105488-9232 ZEXEL GOVERNOR Cross 1054889232 1157702560


 

Information governor

ZEXEL 105488-9232 1054889232
ISUZU 1157702560 1157702560
105488-9232 GOVERNOR
Rating:
38
Buy GOVERNOR 105488-9232 zexel genuine, new aftermarket engine parts with delivery

Cross reference number

Zexel num
Bosch num
Firm num
Name
105488-9232 
 
1157702560  ISUZU
GOVERNOR
* K




Information:

(1) Thickness of spacer plate ... 8.585 0.025 mm (.3379 .0009 in)Thickness of gasket that is placed between spacer plate and cylinder block ... 0.208 0.025 mm (.0081 .0009 in)Height of liner over spacer plate, under installation pressure ... 0.13 0.08 mm (.005 .003 in)(2) Height of four dowels above top surface of cylinder block:End dowels (Put 7M7456 Bearing Mount Compound on two end dowels at installation) ... 18.5 0.5 mm (.73 .02 in)Middle dowels ... 16.0 0.5 mm (.63 .02 in)(3) Dimension (new) from centerline of crankshaft bearing bore to top of block (top deck) ... 425.45 0.15 mm (16.750 .006 in)Minimum dimension from centerline of crankshaft bearing bore to top of block (top deck) ... 425.02 mm (16.733 in) The flatness across the whole contact surface of the block must be within 0.10 mm (.004 in) and within 0.05 mm (.002 in) for any 177 mm (7.0 in) section of the surface. The surface finish specification is 3.2 micrometers (125 micro-inches) maximum.(4) Bore in block for camshaft bearings ... 76.835 0.018 mm (3.0250 .0007 in) Install bearings with the oil holes in the bearings on the horizontal centerline. Make sure the bearing joint position is above the oil holes.(5) Bore in the block for the main bearings: Standard, original size (new) ... 129.891 0.013 mm (5.1138 .0005 in)0.64 mm (.025 in) larger than original size ... 130.526 0.013 mm (5.1388 .0005 in)(6) Distance from front of rear face of cylinder block to end of dowels ... 19.1 0.05 mm (.75 .02 in)(7) Width of main bearing cap ... 215.900 0.013 mm (8.5000 .0005 in)Width of block for main bearing cap ... 215.900 0.013 mm (8.5000 .0005 in)Clearance between main bearing cap and cylinder block ... 0.025 mm (.0009 in) tight to 0.025 mm (.0009 in) loose
Tightening Procedure For Main Bearings(8) Torque for the bolts that hold the caps for the main bearings: Install the main bearing caps with the marks (arrow) toward the front of the engine. Install each cap in the correct position by putting the number stamped on the bottom of the cap toward the corresponding number cast on left side of the cylinder block at the pan rail.a. Put 2P2506 Thread Lubricant on the threads of the bolts.b. Tighten the bolts first on the bearing tab side of the cap to ... 260 14 N m (190 10 lb ft)c. Tighten the bolts on the opposite side to ... 260 14 N m (190 10 lb ft)d. Put a mark on each bolt and cap.e. Tighten the bolts on the opposite side, from the mark ... 120 5°f. Tighten the bolts on the bearing tab side of the cap, from the mark ... 120 5°(9) Dimension (new) from centerline of crankshaft bearing bore to bottom of block (pan rails) ... 165.10 0.10

Have questions with 105488-9232?





Group cross 105488-9232 ZEXEL

Hino 

 
223003220A 
GOVERNOR
F 019 Z9E 406 
NP-EP/RFD200/1400PF31DHR 
 
GOVERNOR

Hino 

F 019 Z4E 957 
NP-EP/RFD200/1650PF25CHR 
223003160A 
GOVERNOR
F 019 Z4E 958 
NP-EP/RFD200/1650PF25CHR 
223003270A 
GOVERNOR
F 019 Z4E 958 
NP-EP/RFD200/1650PF25CHR 
223003420A 
GOVERNOR

Isuzu 

 
1157207340 
GOVERNOR
105488-9232  
 
1157702560 
GOVERNOR
 
1157206880 
GOVERNOR
F 019 Z1E 175 
1157704240 
GOVERNOR
 
1157206890 
GOVERNOR

Mitsubishi 

 
ME717229 
GOVERNOR
 
ME726067 
GOVERNOR
F 019 Z4E 959 
NP-EP/RFD200/1300PF10DWR 
ME730214 
GOVERNOR
 
ME717230 
GOVERNOR
 
ME726068 
GOVERNOR
F 019 Z2E 638 
NP-EP/RFD200/1300PF10DWR 
ME730298 
GOVERNOR
 
ME717231 
GOVERNOR
 
ME726069 
GOVERNOR
 
ME730299 
GOVERNOR
F 019 Z4E 960 
NP-EP/RFD200/1300PF10DWR 
ME748919 
GOVERNOR

Nissan-Diesel 

9 420 613 400 
NP-EP/RFD200/1650PF9BGR 
1910197210 
GOVERNOR
Back to top