106086-5350 ZEXEL FUEL-INJECTION PUMP Cross 1060865350 me066158


 

Information fuel-injection pump

ZEXEL 106086-5350 1060865350
MITSUBISHI ME066158 me066158
106086-5350 FUEL-INJECTION PUMP
Rating:
11
Buy FUEL-INJECTION PUMP 106086-5350 zexel genuine, new aftermarket engine parts with delivery

Cross reference number

Zexel num
Bosch num
Firm num
Name
106086-5350 
 
ME066158  MITSUBISHI
FUEL-INJECTION PUMP
* Q




Information:


Table 1
Required Parts
Item Qty Part Number Description Former Part Number
1 1 560-4252 Bracket 431-8663
2 1 396-3862 (1) Control Harness As 396-3862 (1)
524-5527 (2) Control Harness As 524-5527 (2)
3 1 471-4176 Hose As 380-9241
4 - 7K-1181 Cable Strap NA
5 - 3E-6909 Clip NA
(1) FMC 1 - 772 (Not Equipped with DEF Quality Sensor)
(2) FMC 773 - Up (Equipped with DEF Quality Sensor)Note: These parts should be ordered and replaced only if there is evidence of damage to any part.Rework Procedure
Park the machine on level ground, lower all implements to the ground, shut off machine, and relieve all hydraulic system pressure.
Read and understand this Rework Procedure before starting work.
Illustration 1 g06340431
General location and reference Views
DEF tank cover not shown for clarity.
(A) Fuel tank
(B) Diesel Exhaust Fluid (DEF) module group
See Illustration for the general location of the DEF Module Group and reference views that will be used in future steps.
Illustration 2 g06340436
Location of hardware.
(C) Hardware
(D) DEF fill hose
(E) Clamp
Inspect control harness assembly (2) at location (AA) and hose assembly (3) at location (BB) for rubbing and or fouling on the DEF Tank Cover. If either item is damaged, replace the damaged part.Note: Hardware (C) holding the DEF Module Group to the fuel tank and clamp (E) holding DEF Fill Hose (D) to the tank will need to be loosened to reposition the DEF Module Group to access control harness assembly (2) and hose assembly (3).
After control harness assembly (2) and hose assembly (3) have been inspected and found without damage OR replaced, secure both parts using Steps 6 through 9.
Illustration 3 g06340441
Left view
Fuel tank not shown.
(F) Diesel exhaust fluid module
Illustration 4 g06340446
Location CC
(G) Harness bundled to avoid fouling
Illustration 5 g06340447
Location DD
(H) Terminating resistor
Secure control harness assembly (2) and hose assembly (3) to left side of DEF Module using tie straps (4).Reference: Refer to Illustrations 3, 4, and 5.Note: At location (CC), use tie straps to secure harness bundles to prevent harness from contacting the fuel tank. (See Illustration 4).Note: At location (DD), use tie straps (4) to secure control harness assembly (2) and hose assembly (3), and terminating resistor (H) at lower location. (See Illustration 5).
Illustration 6 g06340448
Location of hardware
(C) Hardware
(E) Clamp
Reposition the DEF Module Group, install bracket (1), and reinstall the remaining hardware (C), clamp (E) removed in Step 4. Check to make sure control harness assembly (2) and hose assembly (3) will not

Have questions with 106086-5350?





Group cross 106086-5350 ZEXEL

9 410 613 014 
NP-PE8P110/921/4RS1NP67 
 
FUEL-INJECTION PUMP

Nissan-Diesel 

9 410 613 870 
1671197516 
FUEL-INJECTION PUMP
9 410 613 015 
NP-PE8P110/921/4RS1NP68 
1671197517 
FUEL-INJECTION PUMP
9 410 613 871 
 
FUEL-INJECTION PUMP

Nissan-Diesel 

 
1671197519 
FUEL-INJECTION PUMP
 
1671197518 
FUEL-INJECTION PUMP

Mitsubishi 

 
ME066154 
FUEL-INJECTION PUMP
9 410 613 016 
NP-PE8P110/721RS3000NP66 
ME726303 
FUEL-INJECTION PUMP
106086-5350  
 
ME066158 
FUEL-INJECTION PUMP
9 410 613 017 
NP-PE8P110/721RS3000NP67 
ME726347 
FUEL-INJECTION PUMP

Nissan-Diesel 

 
1671197561 
FUEL-INJECTION PUMP
 
1671197560 
FUEL-INJECTION PUMP

Mitsubishi 

 
ME069720 
FUEL-INJECTION PUMP
 
ME069724 
FUEL-INJECTION PUMP
9 410 610 103 
NP-PE8P110/721RS3000NP98 
 
FUEL-INJECTION PUMP
Back to top