105490-5430 ZEXEL GOVERNOR Cross 1054905430 me723020


 

Information governor

ZEXEL 105490-5430 1054905430
MITSUBISHI ME723020 me723020
105490-5430 GOVERNOR
Rating:
12
Buy GOVERNOR 105490-5430 zexel genuine, new aftermarket engine parts with delivery

Cross reference number

Zexel num
Bosch num
Firm num
Name
105490-5430 
105490-5431 
 
ME723020  MITSUBISHI
GOVERNOR
*




Information:


5-9 When moving radial seal, observe correct depth of installation (pressed in). Depth 1 see Fig. 5-9, outside flush with front-end cover.
5-10Depth 2 (after shifting in front-end cover to be flush inside) : max. 1.0 mm.Fig. 5-10Dismantling And Installing The Vee-Belt Tensioner (As from 3 cylinder engine)
Dismantling:
1. Dismantle the holder for the warning system operator. Remove the vee belt driving the cooling air blower.2. Dismantle the vee-belt tensioner. Remove the rubber O-seal on the vee-belt tensioner.Installing:
5-111. Fit a new rubber O-seal on the vee-belt tensioner.Fig. 5-11
5-122. Mount the vee-belt tensioner with the idler pulley facing outwards.Fig. 5-12
5-133. Mount the holder of the warning system operator if the engine is equipped with an alarm system for breakage of the blower belt. Fit a spacer sleeve between the holder and front cover.Fig. 5-13
5-144. Check the alignment of the vee belt running from the idler pulley to the belt pulley mounted on the crankshaft.Fig. 5-145. If misalignment has to be corrected dismantle the vee-belt idler pulley.Checking And Repairing The Vee-Belt Tensioner
Tensioner is removed.
5-151. If the idler is damaged or its bearing worn, dismantle it from the tensioning lever. Check the radial clearance of the shaft of the vee-belt tensioner.Fig. 5-152. If the shaft has too much radial clearance or if the torsion spring is weak or broken, dismantle the vee-belt tensioner.
5-163. After prising out the shaft seal, press out the bearing bushings that are to be renewed. Press in new bearing bushing flush on the inside. Before pressing in the outer bearing bushing, measure the height of the shaft seal and then press in the bearing bushing deeper by this amount.Fig. 5-164. Press in shaft seal flush on outside.
5-175. Renew worn shaft. Drive the heavy-duty clamping sleeve into the large bore so that one end projects 15 mm.Fig. 5-17
5-186. To install, insert the end of the shaft at the inside. Press the end of the torsion spring into the clamping sleeve and push in the shaft completely.Fig. 5-18 If the ends of the torsion spring are of different length, insert the longer one in the clamping sleeve.7. Fit two new gaskets in the groove between the housing and shaft.
5-198. Press the tensioning lever on the shaft so that their holes are in register, with the tensioning lever pointing to the right and the long end of the clamping sleeve pointing downwards (as viewed from inside).Fig. 5-19
5-209. Assemble the idler with the old shims to the tensioning lever.Fig. 5-20Reassembling The Vee-Belt Tensioner (New Design)
Bearing bushing and shaft seal are already fitted.
5-211. Insert long end of torsion spring into shaft and place spacer washer (arrow) in position.Fig. 5-21
5-222. Insert shaft with torsion spring and spacer washer into housing. Position for short end of torsion spring - see arrow.Fig. 5-22
5-233. Push the tensioning lever onto the shaft so that the bores of shaft and lever coincide and the long end of the spring points downwards. Insert locking pin.Fig. 5-23
5-244. Assemble the idler pulley with the old shims to the tensioning lever.Fig. 5-24Dismantling And Installing

Have questions with 105490-5430?





Group cross 105490-5430 ZEXEL

Mitsubishi 

9 420 613 553 
NP-EP/RFD200/1450AF23CSL 
ME723166 
GOVERNOR
9 420 613 554 
NP-EP/RFD200/1450AF23CBL 
ME723009 
GOVERNOR
F 019 Z5E 100 
NP-EP/RFD200/1450AF23CBL 
ME723167 
GOVERNOR
105490-5430  

105490-5431 
 
ME723020 
GOVERNOR
 
ME727052 
GOVERNOR
 
ME723018 
GOVERNOR
9 420 613 555 
NP-EP/RFD200/1650AF9CSL 
ME727053 
GOVERNOR
F 019 Z1E 473 
NP-EP/RFD200/1650AF56DSL 
ME723045 
GOVERNOR
 
ME723264 
GOVERNOR
9 420 613 556 
NP-EP/RFD200/1450AF23CSL 
ME727054 
GOVERNOR
9 420 612 265 
NP-EP/RFD200/1650AF56DSL 
ME723840 
GOVERNOR
9 420 612 266 
NP-EP/RFD200/1650AF56DSL 
ME723842 
GOVERNOR
F 019 Z5E 101 
NP-EP/RFD200/1650AF9CSL 
ME726275 
GOVERNOR
Back to top