104640-2532 ZEXEL 9 461 622 594 BOSCH FUEL-INJECTION PUMP 9461622594 1046402532


 

Information fuel-injection pump

BOSCH 9 461 622 594 9461622594
ZEXEL 104640-2532 1046402532
104640-2532 FUEL-INJECTION PUMP
Rating:
16
Buy FUEL-INJECTION PUMP 104640-2532 zexel genuine, new aftermarket engine parts with delivery

Include in #2:

104740-2532 as FUEL INJECTION PUMP

Cross reference number

Zexel num
Bosch num
Firm num
Name
104640-2532 
9 461 622 594 
NP-VE4/10F2400LNP1157 
   
FUEL-INJECTION PUMP
Q




Information:

start by:a) remove pistons1. Check to be sure that all coolant has been removed from the cylinder block.2. Put a cover over the crankshaft journals before liners are removed. 3. Install tool (A) and remove the cylinder liners. 4. Remove filler band (1) and O-ring seals (2) from the cylinder liners.Install Cylinder Liners
1. Clean the cylinder liners and cylinder block. 2. Install the liners (1) in the cylinder block without the O-ring seals and filler bands. See CYLINDER LINER PROJECTION in TESTING AND ADJUSTING. 3. Install tooling (A) and two 5/8" - 11 NC bolts 5 1/2 in. long. Tighten the bolts evenly to 50 lb.ft. (70 N m).4. Check the liner projection with tool (B) at four locations around the liner.5. Liner projection must be .0020 to .0056 in. (0.051 to 0.142 mm). Measurements on the same liner must not be different by more than .002 in. (0.05 mm). Average measurement between liners next to each other must not be different by more than .002 in. (0.05 mm). The maximum permissible difference between average projection of all cylinder liners under one cylinder head is .004 in. (0.10 mm). The liner projection can change if the liner is turned in the bore. 6. If the liner projection is not .0020 to .0056 in. (0.051 to 0.142 mm), check the thickness of the liner flange (2) and the depth of the liner bore in the cylinder block. The thickness of the liner flange (2) must be .4048 .0008 in. (10.282 0.020 mm).7. The depth of the liner bore in the cylinder block must be .401 .001 in. (10.19 0.03 mm). If the liner bore in the block is worn and the measurement is not correct, the liner bore can be corrected with a cylinder block counterboring tool. See SPECIAL INSTRUCTIONS, FORM FM055228.8. Put a mark on the liner and cylinder block so the liner can be installed in the same position from which it was removed. 9. Install new O-ring seals (4) on the cylinder liners. Put liquid soap on the O-ring seals and in the bases in the cylinder block.
The liners must be installed in the cylinder block immediately after filler band (3) is installed. Make sure the marks on the liners and the cylinder block are in alignment when the cylinder liners are installed.
10. Put (dip) the filler band completely in clean SAE 30 oil and install it on the liner immediately.11. Install the liner in the cylinder block immediately with tooling (C).end by:a) install pistons

Have questions with 104640-2532?





Group cross 104640-2532 ZEXEL

9 461 617 577 
NP-VE4/10F2500LNP1142 
 
FUEL-INJECTION PUMP
9 461 619 956 
 
FUEL-INJECTION PUMP
9 461 622 591 
NP-VE4/10F2500LNP1143 
 
FUEL-INJECTION PUMP
9 461 622 592 
 
FUEL-INJECTION PUMP
9 461 623 553 
 
FUEL-INJECTION PUMP
9 461 619 957 
NP-VE4/10F2400LNP1156 
 
FUEL-INJECTION PUMP
9 461 622 593 
 
FUEL-INJECTION PUMP
104640-2532  
9 461 622 594 
NP-VE4/10F2400LNP1157 
 
FUEL-INJECTION PUMP
9 461 622 595 
 
FUEL-INJECTION PUMP
9 461 622 596 
 
FUEL-INJECTION PUMP
9 461 622 597 
 
FUEL-INJECTION PUMP
9 461 618 345 
NP-VE4/10F2500LNP1250 
 
FUEL-INJECTION PUMP
Back to top