105923-1540 ZEXEL F 019 Z5E 565 BOSCH GOVERNOR f019z5e565 1059231540 me740071


 

Information governor

BOSCH F 019 Z5E 565 f019z5e565
ZEXEL 105923-1540 1059231540
MITSUBISHI ME740071 me740071
105923-1540 GOVERNOR
Rating:
22
Buy GOVERNOR 105923-1540 zexel genuine, new aftermarket engine parts with delivery

Cross reference number

Zexel num
Bosch num
Firm num
Name
105923-1540 
F 019 Z5E 565 
NP-EP/RLD225-1200T6JFR 
ME740071  MITSUBISHI
GOVERNOR
K




Information:


Always use a wrench to hold the hex fitting on top of the master nozzle, when assembling or disassembling lines. If a wrench is not used, the master nozzle and manifold it is installed into may be damaged.
Check fuel line for "Close-in" Do NOT use fuel lines with an ID (inside diameter) LESS than 1.191 mm (0.0469 in). The fuel line ID can be checked using a 1.2 mm (.047 in) drill.If the drill bit can NOT be inserted into the fuel line high pressure hole, either drill out the line using a 1.6 mm (.063 in) drill or replace the fuel line with a new line. Use the same length and internal diameter lines each time the reference pump is tested.
If the fuel lines are not completely and thoroughly cleaned out after the drilling procedure, metal particles or foreign debris in the line will damage the master nozzles and contaminate the calibration fluid in the test stand.
After the hole has been drilled to the correct size, clean the line with solvent and remove any metal particles. Blow compressed air through the lines, after cleaning, to remove any solvent.
When using pressure air, wear a protective face shield and protective clothing. The maximum air pressure at the nozzle must be less than 205 kPa (30 psi) for cleaning purposes.
9. Identify fuel lines and nozzles in the same order as the reference pump plunger and barrels (1-6 or 1-12) and use the same lines and nozzles each time the reference pump is run on the test bench.10. Select two test points (speeds and shot settings) that will cover the delivery range realized in a dealer's shop.Always set up the test points using only the pump rack zero pin. Do not set the rack full load or idle stops.11. The test stand and reference pump should be run for ten minutes.Make sure test stand pressures and temperatures are within published specifications and that they are stable.12. Set the first test point.Take five samples (draws) and record the individual pump and barrel deliveries for each sample (draw).13. Examine pump and barrel sample data:* Are the samples consistent?The MAXIMUM allowable difference between the HIGH and LOW delivery pump and barrel in the reference pump should be three cc's.If there is NOT a three cc difference, swap pump and barrels in the pump housing (or check master nozzles for damage) and re-test UNTIL the maximum HIGH to LOW

Have questions with 105923-1540?





Group cross 105923-1540 ZEXEL

Mitsubishi 

 
ME740088 
GOVERNOR
 
ME740579 
GOVERNOR
 
ME740827 
GOVERNOR
9 420 611 027 
ME741587 
GOVERNOR
9 420 611 497 
ME741644 
GOVERNOR
F 019 Z5E 563 
NP-EP/RLD225-1200P6JFR 
ME742662 
GOVERNOR

Hino 

9 420 610 946 
223008480A 
GOVERNOR
9 420 610 668 
223008481A 
GOVERNOR
F 01G 29N 03W 
NP-EP/RLD225-1150T6LFR 
 
GOVERNOR

Mitsubishi 

F 019 Z5E 564 
NP-EP/RLD225-1200T6JFR 
ME740070 
GOVERNOR
105923-1540  
F 019 Z5E 565 
NP-EP/RLD225-1200T6JFR 
ME740071 
GOVERNOR
 
 
GOVERNOR

Isuzu 

 
1157708400 
GOVERNOR
9 420 611 266 
NP-EP/RLD225-1250P6JFR 
1157708401 
GOVERNOR

Mitsubishi 

9 420 611 628 
ME740091 
GOVERNOR
9 420 611 028 
ME740580 
GOVERNOR
 
ME740820 
GOVERNOR
9 420 611 460 
NP-EP/RLD225-1200T6JFR 
ME740861 
GOVERNOR
 
ME740089 
GOVERNOR
9 420 610 442 
ME740581 
GOVERNOR
9 420 611 029 
ME741768 
GOVERNOR
F 019 Z5E 566 
NP-EP/RLD225-1250T6JFR 
ME742663 
GOVERNOR
 
ME740090 
GOVERNOR
F 019 Z5E 567 
NP-EP/RLD225-1250T6JFR 
ME740582 
GOVERNOR
 
 
GOVERNOR
9 420 610 669 
 
GOVERNOR
 
 
GOVERNOR
Back to top