104640-4570 ZEXEL 9 461 611 342 BOSCH FUEL-INJECTION PUMP 9461611342 1046404570


 

Information fuel-injection pump

BOSCH 9 461 611 342 9461611342
ZEXEL 104640-4570 1046404570
104640-4570 FUEL-INJECTION PUMP
Rating:
81
Buy FUEL-INJECTION PUMP 104640-4570 zexel genuine, new aftermarket engine parts with delivery

Include in #2:

104740-4580 as FUEL INJECTION PUMP

Cross reference number

Zexel num
Bosch num
Firm num
Name
104640-4570 
104640-4571 
9 461 611 342 
   
FUEL-INJECTION PUMP
* Q




Information:

White Smoke
Recommended Procedure
1. Cold Outside Temperatures ... When the air outside is cold, the cylinder temperature is cooler. Not all the fuel will burn in the cylinders. The fuel which does not burn comes out the exhaust as white smoke. White smoke is normal in cold temperatures until the engine operates long enough to become warm. There will be less white smoke if No. 1 diesel fuel is used.2. Long Idle Periods ... When an engine runs at idle speed for a long period of time, the cylinders cool and all of the fuel does not burn. Do not idle an engine for a long period of time. Stop an engine when it is not in use. If long idle periods are necessary, use No. 1 diesel fuel.3. Low Quality Fuel ... Test the engine using fuel according to recommendations by Caterpillar.4. Air in Fuel System ... With air in the fuel system the engine will normally be difficult to start, run rough and release a large amount of white smoke. To remove the air from the fuel system open the manual bleed valve on the fuel injection pump housing. Operate the priming pump until the flow of fuel from the manual bleed valve is free of air. Close the manual bleed valve and fasten the fuel priming pump. Start the engine. If the engine still does not run smooth or releases a large amount of white smoke, loosen the fuel line nuts one at a time at the cylinder heads, and permit the fuel to come out until it is free of air. Tighten the fuel line nuts. If air is not removed in this way, put 35 kPa (5 psi) of air pressure to the fuel tank.
Do not use more than 55 kPa (8 psi) of air pressure in the fuel tank or damage to the tank may result.
Check for leakage at the connections between the fuel tank and the fuel transfer pump. If leaks are found, tighten the connections or replace the lines. If there are no visual leaks, remove the fuel supply line from the tank and connect it to an outside fuel supply. If this corrects the problem, the suction line (standpipe) inside the fuel tank has a leak.5. Fuel Injection Timing Not Correct ... Check and make necessary adjustments as per Testing and Adjusting section of this Service Manual.6. Automatic Timing Advance Does Not Operate Correctly ... Check with engine warm. Use the 8T5300 Timing Indicator Group to check the automatic timing advance unit. Check to see that the advance is smooth and that the amount of advance is correct. See Fuel System of the Testing and Adjusting section of this Service Manual for the subject Checking Engine Timing And Automatic Timing Advance Unit With 8T5300 Timing Indicator Group. If the timing indicator is not available, make rapid "acceleration" (increase in speed) from low idle to high idle. Engine must have smooth acceleration. A timing advance that does not operate correctly

Have questions with 104640-4570?





Group cross 104640-4570 ZEXEL

9 461 611 340 
NP-VE4/10F2150RNP297 
 
FUEL-INJECTION PUMP
9 461 625 030 
 
FUEL-INJECTION PUMP
9 461 625 031 
 
FUEL-INJECTION PUMP
9 461 622 606 
 
FUEL-INJECTION PUMP
9 461 612 158 
 
FUEL-INJECTION PUMP
9 461 611 341 
 
FUEL-INJECTION PUMP
9 461 622 607 
 
FUEL-INJECTION PUMP
104640-4570  

104640-4571 
9 461 611 342 
 
FUEL-INJECTION PUMP
F 01G 29X 052 
NP-VE4/10F2150RNP313 
 
FUEL-INJECTION PUMP
9 461 625 032 
 
FUEL-INJECTION PUMP
9 461 625 033 
NP-VE4/10F2150RNP315 
 
FUEL-INJECTION PUMP
Back to top