105487-3061 ZEXEL F 019 Z4E 770 BOSCH GOVERNOR f019z4e770 1054873061 me726579


 

Information governor

BOSCH F 019 Z4E 770 f019z4e770
ZEXEL 105487-3061 1054873061
MITSUBISHI ME726579 me726579
105487-3061 GOVERNOR
Rating:
48
Buy GOVERNOR 105487-3061 zexel genuine, new aftermarket engine parts with delivery

Include in #1:

106671-7461 as GOVERNOR

Cross reference number

Zexel num
Bosch num
Firm num
Name
105487-3061 
F 019 Z4E 770 
NP-EP/RFD200/1300PF10DGR 
ME726579  MITSUBISHI
GOVERNOR
K




Information:

Start By:a. remove oil pump1. Check the connecting rods and caps for their identification and location. 2. Turn the crankshaft until the connecting rod caps are in position.3. Remove two bolts (1) and the cap from the connecting rod. Remove the lower half of the bearing from the cap.4. Push the connecting rod away from the crankshaft. Remove the upper half of the bearing from the connecting rod. Install the bearings dry when the clearance checks are made. Put clean engine oil on the bearings for final assembly.5. Install the upper half of the bearing in the connecting rod.6. Pull the connecting rod slowly on to the crankshaft.7. Install the lower half of the bearing in the cap. Be sure the tabs in the back of bearings are in the tab grooves of the connecting rod and cap.The serviceman must be very careful to use Plastigage, Tool (A) correctly. The following points must be remembered:Make sure that the backs of the bearings and the bores are clean and dry.Make sure that the bearing locking tabs are properly seated in their slots.The crankshaft must be free of oil where the Plastigage touches it.Put a piece of Plastigage (A) on the crown of the bearing half that is in the cap. Do not allow the Plastigage to extend over the edge of the bearing.Install the bearing cap using the correct torque-turn specifications. Do not use an impact wrench. Be careful not to dislodge the bearing when the cap is installed.Do not turn the crankshaft with the Plastigage installed.Carefully remove the cap but do not remove the Plastigage. Measure the width of the Plastigage while it is in the bearing cap or on the crankshaft journal. Do this by using the correct scale on the package. Record the measurements.Remove the Plastigage before reinstalling the cap.When using Plastigage, the readings can sometimes be unclear. For example, all parts of the Plastigage are not the same width. Measure the major widths to make sure that they are within the specification range. Also, experience has shown that when checking clearances tighter than 0.10 mm (.004 in) the readings may be low by 0.013 to 0.025 mm (.0005 to .0010 in). Out-of-round journals can give faulty readings. Also, journal taper may be indicated when one end of the Plastigage is wider that the other.For complete details concerning measuring bearing clearance, see the topic, "Engine Bearings & Crankshafts", SEBD0531. 8. Use Plastigage (A) to check the bearing clearance.9. Put Plastigage (A) on the bearing.10. Put 2P2506 Thread Lubricant on the threads of the rod bolts and seat surfaces of the nuts. Be sure the cylinder numbers on the rod cap and rod are the same and are on the same side of connecting rod. Numbers are on the same side of the rod and cap as are the bearing tab slots. If new rods are installed, put the cylinder number on the rod and cap. Do not turn the crankshaft when Plastigage (A) is in position.

Have questions with 105487-3061?





Group cross 105487-3061 ZEXEL

Mitsubishi 

 
ME722710 
GOVERNOR
F 019 Z4E 767 
NP-EP/RFD200/1400PF31DSR 
ME722951 
GOVERNOR
F 019 Z4E 768 
NP-EP/RFD200/1400PF31DSR 
ME722769 
GOVERNOR
 
ME722822 
GOVERNOR
 
ME722739 
GOVERNOR
F 019 Z1E 432 
NP-EP/RFD200/1650PF9CGR 
ME726577 
GOVERNOR
 
ME722823 
GOVERNOR
 
ME722741 
GOVERNOR
 
ME723154 
GOVERNOR
F 019 Z4E 769 
NP-EP/RFD200/1650PF9CGR 
ME726276 
GOVERNOR
 
ME722726 
GOVERNOR
9 420 612 291 
NP-EP/RFD200/1300PF10DGR 
ME726578 
GOVERNOR
 
ME722727 
GOVERNOR
105487-3061  
F 019 Z4E 770 
NP-EP/RFD200/1300PF10DGR 
ME726579 
GOVERNOR
 
ME722725 
GOVERNOR
F 019 Z4E 771 
NP-EP/RFD200/1650PF9CGR 
ME726580 
GOVERNOR
F 019 Z4E 772 
NP-EP/RFD200/1700PF37CSR 
ME722750 
GOVERNOR
 
ME722824 
GOVERNOR
F 019 Z4E 773 
NP-EP/RFD200/1650PF9CGR 
ME726581 
GOVERNOR
Back to top