105921-0750 ZEXEL GOVERNOR Cross 1059210750 me717220


 

Information governor

ZEXEL 105921-0750 1059210750
MITSUBISHI ME717220 me717220
105921-0750 GOVERNOR
Rating:
72
Buy GOVERNOR 105921-0750 zexel genuine, new aftermarket engine parts with delivery

Cross reference number

Zexel num
Bosch num
Firm num
Name
105921-0750 
105921-0752 
 
ME717220  MITSUBISHI
GOVERNOR
*




Information:

Test Points (Voltages And Waveforms)
dc Voltages Conditions: 1. dc input voltage applied to POWER connector as shown.2. CALIBRATION CHECK/OPERATE switch in the OPERATE position.3. Neither transducer connected to indicator.4. TPI is reference for all voltages.Equipment Required: 6V3030 Digital Multimeterdc Input Voltages Waveforms Conditions: 1. dc power input voltage of 25 1 Volts.2. CALIBRATION CHECK/OPERATE switch in the CHECK position (can be held in CHECK position with tape).3. Neither transducer connected to indicator.4. TPI is reference for all waveforms.Equipment Required: dc oscilloscope (dual channel preferred). Waveform Time Relationships
VOLTAGES MAY VARY 10%, PULSE DURATIONS BY 20% EXCEPT 2.66 ms WHICH IS BASED ON A 12.000 kHz OSCILLATOR FREQ. (1C202). SIGNAL SOURCE IS INTERNAL CALIBRATOR. ALL TEST POINTS REFERENCED TO TP1.Waveform Time Relationships (enlarged scale)
VOLTAGES MAY VARY 10%, PULSE DURATIONS BY 20% EXCEPT 83.3 ?s AND 2.66 ms WHICH ARE EXACT BASED ON A 12.000 kHZ OSCILLATOR. (1C202) SIGNAL SOURCE IS INTERNAL CALIBRATOR. ALL TEST POINTS REFERENCED TO TP1.Disassembly Procedure
1 Remove six screws (1) from front panel (2), and remove panel (2) from case (3). Remove four screws (4) from the PC board, and also remove the locknuts from the two front panel switches (5) and (6). Carefully lift front panel (2) from PC (printed circuit) board (7).Calibration Procedure
To make sure the 6V3100 Timing Indicator Group (1) has good accuracy, check its calibration at a minimum of every six months. Also, the timing indicator will need calibration if: A. It does not show 2000 30 R/MIN at (A) and 32.0 .2 DEG at (B), when the CALIBRATION CHECK-OPERATE Switch (C) is in the CALIBRATION CHECK position. With no input signal at (D) or (E), the reading at R/MIN location (A) must show three zeros (000). If four zeros (0000) show, it is an indication of a possible need for calibration of the unit. This error only is not reason enough to do a complete calibration procedure. It is also not necessary to do a complete calibration procedure if the reading at the DEG location (B) has a decimal point as shown, (00.0) in addition to the three zeros.B. Reading is different than (000) at either location (A) or (B).All calibrations can be done with the use of a small screwdriver, a frequency counter and

Have questions with 105921-0750?





Group cross 105921-0750 ZEXEL

Mazda 

F 019 Z1E 691 
SL0313VL0 
GOVERNOR
 
SL0713VL0 
GOVERNOR
9 420 610 010 
SL0913VL0 
GOVERNOR
 
SL1113VL0 
GOVERNOR
 
SL1913VL0 
GOVERNOR

Mitsubishi 

105921-0750  

105921-0752 
 
ME717220 
GOVERNOR
 
ME723400 
GOVERNOR
F 019 Z5E 279 
NP-EP/RLD325-1750A2AXR 
ME726518 
GOVERNOR

Nissan-Diesel 

 
19101Z5570 
GOVERNOR
 
 
GOVERNOR

Nissan-Diesel 

 
19200T9304 
GOVERNOR
F 019 Z5E 280 
NP-EP/RLD300-1630A1AFR 
19101Z5574 
GOVERNOR
 
19200T9305 
GOVERNOR
Back to top