Information fuel-injection pump
BOSCH
9 461 614 861
9461614861
ZEXEL
104641-6211
1046416211
ISUZU
8970395390
8970395390
Rating:
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
Nayuank Fuel Injection Pump 104641-6211 8970395390 8943413081 Fits For Isuzu Engine 4JB1 Fits For Bobcat Skid Steer Loader 843 853 1213
Nayuank Part Name: Fuel Injection Pump || Part Number: 104641-6211 8970395390 Note: Please check the fitment carefully before purchase. Or just tell us the part number you need. || Engine Model: 4JB1 || Applicable: Fits For Isuzu Engine 4JB1 || Fits For Bobcat Skid Steer Loader 843 853 1213
Nayuank Part Name: Fuel Injection Pump || Part Number: 104641-6211 8970395390 Note: Please check the fitment carefully before purchase. Or just tell us the part number you need. || Engine Model: 4JB1 || Applicable: Fits For Isuzu Engine 4JB1 || Fits For Bobcat Skid Steer Loader 843 853 1213
Nayuank Fuel Injection Pump 104641-6211 8970395390 1046416211 Fits For Isuzu Engine 4JB1 Fits For Bobcat Skid Steer Loader 843 853 1213
Nayuank Part Name: Fuel Injection Pump || Part Number: 104641-6211 8970395390 1046416211 Note: Please check the fitment carefully before purchase. Or just tell us the part number you need. || Engine Model: 4JB1 || Applicable: Fits For Isuzu Engine 4JB1 || Fits For Bobcat Skid Steer Loader 843 853 1213
Nayuank Part Name: Fuel Injection Pump || Part Number: 104641-6211 8970395390 1046416211 Note: Please check the fitment carefully before purchase. Or just tell us the part number you need. || Engine Model: 4JB1 || Applicable: Fits For Isuzu Engine 4JB1 || Fits For Bobcat Skid Steer Loader 843 853 1213
You can express buy:
USD 395.34
17-05-2025
17-05-2025
For ISUZU 4JB1 Diesel Engine Fuel Injection Pump 9-46161486-1 8-97039839-0 104641-6211 104641-6212
USD 2330.9
16-05-2025
16-05-2025
QIANYU Fuel Pump 9 461 614 861 Diesel Engine Fuel Injector Pump VE411F1300LNP761 104641-6211
Images:
USD 2330.9
[16-May-2025]
USD 411.32
[13-May-2025]
USD 388.94
[13-May-2025]
Cross reference number
Zexel num
Bosch num
Firm num
Name
Information:
(1) End play for shaft (new) ... 0.100 0.018 mm (.0039 .0007 in)Maximum permissible end play (worn) ... 0.20 mm (.008 in)(2) Thickness of thrust bearing (where thrust rings contact bearing) ... 5.372 0.013 mm (.2115 .0005 in)(3) Tighten both band clamps with procedure that follows:a. Tighten to ... 10.2 0.7 N m (90 6 lb in)b. Tap (hit) clamp lightly all around.c. Tighten again to ... 10.2 0.7 N m (90 6 lb in)
Do not overtighten the clamps.
(4) Diameter of shaft (new) ... 11.570 to 11.577 mm (.4555 to .4558 in)Bore in the bearing (new) ... 11.608 to 11.618 mm (.4570 to .4574 in)Maximum permissible clearance between bearing and shaft (worn) ... 0.05 mm (.002 in)(5) Maximum permissible gap of oil seal ring, measured in bore of housing ... 0.25 mm (.010 in)(6) Install the compressor wheel (at room temperature) as follows:a. Put compressor wheel on the shaft.
Do not bend or add stress to the shaft when nut is loosened or tightened.
b. Remove nut from shaft and apply 6V1541 Quick Cure Primer on the threads of the shaft and nut followed by application of 9S3265 Retaining Compound.c. Tighten nut to ... 24.4 1.4 N m (144 4 lb in)(7) Thickness of each thrust ring ... 2.5463 0.0064 mm (.10025 .00025 in)(8) Bore in housing (new) ... 19.050 to 19.075 mm (.7500 to .7510 in)Outside diameter of the bearing (new) ... 18.936 to 18.948 mm (.7455 to .7460 in)Maximum permissible clearance between bearing and bore in housing (worn) ... 0.15 mm (.006 in)Torque for four nuts (put 5P3931 Anti-Seize Compound on threads) and bolts that hold turbocharger to exhaust manifold ... 70 15 N m (50 11 lb ft) Put clean engine oil in the oil inlet of the turbocharger after assembly or before installation to provide start up lubrication and/or storage protection.
Do not overtighten the clamps.
(4) Diameter of shaft (new) ... 11.570 to 11.577 mm (.4555 to .4558 in)Bore in the bearing (new) ... 11.608 to 11.618 mm (.4570 to .4574 in)Maximum permissible clearance between bearing and shaft (worn) ... 0.05 mm (.002 in)(5) Maximum permissible gap of oil seal ring, measured in bore of housing ... 0.25 mm (.010 in)(6) Install the compressor wheel (at room temperature) as follows:a. Put compressor wheel on the shaft.
Do not bend or add stress to the shaft when nut is loosened or tightened.
b. Remove nut from shaft and apply 6V1541 Quick Cure Primer on the threads of the shaft and nut followed by application of 9S3265 Retaining Compound.c. Tighten nut to ... 24.4 1.4 N m (144 4 lb in)(7) Thickness of each thrust ring ... 2.5463 0.0064 mm (.10025 .00025 in)(8) Bore in housing (new) ... 19.050 to 19.075 mm (.7500 to .7510 in)Outside diameter of the bearing (new) ... 18.936 to 18.948 mm (.7455 to .7460 in)Maximum permissible clearance between bearing and bore in housing (worn) ... 0.15 mm (.006 in)Torque for four nuts (put 5P3931 Anti-Seize Compound on threads) and bolts that hold turbocharger to exhaust manifold ... 70 15 N m (50 11 lb ft) Put clean engine oil in the oil inlet of the turbocharger after assembly or before installation to provide start up lubrication and/or storage protection.