105489-2820 ZEXEL F 019 Z5E 027 BOSCH GOVERNOR f019z5e027 1054892820 223005940a


 

Information governor

BOSCH F 019 Z5E 027 f019z5e027
ZEXEL 105489-2820 1054892820
HINO 223005940A 223005940a
105489-2820 GOVERNOR
Rating:
11
Buy GOVERNOR 105489-2820 zexel genuine, new aftermarket engine parts with delivery

Cross reference number

Zexel num
Bosch num
Firm num
Name
105489-2820 
F 019 Z5E 027 
NP-EP/RFD200/1300PF10DJR 
223005940A  HINO
GOVERNOR
K




Information:

Start By:a. remove oil pump1. Check the main bearing caps for identification for their location and direction in the block. The caps must be installed in the same location and direction from which they were removed. Remove No. 2 thru No. 6 bearing caps (1). Remove the thrust plates for the No. 4 main bearing.
If the crankshaft is turned in the wrong direction the tab of the bearing will be pushed between the crankshaft and cylinder block. This can cause damage to either the crankshaft or cylinder block or both.
3. Remove the upper halves of the main bearings by putting tool (A) in oil hole (2) in the crankshaft. Turn the crankshaft in the direction which will push the end of the bearing with a tab out first.4. Remove the lower halves of the bearings from the caps. Install the bearings dry when the clearance checks are made. Put clean engine oil on the bearings for final assembly.5. Install the new bearings in the caps.6. Install the upper halves of the bearings in the cylinder block with tool (A). Be sure tabs (3) on the back of the bearings fit in the tab slots of the caps and cylinder block.The servicemen must be very careful to use Plastigage, tool (B) correctly. The following points must be remembered:...Make sure that the backs of the bearings and the bores are clean and dry....Make sure that the bearing locking tabs are properly seated in their slots....The crankshaft must be free of oil where the Plastigage touches it....If the main bearing clearances are checked with the engine upright or on its side, the crankshaft must be supported. Use a jack under an adjacent crankshaft counterweight and hold the crankshaft against the crown of the bearing. If the crankshaft is not supported, the weight of the crankshaft will cause incorrect readings....Put a piece of Plastigage on the crown of the bearing half that is in the cap. Do not allow the Plastigage to extend over the edge of the bearing....Install the bearing cap using the correct torque-turn specifications. Do not use an impact wrench. Be careful not to dislodge the bearing when the cap is installed....Do not turn the crankshaft with the Plastigage installed....Carefully remove the cap but do not remove the Plastigage. Measure the width of the Plastigage while it is in the bearing cap or on the crankshaft journal. Do this by using the correct scale on the package. Record the measurements....Remove the Plastigage before reinstalling the cap.When using Plastigage, the readings can sometimes be unclear. For example, all parts of the Plastigage are not the same width. Measure the major widths to make sure that they are within the specification range. Also, experience has shown that when checking clearances tighter than 0.10 mm (.004") the readings may be low by 0.013 to 0.025 mm (.0005 to .0010"). Out-of-round journals can give faulty readings. Also, journal taper may be indicated when on end of the Plastigage is wider than the other.For

Have questions with 105489-2820?





Group cross 105489-2820 ZEXEL

Hino 

 
223005810A 
GOVERNOR
9 420 613 691 
NP-EP/RFD200/1300PF10DJR 
223006040A 
GOVERNOR
9 420 613 691 
NP-EP/RFD200/1300PF10DJR 
223006080A 
GOVERNOR
9 420 614 055 
NP-EP/RFD200/1650PF9CHR 
223005680A 
GOVERNOR
9 420 614 055 
NP-EP/RFD200/1650PF9CHR 
223006600A 
GOVERNOR
105489-2820  
F 019 Z5E 027 
NP-EP/RFD200/1300PF10DJR 
223005940A 
GOVERNOR
9 420 614 048 
 
GOVERNOR
 
 
GOVERNOR

Hino 

9 420 614 056 
NP-EP/RFD200/1300PF10DJR 
223005790A 
GOVERNOR
F 019 Z5E 028 
NP-EP/RFD200/1300PF10DJR 
223005800A 
GOVERNOR

Mitsubishi 

9 420 613 539 
NP-EP/RFD200/1400PF31DJR 
ME727932 
GOVERNOR
9 420 613 540 
NP-EP/RFD200/1400PF31DJR 
ME727934 
GOVERNOR

Hino 

 
223006020A 
GOVERNOR
 
223007640A 
GOVERNOR
 
223006021A 
GOVERNOR
F 019 Z1F 030 
223006022A 
GOVERNOR

Mitsubishi 

F 01G 29N 016 
ME727943 
GOVERNOR
Back to top