104660-4373 ZEXEL 9 461 620 043 BOSCH FUEL-INJECTION PUMP 9461620043 1046604373


 

Information fuel-injection pump

BOSCH 9 461 620 043 9461620043
ZEXEL 104660-4373 1046604373
104660-4373 FUEL-INJECTION PUMP
Rating:
15
Buy FUEL-INJECTION PUMP 104660-4373 zexel genuine, new aftermarket engine parts with delivery

Include in #2:

104760-4373 as FUEL INJECTION PUMP

Cross reference number

Zexel num
Bosch num
Firm num
Name
104660-4373 
104660-4374 
9 461 620 043 
   
FUEL-INJECTION PUMP
* Q




Information:

1. Defective Upper O-ring On Unit Injectors Or Leaking Unit Injector Using the fuel priming pump, pressurize the fuel system to 689 kPa (100 psi). Check for fuel on the top deck of the cylinder head (a small amount of leakage is normal from the injector plunger barrel area after 5 minutes of constant pressure). If fuel is found, drain the fuel supply manifold. Remove each unit injector (see 3176 Vehicular Diesel Engine Disassembly and Assembly, Form No. SENR4965), and check for a defective upper O-ring on the unit injector or if the unit injector itself is leaking.A bad injector to sleeve seat causes combustion gas leakage that can damage the injector O-rings. Inspect injector hold down bolt thread depth for a minimum of 25 mm (.984 in) of thread depth in the cylinder head.Testing of the injectors must be done off of the engine. Use the 1U6661 Pop (Injector) Tester Group with a 1U6663 Injector Holding Block, and a 1U6665 Power Supply, to test the injectors. For the test procedure refer to Special Instruction, Form No. SEHS8867, Using The 1U6661 Pop (Injector) Tester. For test specifications refer to Special Instruction, Form No. SEHS8804, Unit Injector Test Specifications for 1.7 Liter Engines. Inspect and repair as necessary the sealing surface (seat) of the injector sleeve in the cylinder head when removing and installing an injector. The injector sealing surface (seat) must be free of scratches or evidence of combustion products. If it is necessary to rework (ream) or replace the sleeve use 4C4054 Tool Group and refer to Special Instruction, Form No. SEHS9246, Using The 4C4054 Unit Injector Sleeve Replacement Tool Group.2. Injector Not Seated Properly A bad injector to sleeve seat causes combustion gas leakage that can damage the injector o-rings. Inspect injector hold down bolt thread depth for a minimum of 25 mm (.984 in) of thread depth in the cylinder head.Torque fuel injector hold down bolt to 33 7 N m (24 5 lb ft). Inspect and repair as necessary the sealing surface (seat) of the injector sleeve in the cylinder head when removing and installing an injector. The injector sealing surface (seat) must be free of scratches or evidence of combustion products. If it is necessary to rework (ream) or replace the sleeve use 4C4054 Tool Group and refer to Special Instruction, Form No. SEHS9246, Using The 4C4054 Unit Injector Sleeve Replacement Tool Group.3. Crack(s) In Cylinder Head Pressurize the fuel gallery and check for crack(s). Crack(s) between the cylinder head fuel passages and passages open to the crankcase will allow fuel to enter the crankcase.4. Porosity In Cylinder HeadPressurize the fuel gallery and check for porosity. Leakage may be due to the proximity of the hole to internal fuel passages.

Have questions with 104660-4373?





Group cross 104660-4373 ZEXEL

9 461 618 104 
 
FUEL-INJECTION PUMP
9 461 622 835 
 
FUEL-INJECTION PUMP
9 461 622 836 
 
FUEL-INJECTION PUMP
9 461 622 837 
 
FUEL-INJECTION PUMP
9 461 622 838 
NP-VE6/10F2000RNP84 
 
FUEL-INJECTION PUMP
9 461 622 839 
NP-VE6/10F1750RNP85 
 
FUEL-INJECTION PUMP
9 461 620 041 
NP-VE6/10F1400RNP87 
 
FUEL-INJECTION PUMP
9 461 622 840 
 
FUEL-INJECTION PUMP
9 461 622 841 
 
FUEL-INJECTION PUMP
9 461 620 042 
 
FUEL-INJECTION PUMP
9 461 618 886 
NP-VE6/10F1750RNP88 
 
FUEL-INJECTION PUMP
9 461 616 111 
 
FUEL-INJECTION PUMP
104660-4373  

104660-4374 
9 461 620 043 
 
FUEL-INJECTION PUMP
9 461 618 887 
NP-VE6/10F1750RNP89 
 
FUEL-INJECTION PUMP
9 461 616 112 
 
FUEL-INJECTION PUMP
9 461 620 044 
NP-VE6/10F2000RNP121 
 
FUEL-INJECTION PUMP
Back to top