104640-2840 ZEXEL 9 461 617 578 BOSCH FUEL-INJECTION PUMP 9461617578 1046402840


 

Information fuel-injection pump

BOSCH 9 461 617 578 9461617578
ZEXEL 104640-2840 1046402840
104640-2840 FUEL-INJECTION PUMP
Rating:
27
Buy FUEL-INJECTION PUMP 104640-2840 zexel genuine, new aftermarket engine parts with delivery

Include in #2:

104740-2840 as FUEL INJECTION PUMP

Cross reference number

Zexel num
Bosch num
Firm num
Name
104640-2840 
9 461 617 578 
NP-VE4/10F2400LNP1589 
   
FUEL-INJECTION PUMP
Q




Information:

2. Remove nuts (1) from studs for main bearing caps (2).3. Remove the main bearing caps.4. Install rubber hose over each of the two studs at both ends of the block. This will protect the crankshaft during removal and installation. 5. Remove the crankshaft from the cylinder block. Weight of crankshaft is 300 lb. (136 kg).6. Remove the main bearings from cylinder block and main bearing caps.
If main bearings are not replaced, old bearings must be installed in same location from which they were removed.
Install Crankshaft
1. Put timing marks (1) on all timing gears in alignment.2. Clean surfaces for bearings in cylinder block. Install upper halves of bearings in block. Put clean oil on bearings.
If replacement of the bearings is not made, old bearings must be installed in same location from which they were removed.
3. Clean bearing caps, and install lower halves of bearings in caps. 4. Fasten a hoist to crankshaft and put it into place in the block with "V" mark on crankshaft gear in alignment with "V" mark on cluster gear. 5. Check bearing clearance with wire (A). Install bearing caps, and tighten both nuts to 75 5 lb. ft. (101.7 6.8 N m). Put a mark across the nuts and studs, and turn nuts an additional 120° from mark. Remove caps and check thickness of wire (A) to find bearing clearance. Bearing clearance must be .0035 to .0066 in. (0.089 to 0.168 mm) for new parts. Maximum permissible clearance for used parts is .010 in. (0.25 mm).6. Put clean oil on threads of studs, face of nuts, and lower halves of bearings. Put bearing caps in their respective positions with number on cap same as number on block, and groove in bearing cap on same side as groove in cylinder block. Install nuts and tighten to 75 5 lb.ft. (101.7 6.8 N m). Put a mark across the nuts and studs, and turn nuts an additional 120° from mark. 7. Use indicator group (B) to check the crankshaft end plate as controlled by lower bearing of No. 7 bearing cap. End play with new parts should be .006 to .018 in. (0.15 to 0.46 mm). Maximum permissible end play with used parts is .035 in. (0.89 mm).end by: a) install flywheel housingb) install front coverc) install pistonsd) install engine and torque divider

Have questions with 104640-2840?





Group cross 104640-2840 ZEXEL

9 461 619 963 
 
FUEL-INJECTION PUMP
9 461 618 834 
NP-VE4/10F2500LNP1562 
 
FUEL-INJECTION PUMP
9 461 618 835 
NP-VE4/10F2500LNP1142 
 
FUEL-INJECTION PUMP
104640-2840  
9 461 617 578 
NP-VE4/10F2400LNP1589 
 
FUEL-INJECTION PUMP
9 461 619 964 
NP-VE4/10F1800LNP1631 
 
FUEL-INJECTION PUMP
9 461 618 346 
NP-VE4/10F2500LNP1789 
 
FUEL-INJECTION PUMP
Back to top