104649-0710 ZEXEL 9 461 616 105 BOSCH FUEL-INJECTION PUMP 9461616105 1046490710


 

Information fuel-injection pump

BOSCH 9 461 616 105 9461616105
ZEXEL 104649-0710 1046490710
104649-0710 FUEL-INJECTION PUMP
Rating:
14
Buy FUEL-INJECTION PUMP 104649-0710 zexel genuine, new aftermarket engine parts with delivery

Include in #2:

104749-0710 as FUEL INJECTION PUMP

Cross reference number

Zexel num
Bosch num
Firm num
Name
104649-0710 
104649-0711 
9 461 616 105 
   
FUEL-INJECTION PUMP
* Q




Information:

start by:a) remove fuel injection pump housing and governor 1. Install the fuel injection pump housing on tool (A).2. Remove the bolts (1) that hold the governor housing (2) to the fuel injection pump housing.3. Remove the governor housing (2). 4. Remove two springs (4) and the seat (5) from the governor housing.5. Remove the seat (7) from the shaft.6. Remove the spring (6) from the shaft.7. Remove the cover (3) from the pump housing. 8. Remove the shaft (8) and the lever (9) from the pump housing. 9. Remove the thrust collar (11) from the shaft.10. Remove the cover (10) from the pump housing. 11. Loosen the two bolts (13) that hold the torque spring assembly (12) and remove it from the pump housing. 12. Remove the pin (15) from the pump housing.13. Remove the screw (14) and the nut (16) from the pump housing.14. Remove the ring that holds the lever and remove the lever (18) from the dowel (17).15. Remove the dowel (17) from the pump housing. Dowel does not need to be removed unless camshaft is to be removed.
Pull on the shield only a small amount in each location so it will not have distortion or damage. A damaged shield must be replaced.
16. Remove the shield (19) from the camshaft with tool (B). 17. Install the timing pin (C) to hold the camshaft.18. Remove the bolts (20) that hold the flyweight assembly to the camshaft. 19. Remove the flyweight assembly (21) from the camshaft.20. Remove the timing pin (C) from the pump housing.Connection Of Governor To Fuel Injection Pump Housing
1. Put the fuel injection pump housing on the bracket assembly (A).2. Install the timing pin (B) to hold the camshaft.3. Put the flyweight assembly (1) in position on the camshaft. Be sure the pin that holds the shaft (2) is in position on the back of the flyweight assembly.4. Install the bolts that hold the flyweight assembly to the camshaft and tighten to a torque of 10 2 lb. ft. (1.38 0.28 mkg).5. Remove the timing pin (B). 6. Put the shield (3) in position over the flyweights. 7. Use the driver (C) to install the shield the remainder of the way on to the camshaft. 8. Put a new O-ring seal on the dowel (4) and install the dowel in the pump housing. Make the dowel even with the machined surface of the counterbore on the outside of the housing. 9. Put the lever (8) on the dowel (4) and install the ring that holds it on the dowel.10. Install the screw (6) and the nut (7) in the pump housing.11. Install the pin (5) in the pump housing. 12. Put the torque spring assembly (10) in position on the housing and tighten the two bolts (11) that hold it to the housing.13. Install the cover (9) on the pump housing. 14. Put the thrust collar (13) in position between the flyweights. Lift the flyweights up with a piece of wire

Have questions with 104649-0710?





Group cross 104649-0710 ZEXEL

104649-0710  

104649-0711 
9 461 616 105 
 
FUEL-INJECTION PUMP
9 461 620 539 
NP-VE4/9F2150RNP1064 
 
FUEL-INJECTION PUMP
9 461 618 101 
 
FUEL-INJECTION PUMP
9 461 618 102 
NP-VE4/9F2150RNP1040 
 
FUEL-INJECTION PUMP
9 461 620 540 
 
FUEL-INJECTION PUMP
9 461 620 541 
 
FUEL-INJECTION PUMP
9 461 618 874 
NP-VE4/9F2150RNP1066 
 
FUEL-INJECTION PUMP
9 461 620 542 
 
FUEL-INJECTION PUMP
9 461 620 543 
 
FUEL-INJECTION PUMP
9 461 620 544 
NP-VE4/9F2150RNP1566 
 
FUEL-INJECTION PUMP
9 461 620 545 
 
FUEL-INJECTION PUMP
9 461 620 546 
 
FUEL-INJECTION PUMP
9 461 617 021 
 
FUEL-INJECTION PUMP
9 461 618 103 
 
FUEL-INJECTION PUMP
9 461 615 855 
 
FUEL-INJECTION PUMP
9 461 617 809 
 
FUEL-INJECTION PUMP
Back to top