Information fuel-injection pump
BOSCH
9 461 610 646
9461610646
ZEXEL
104640-4410
1046404410
Rating:
Include in #2:
104740-4420
as FUEL INJECTION PUMP
Cross reference number
Zexel num
Bosch num
Firm num
Name
Information:
(1) Diameter of the surfaces (journals) for the camshaft bearings (new) ... 63.500 0.013 mm (2.5000 .0005 in) Bore in the five bearings for the camshaft (new) ... 63.589 0.038 mm (2.5035 .0015 in)Maximum permissible clearance between bearing and bearing surface (journal) (worn) ... 0.18 mm (.007 in)(2) Tight fit between the gear and camshaft ... 0.030 to 0.071 mm (.0012 to .0028 in) Maximum permissible temperature of the gear for installation on the camshaft (do not use a torch) ... 315°C (600°F)(3) End play for the camshaft ... 0.18 0.08 mm (.007 .003 in) Maximum permissible end play (worn) ... 0.51 mm (.020 in)(4) Width of thrust groove in camshaft (new) ... 9.14 0.05 mm (.360 .002 in) Diameter of thrust pin (new) ... 8.97 0.03 mm (.353 .001 in)Torque for thrust pin ... 48 7 N m (35 5 lb ft)(5) Height of camshaft lobes.To find lobe lift, use the procedure that follows:A. Measure camshaft lobe height (5).B. Measure base circle (7).C. Subtract base circle (Step B) from lobe height (Step A). The difference is actual lobe lift (6).D. Specified camshaft lobe lift (6) is: 9N5230 Camshaft used with roller lifters: a. Exhaust lobe ... 9.40 mm (.370 in) b. Intake lobe ... 9.33 mm (.367 in)2W4238 Camshaft used with flat face lifters: c. Exhaust lobe ... 9.40 mm (.370 in) d. Intake lobe ... 9.06 mm (.357 in)Maximum permissible difference between actual lobe lift (Step C) and specified lobe lift (Step D) is 0.25 mm (.010 in).
Camshaft Gear Assembly
View A-A(8) Distance from the end of 9N5771 Dowell to the face of gear ... 11.81 0.13 mm(.465 .005 in)
View B-B(9) Distance from the end of 5P4283 Dowel to the face of camshaft ... 2.00 0.25 mm(.079 .010 in)Camshaft Installation
For installation of camshaft, the timing mark on the camshaft gear tooth must be in alignment with the timing mark on the tooth space of the crankshaft gear.Intake Valve Timing
1. Check the No. 1 intake valve clearance with the engine stopped. The valve clearance must be 0.30 to 0.46 mm (.012 to .018 in). If the valve clearance is not in this range, adjust the clearance to 0.38 mm (.015 in).2. Mark Top Center Position of the crankshaft on the vibration damper or pulley.3. Use a dial indicator to measure the intake valve movement.4. Rotate the crankshaft in the direction of normal engine rotation. Stop when the intake valve is 1.91 mm (.075 in) off its seat in the opening sequence. At this point the crankshaft must be 10 2° After Top Center.
Camshaft Gear Assembly
View A-A(8) Distance from the end of 9N5771 Dowell to the face of gear ... 11.81 0.13 mm(.465 .005 in)
View B-B(9) Distance from the end of 5P4283 Dowel to the face of camshaft ... 2.00 0.25 mm(.079 .010 in)Camshaft Installation
For installation of camshaft, the timing mark on the camshaft gear tooth must be in alignment with the timing mark on the tooth space of the crankshaft gear.Intake Valve Timing
1. Check the No. 1 intake valve clearance with the engine stopped. The valve clearance must be 0.30 to 0.46 mm (.012 to .018 in). If the valve clearance is not in this range, adjust the clearance to 0.38 mm (.015 in).2. Mark Top Center Position of the crankshaft on the vibration damper or pulley.3. Use a dial indicator to measure the intake valve movement.4. Rotate the crankshaft in the direction of normal engine rotation. Stop when the intake valve is 1.91 mm (.075 in) off its seat in the opening sequence. At this point the crankshaft must be 10 2° After Top Center.