G 29N 03W 
NP-EP/RLD225-1150T6LFR 
 
GOVERNOR

Mitsubishi 

F 019 Z5E 564 
NP-EP/RLD225-1200T6JFR 
ME740070 
GOVERNOR
F 019 Z5E 565 
NP-EP/RLD225-1200T6JFR 
ME740071 
GOVERNOR
 
 
GOVERNOR

Isuzu 

105923-1551  

105923-1552 
 
1157708400 
GOVERNOR
9 420 611 266 
NP-EP/RLD225-1250P6JFR 
1157708401 
GOVERNOR

Mitsubishi 

9 420 611 628 
ME740091 
GOVERNOR
9 420 611 028 
ME740580 
GOVERNOR
 
ME740820 
GOVERNOR
9 420 611 460 
NP-EP/RLD225-1200T6JFR 
ME740861 
GOVERNOR
 
ME740089 
GOVERNOR
9 420 610 442 
ME740581 
GOVERNOR
9 420 611 029 
ME741768 
GOVERNOR
F 019 Z5E 566 
NP-EP/RLD225-1250T6JFR 
ME742663 
GOVERNOR
 
ME740090 
GOVERNOR
F 019 Z5E 567 
NP-EP/RLD225-1250T6JFR 
ME740582 
GOVERNOR
 
 
GOVERNOR
9 420 610 669 
 
GOVERNOR
 
 
GOVERNOR
Back to top