105487-3090 ZEXEL GOVERNOR Cross 1054873090 me722824


 

Information governor

ZEXEL 105487-3090 1054873090
MITSUBISHI ME722824 me722824
105487-3090 GOVERNOR
Rating:
52
Buy GOVERNOR 105487-3090 zexel genuine, new aftermarket engine parts with delivery

Cross reference number

Zexel num
Bosch num
Firm num
Name
105487-3090 
105487-3091 
 
ME722824  MITSUBISHI
GOVERNOR
*




Information:

Start By:a. remove fuel injection lines 1. Remove bolt (1) and clamp (2) from the fuel injection nozzles to be removed.2. Install Tool (A) with the inside lip of the puller on the lower stepped diameter of the nozzle and the tip of the button in the threaded hole for bolt (1).
Do not exceed a torque of 17 N m (150 lb in) on the screw of Tool (A) during removal of the nozzle. Added force can cause the stem of the nozzle to bend or break off.
3. Tighten the screw of Tool (A) to a maximum torque of 17 N m (150 lb in) to remove fuel injection nozzle (3).4. If the fuel injection nozzle can not be removed with a maximum torque of 17 N m (150 lb in) on the screw of Tool (A), remove Tool (A).
Typical Example5. Remove the protective cap from fuel injection nozzle (3), and install Tool (B) as shown.
Hold Tool (B) so the center line of the tool is in alignment with the centerline of fuel injection nozzle (3). This will prevent distortion of the nozzle which can cause it to bend or break off during removal.
6. Remove the fuel injection nozzle with Tool (B).7. If Tool (B) was used to remove the fuel injection nozzle, replace the nozzle.8. If Tool (A) was used to remove the fuel injection nozzle, remove the carbon dam seal on the end of the nozzle.Install Fuel Injection Nozzle
1. Use Tool (C) to clean the bore for the fuel injection nozzle. Use an open end wrench or tap driver to turn Tool (C).2. Make reference to Special Instruction, Form No. SEHS7292, for the use of Tool (D). Clean the fuel injection nozzle with Tool (D). 3. Install a new seal (4) on fuel injection nozzle (3).4. Put carbon dam seal (5) on the small end of Tool (E). Expand the carbon dam seal by sliding it to the large end. Put Tool (E) against the fuel injection nozzle. Slide carbon dam seal (5) off Tool (E) on to the nozzle. Slide the carbon dam seal into position in the groove on the nozzle as shown. 5. Put fuel injection nozzle (3) in position in the cylinder head. Install clamp (2) and bolt (1) to hold the nozzle in position.End By:a. install fuel injection lines

Have questions with 105487-3090?





Group cross 105487-3090 ZEXEL

Mitsubishi 

 
ME722710 
GOVERNOR
F 019 Z4E 767 
NP-EP/RFD200/1400PF31DSR 
ME722951 
GOVERNOR
F 019 Z4E 768 
NP-EP/RFD200/1400PF31DSR 
ME722769 
GOVERNOR
 
ME722822 
GOVERNOR
 
ME722739 
GOVERNOR
F 019 Z1E 432 
NP-EP/RFD200/1650PF9CGR 
ME726577 
GOVERNOR
 
ME722823 
GOVERNOR
 
ME722741 
GOVERNOR
 
ME723154 
GOVERNOR
F 019 Z4E 769 
NP-EP/RFD200/1650PF9CGR 
ME726276 
GOVERNOR
 
ME722726 
GOVERNOR
9 420 612 291 
NP-EP/RFD200/1300PF10DGR 
ME726578 
GOVERNOR
 
ME722727 
GOVERNOR
F 019 Z4E 770 
NP-EP/RFD200/1300PF10DGR 
ME726579 
GOVERNOR
 
ME722725 
GOVERNOR
F 019 Z4E 771 
NP-EP/RFD200/1650PF9CGR 
ME726580 
GOVERNOR
F 019 Z4E 772 
NP-EP/RFD200/1700PF37CSR 
ME722750 
GOVERNOR
105487-3090  

105487-3091 
 
ME722824 
GOVERNOR
F 019 Z4E 773 
NP-EP/RFD200/1650PF9CGR 
ME726581 
GOVERNOR
Back to top