Information fuel-injection pump
BOSCH
9 461 614 041
9461614041
ZEXEL
104640-4733
1046404733
Rating:
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
Fuel Injection Pump 16700-10H05 104740-4734 104640-4733 for Nissan SD25 Engine
FGNTWP Part Number:16700-10H05, 1670010H05, 104740-4734, 1047404734, 9 460 610 412, 9460610412, 104640-4733, 1046404733, 9 461 614 041, 9461614041, 104640-4731, 1046404731, 9 461 612 172, 9461612172, 104640-4732, 1046404732, 9 461 613 586, 9461613586, 16700-10H03, 1670010H03, 104740-4732, 1047404732, 9 460 610 256, 9460610256, 104740-4733, 1047404733, 9 460 610 337, 9460610337 || Applications:for Nissan SD25 Engine
FGNTWP Part Number:16700-10H05, 1670010H05, 104740-4734, 1047404734, 9 460 610 412, 9460610412, 104640-4733, 1046404733, 9 461 614 041, 9461614041, 104640-4731, 1046404731, 9 461 612 172, 9461612172, 104640-4732, 1046404732, 9 461 613 586, 9461613586, 16700-10H03, 1670010H03, 104740-4732, 1047404732, 9 460 610 256, 9460610256, 104740-4733, 1047404733, 9 460 610 337, 9460610337 || Applications:for Nissan SD25 Engine
Fuel Injection Pump 16700-10H05 104740-4734 104640-4733 for Nissan SD25 Engine
DIGERTECH Part number:16700-10H05 || Application: for Nissan SD25 Engine
DIGERTECH Part number:16700-10H05 || Application: for Nissan SD25 Engine
Include in #2:
104740-4734
as FUEL INJECTION PUMP
Cross reference number
Zexel num
Bosch num
Firm num
Name
104640-4733
FUEL-INJECTION PUMP
Q 11CJ FUEL INJECTION PUMP VE4 VE
Q 11CJ FUEL INJECTION PUMP VE4 VE
Information:
It is not necessary to remove the oil pan.1. Remove the coolant from the cooling system.2. Use tooling (A) and remove oil filter (2). 3. Loosen clamps (1) and disconnect the bases.4. Remove bolt (4) and three bolts from behind the oil cooler. 5. Remove oil filter base and engine oil cooler (3) as a unit.Install Engine Oil Cooler And Oil Filter Base
1. Inspect the O-ring seals in the oil filter base. Install new seals if needed. Put oil on the seal. 2. Put oil filter base and oil cooler (1) in position on the engine.3. Install the four bolts that hold the oil cooler in place. 4. Connect the two hoses and install clamps (2).5. Install oil filter (3). See the instructions on the oil filter.Disassemble Engine Oil Cooler And Oil Filter Base
start by:a) remove engine oil cooler and oil filter base1. Remove bolts (1) and make a separation of cover (2) from the oil filter base. 2. Remove nuts (3) and make a separation of the oil cooler from oil filter base (4). 3. Remove divider (6) from oil cooler (5). 4. Remove plug (9), spring (8) and bypass valve (7). 5. Remove plug (12), spring (11) and bypass valve (10) from the oil filter base. Assemble Engine Oil Cooler And Oil Filter Base
1. Put valve (1) and spring (2) in position in oil filter base (4). 2. Install plug (3).3. Put the valve and spring (5) in position and install plug (6). 4. Put divider (7) in position between the fifth and sixth plates from the flange and on the same end as the short stud. 5. Install oil filter base (4) in position on oil cooler (8) and install the nuts. Tighten the nuts to a torque of 22 3 N m (16 2 lb.ft.).6. Install the gasket, cover (9) and the bolts. end by:a) install engine oil cooler and oil filter base
1. Inspect the O-ring seals in the oil filter base. Install new seals if needed. Put oil on the seal. 2. Put oil filter base and oil cooler (1) in position on the engine.3. Install the four bolts that hold the oil cooler in place. 4. Connect the two hoses and install clamps (2).5. Install oil filter (3). See the instructions on the oil filter.Disassemble Engine Oil Cooler And Oil Filter Base
start by:a) remove engine oil cooler and oil filter base1. Remove bolts (1) and make a separation of cover (2) from the oil filter base. 2. Remove nuts (3) and make a separation of the oil cooler from oil filter base (4). 3. Remove divider (6) from oil cooler (5). 4. Remove plug (9), spring (8) and bypass valve (7). 5. Remove plug (12), spring (11) and bypass valve (10) from the oil filter base. Assemble Engine Oil Cooler And Oil Filter Base
1. Put valve (1) and spring (2) in position in oil filter base (4). 2. Install plug (3).3. Put the valve and spring (5) in position and install plug (6). 4. Put divider (7) in position between the fifth and sixth plates from the flange and on the same end as the short stud. 5. Install oil filter base (4) in position on oil cooler (8) and install the nuts. Tighten the nuts to a torque of 22 3 N m (16 2 lb.ft.).6. Install the gasket, cover (9) and the bolts. end by:a) install engine oil cooler and oil filter base