104640-8400 ZEXEL 9 461 616 390 BOSCH FUEL-INJECTION PUMP 9461616390 1046408400


 

Information fuel-injection pump

BOSCH 9 461 616 390 9461616390
ZEXEL 104640-8400 1046408400
104640-8400 FUEL-INJECTION PUMP
Rating:
77
Buy FUEL-INJECTION PUMP 104640-8400 zexel genuine, new aftermarket engine parts with delivery

Include in #2:

104740-8400 as FUEL INJECTION PUMP

Cross reference number

Zexel num
Bosch num
Firm num
Name
104640-8400 
9 461 616 390 
NP-VE4/10F2100RNP1041 
   
FUEL-INJECTION PUMP
Q




Information:

Start By:
Do not let the tops of the nozzles turn while the fuel lines are loosened. The nozzles will be damaged if the top of the nozzle turns in the body. Defective fuel nozzles will damage the engine due to improper spray patterns.
a. remove fuel injection lines
Keep all parts clean from contaminants. Contaminants put into the system may cause rapid wear and shortened component life.
1. Remove clamp (1). 2. Install tool (A). Turn screw (2) out until the button on the screw almost makes contact with the inside of the nozzle puller. Tilt the tool approximately 45° and place it over the nozzle.3. Tilt the nozzle puller (A) up so the inside lip of the puller is under the stepped diameter of the nozzle.4. Turn screw (2) down until the button goes into the bolt hole for the nozzle hold down clamp.
Do not exceed a torque of 17 N m (13 lb ft) on the screw in tooling (A) to remove the nozzle. Added force can cause the stem of the nozzle to bend or break off.
5. Turn screw (2) to lift the nozzle out of its bore. If necessary, after the nozzle is loose in its bore, move it up and down to help loosen any carbon and make removal easier. 6. If the nozzle can not be removed with tooling (A), tooling (B) must be used. When tooling (B) is used, the nozzle normally can not be used again, and a new nozzle will need to be installed as a replacement.
Hold tool (B) so the center line of tool (B) is the same as the extended center line of fuel injection nozzle (2). This will prevent distortion of the fuel injection nozzle which can cause the nozzle to bend or break off.
7. Remove the protective cap and install tooling (B).8. Use the slide hammer to remove fuel injection nozzle (3).9. Remove the compression seal.10. For nozzles removed using tool (A), remove the carbon dam seal on the end of the nozzle. The following steps are for the installation of the fuel injection nozzles. Tool (C) must be modified by drilling it out to a diameter of 8.5 mm (.344 in) and to a depth of 1.5 mm (.060 in) before it can be used on the 8N7002 Fuel Injection Nozzle.11. Use tool (C) to install carbon dam seal (4).12. To clean the nozzles, see Special Instruction SEHS7292 for the use of tooling (D).13. Install new compression seal (5). 14. Use tool (E) to clean the bore for the fuel injection nozzle. 15. Install fuel injection nozzle (6).
Do not let the tops of the fuel nozzles turn when the fuel lines are tightened. The nozzles will be damaged if the top of the nozzle turns in the body.
End By:a. install fuel injection lines

Have questions with 104640-8400?





Group cross 104640-8400 ZEXEL

104640-8400  
9 461 616 390 
NP-VE4/10F2100RNP1041 
 
FUEL-INJECTION PUMP
9 461 616 391 
NP-VE4/10F2100RNP1042 
 
FUEL-INJECTION PUMP
9 461 616 392 
 
FUEL-INJECTION PUMP
9 461 616 680 
NP-VE4/10F2100RNP1043 
 
FUEL-INJECTION PUMP
9 461 616 393 
 
FUEL-INJECTION PUMP
9 461 614 794 
NP-VE4/10F2000RNP1049 
 
FUEL-INJECTION PUMP
9 461 622 240 
 
FUEL-INJECTION PUMP
9 461 615 134 
NP-VE4/10F2100RNP968 
 
FUEL-INJECTION PUMP
9 461 616 073 
NP-VE4/10F2100RNP461 
 
FUEL-INJECTION PUMP
9 461 616 394 
NP-VE4/10F2100RNP823 
 
FUEL-INJECTION PUMP
9 461 615 091 
NP-VE4/10F2100RNP969 
 
FUEL-INJECTION PUMP
Back to top